BMW Vehicle Models X6 2019-2021 Torque Specifications
BMW Vehicle Models X6 2019-2021

BMW Vehicle Models X6 2019-2021 Torque Specifications

Complete BMW Vehicle Models X6 2019-2021 torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.

Updated

Important Information

Safety guidelines and reference information for proper torque application

Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083

Common Torque Patterns

Star Pattern

Used for wheels and other circular bolt patterns

Star Pattern torque pattern diagram showing proper bolt tightening sequence
Cross Pattern

Used for gaskets and cover plates

Cross Pattern torque pattern diagram showing proper bolt tightening sequence
Sequential Pattern

Used for head bolts and other critical components

Sequential Pattern torque pattern diagram showing proper bolt tightening sequence

Common Mistakes to Avoid

Over-tightening

Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.

Prevention:

Always use a calibrated torque wrench and follow specifications exactly.

Incorrect Torque Sequence

Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.

Prevention:

Follow the manufacturer's specified torque sequence pattern.

Dirty Threads

Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.

Prevention:

Clean and inspect all threads before assembly. Use new thread locker if specified.

Reusing TTY Bolts

Torque-to-yield bolts are designed to stretch and must not be reused.

Prevention:

Always replace TTY bolts with new ones. They are single-use only.

Dry vs. Lubricated

Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.

Prevention:

Check if specs are for dry or lubricated threads. Use specified lubricant when required.

Recommended Tools

Torque Wrench (1/4" Drive)

Range: 2-25 ft-lbs
Small fasteners, delicate components

Torque Wrench (3/8" Drive)

Range: 10-100 ft-lbs
Most common automotive fasteners

Torque Wrench (1/2" Drive)

Range: 30-250 ft-lbs
Large fasteners, wheels

Angle Gauge

Torque-to-yield (TTY) bolts

Torque Wrench Care

  • Calibrate annually or after 5,000 clicks
  • Store at lowest setting
  • Keep clean and lubricated

Search Specifications

Search by component name, bolt size, or description

Torque Calculator

Convert between different torque units

3.0l Engine

Torque specifications for 3.0L Engine

Cylinder Head

1

Cylinder Head Bolts

M12 x 1.75
Torque Specification
1. 15 ft-lbs (20 N·m) 2. 90° 3. 90°
Important Notes
These bolts are typically torque-to-yield and require an angle tightening sequence. Ensure bolts are replaced, and always use the correct sequence. Double-check the service manual for angle specification. These are estimated values based on common M12 cylinder head bolts.
2

Valve Cover Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Low torque value is to prevent distortion of the valve cover.
3

Rocker Arms/Shafts Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Tighten in sequence as per manual, and confirm with vehicle specific information. These are estimated values based on common M8 bolts in similar applications.
4

Camshaft Position Sensor Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten carefully, do not overtighten. These are estimated values based on common M6 bolts in similar applications.
5

Variable Valve Timing (VVT) Actuator Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Confirm the torque spec with the service manual. Some VVT system bolts may require a higher torque. These are estimated values based on common M6 bolts in similar applications.
6

Spark Plugs

M14 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Use a spark plug socket to properly tighten spark plugs. Do not overtighten.

Engine Block

1

Main Bearing Bolts

M12 x 1.5
Torque Specification
1. 20 ft-lbs (27 N·m) 2. 60° 3. 60°
Important Notes
These bolts are typically torque-to-yield and require an angle tightening sequence. Confirm with service manual. These are estimated values based on common M12 main bearing bolts.
2

Oil Pan Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Tighten in a criss-cross pattern to ensure even sealing. These are estimated values based on common M6 bolts in similar applications.
3

Oil Filter Housing Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Tighten in sequence as per manual. These are estimated values based on common M8 bolts in similar applications.
4

Oil Drain Plug

M14 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Use a new crush washer each time. Do not overtighten.
5

Crankshaft Position Sensor Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten carefully, do not overtighten. These are estimated values based on common M6 bolts in similar applications.
6

Knock Sensor Bolt

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Tighten carefully and do not overtighten. These are estimated values based on common M8 bolts in similar applications.
7

Engine Coolant Temperature Sensor

M12 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Tighten carefully, do not overtighten. These are estimated values based on common temperature sensors with M12 threads.
8

Oil Pressure Sensor

M12 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Tighten carefully, do not overtighten. These are estimated values based on common pressure sensors with M12 threads.
9

Water Pump Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten in a criss-cross pattern to ensure even sealing. These are estimated values based on common M6 bolts in similar applications.
10

Thermostat Housing Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Tighten in a criss-cross pattern to ensure even sealing. These are estimated values based on common M6 bolts in similar applications.

Connecting Rods

1

Connecting Rod Nuts

M9 x 1.25
Torque Specification
1. 15 ft-lbs (20 N·m) 2. 60° 3. 45°
Important Notes
These nuts are typically torque-to-yield and require an angle tightening sequence. Confirm with service manual. These are estimated values based on common M9 connecting rod bolts.

Flywheel

1

Flywheel Bolts

M10 x 1.5
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
Confirm the torque pattern with the service manual. These are estimated values based on common M10 flywheel bolts.

Timing System

1

Timing Belt/Chain Tensioner Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Tighten carefully and check for proper tensioner operation. These are estimated values based on common M8 bolts in similar applications.
2

Camshaft Sprocket Bolt

M10 x 1.5
Torque Specification
55 ft-lbs (75 N·m)
Important Notes
Check if this bolt is a stretch bolt and must be replaced. Confirm specific torque sequence with vehicle manual. These are estimated values based on common M10 camshaft sprocket bolts.

Accessory Drive

1

Crankshaft Pulley/Harmonic Balancer Bolt

M16 x 1.5
Torque Specification
90 ft-lbs (122 N·m)
Important Notes
Check if this bolt is a stretch bolt and must be replaced. Confirm specific torque with vehicle manual. These are estimated values based on common M16 crankshaft pulley bolts.
2

Water Pump Pulley Bolts

M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Tighten in sequence as per manual. These are estimated values based on common M6 bolts in similar applications.
3

Serpentine/Accessory Drive Belt Tensioner Bolt

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure proper belt tensioner function after tightening. These are estimated values based on common M8 bolts in similar applications.
4

Drive Belt Idler Pulley Bolt

M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure the pulley rotates freely after tightening. These are estimated values based on common M10 bolts in similar applications.
5

Power Steering Pump Mounting Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Tighten in a sequence as per manual. These are estimated values based on common M8 bolts in similar applications.
6

A/C Compressor Mounting Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Tighten in a sequence as per manual. These are estimated values based on common M8 bolts in similar applications.
7

Alternator Mounting Bolts

M10 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Tighten in a sequence as per manual. These are estimated values based on common M10 bolts in similar applications.

Intake System

1

Throttle Body Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten in a criss-cross pattern to ensure a proper seal. These are estimated values based on common M6 bolts in similar applications.
2

Intake Manifold Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Tighten in a specified sequence as per the service manual. These are estimated values based on common M8 bolts in similar applications.
3

Intake Air Temperature Sensor

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten carefully, do not overtighten. These are estimated values based on common sensors with M6 threads.
4

EGR Valve Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Tighten in a criss-cross pattern to ensure a proper seal. These are estimated values based on common M6 bolts in similar applications.

Fuel System

1

Fuel Rail Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten in sequence as per manual. These are estimated values based on common M6 bolts in similar applications.
2

Fuel Injector Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Tighten in sequence as per manual. These are estimated values based on common M6 bolts in similar applications.

Exhaust System

1

Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Tighten in the specified sequence as per the service manual. These are estimated values based on common M8 exhaust bolts.

Ignition System

1

Ignition Coil Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten carefully, do not overtighten. These are estimated values based on common M6 bolts in similar applications.

4.4l Engine

Torque specifications for 4.4L Engine

Cylinder Head

1

Cylinder Head Bolts

M12 x 1.75
Torque Specification
1. 15 ft-lbs (20 N·m) 2. 90° 3. 90°
Important Notes
Torque to spec, then angle tighten. Refer to the specific repair manual for the correct sequence and angle values. Cylinder head bolts are usually torque-to-yield and must be replaced.
2

Valve Cover Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten evenly in a criss-cross pattern to avoid distortion and leaks.

Engine Block

1

Main Bearing Bolts

M10 x 1.5
Torque Specification
1. 20 ft-lbs (27 N·m) 2. 60° 3. 60°
Important Notes
Torque to spec, then angle tighten. Refer to the specific repair manual for the correct sequence and angle values. Main bearing bolts are usually torque-to-yield and must be replaced.
2

Oil Pan Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Tighten bolts evenly in a criss-cross pattern to ensure a proper seal. Do not over tighten.
3

Oil Filter Housing Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Do not overtighten, or leaks may occur.
4

Oil Drain Plug Bolt

M14 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Always use a new crush washer when installing to ensure a proper seal. Do not overtighten.

Crankshaft And Rotating Assembly

1

Connecting Rod Nuts

M9 x 1.25
Torque Specification
1. 15 ft-lbs (20 N·m) 2. 70°
Important Notes
Torque to spec, then angle tighten. Refer to the specific repair manual for the correct sequence and angle values. Connecting rod nuts are usually torque-to-yield and must be replaced.
2

Flywheel Bolts

M10 x 1.5
Torque Specification
1. 50 ft-lbs (68 N·m) 2. 60°
Important Notes
Torque to spec, then angle tighten. Refer to the specific repair manual for the correct sequence and angle values. Flywheel bolts are usually torque-to-yield and must be replaced.
3

Crankshaft Pulley/Harmonic Balancer Bolt

M18 x 1.5
Torque Specification
1. 90 ft-lbs (122 N·m) 2. 90° 3. 90°
Important Notes
Torque to spec, then angle tighten. Refer to the specific repair manual for the correct sequence and angle values. Crankshaft pulley bolts are usually torque-to-yield and must be replaced.

Valvetrain

1

Camshaft Sprocket Bolts

M8 x 1.25
Torque Specification
55 ft-lbs (75 N·m)
Important Notes
Tighten evenly. Ensure correct timing when installing.
2

Rocker Arms/Shafts Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Tighten bolts evenly in the correct sequence.
3

Variable Valve Timing (VVT) Solenoid Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Do not overtighten. These bolts are usually small and can snap easily.

Timing System

1

Timing Belt/Chain Tensioner Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper tension is applied after tightening. Refer to your repair manual.

Intake System

1

Throttle Body Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure a proper seal; do not overtighten.
2

Intake Manifold Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Tighten evenly in a criss-cross pattern to ensure an airtight seal.
3

Intake Manifold Runner Control (IMRC) Valve Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure proper function after tightening.

Exhaust System

1

Exhaust Manifold/Headers to Cylinder Head Bolts/Studs

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Tighten evenly in a criss-cross pattern. Use new gaskets and check for leaks after installation. May require different torque if studs and nuts are used, refer to repair manual.
2

Turbocharger Mounting Bolts/Studs

M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Tighten in a criss-cross pattern, may require different torque if studs and nuts are used, refer to repair manual. Ensure proper alignment and no exhaust leaks.

Fuel System

1

Fuel Rail Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Do not overtighten, ensure a leak-free connection.
2

Fuel Injector Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Do not overtighten, ensure a proper seal.
3

Fuel Injector Rail Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Do not overtighten, ensure proper sealing.

Ignition System

1

Spark Plugs

M14 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Always use a torque wrench, improper torque can cause damage.
2

Ignition Coil Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Do not overtighten, ensure coils are properly seated.

Cooling System

1

Water Pump Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Do not overtighten; use a new gasket to prevent leaks.
2

Water Pump Pulley Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure proper alignment of pulley.
3

Thermostat Housing Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Ensure a proper seal, do not overtighten. Use a new gasket.
4

Coolant Temperature Sensor

M12 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure threads are clean and sensor is seated correctly. Do not over tighten.

Accessory Drive System

1

Serpentine/Accessory Drive Belt Tensioner Bolt

M10 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure proper belt tension after installation.
2

Drive Belt Idler Pulley Bolt

M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Do not over tighten, ensure pulley is aligned correctly.
3

Alternator Mounting Bolts

M10 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure proper alignment of the alternator and proper belt tension after install.
4

Power Steering Pump Mounting Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure pump is aligned correctly. Check for proper operation after install.

Sensors

1

Camshaft Position Sensor Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Do not overtighten, ensure sensor is properly seated.
2

Crankshaft Position Sensor Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Do not overtighten, ensure sensor is properly seated.
3

Knock Sensor Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure sensors are properly seated. Over or under tightening can lead to inaccurate readings.

Other Components

1

Starter Motor Mounting Bolts

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure proper alignment and engagement with flywheel/flexplate.
2

Turbocharger Oil Feed/Return Line Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use new crush washers to ensure a leak free connection.
3

PCV Valve Bolts/Fitting

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Ensure a good seal, do not over tighten.

8hp Transmission

Torque specifications for 8hp Transmission

Transmission Mounting

1

Transmission Mounting Bolts

M12 x 1.75
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Ensure bolts are of the correct grade for load bearing applications. Always use a calibrated torque wrench.

Oil Pan

1

Transmission Oil Pan Bolts

M8 x 1.25
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Tighten bolts in a criss-cross pattern to ensure even pressure on the gasket. Overtightening can distort the pan and cause leaks.

Drain And Fill Plugs

1

Transmission Drain Plug

M18 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Always replace the sealing washer (copper or o-ring) when re-installing the drain plug.
2

Transmission Fill Plug

M18 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Always replace the sealing washer (copper or o-ring) when re-installing the fill plug.

Mechatronic Unit

1

Mechatronic Unit Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Use a calibrated torque wrench. Tighten bolts in a criss-cross pattern to avoid damaging the mechatronic unit.

Valve Body

1

Valve Body Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten bolts in a criss-cross pattern. Avoid overtightening, which can damage the valve body.

Torque Converter

1

Torque Converter to Flexplate Bolts

M10 x 1.5
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Tighten bolts in a star pattern. Always use new bolts. Failure to properly torque these bolts can cause damage to the flexplate and driveline vibrations.

Cooler Line Fittings

1

Transmission Fluid Cooler Line Fittings

M18 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the o-rings are in good condition and properly seated. Over-tightening can damage fittings.

Bell Housing

1

Transmission Bell Housing Bolts

M12 x 1.75
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Tighten bolts in a star pattern to ensure even load distribution. Ensure proper alignment between the engine and transmission.

Body

Torque specifications for Body

Wheel Mounting

1

Wheel Lug Nuts

M14 x 1.25
Torque Specification
100 ft-lbs (136 N·m)
Important Notes
Tighten in a star pattern. Re-torque after initial drive. Always ensure threads are clean and lightly lubricated with anti-seize. Failure to do so may result in over or under torquing.

Fuel System

1

Fuel Tank Strap Bolts

M10 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure proper alignment of the fuel tank before tightening the bolts. Over-tightening can damage the tank or straps.
2

Fuel Filler Neck Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
These bolts secure the filler neck to the body panel. Over-tightening can damage the filler neck or surrounding body.

Hood Mounting

1

Hood Hinge Bolts (to Hood)

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
These bolts attach the hood to the hinges. Correct torque ensures proper hood alignment and function. Over tightening can cause damage to the hood or hinges.
2

Hood Hinge Bolts (to Body)

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
These bolts attach the hood hinges to the vehicle's body structure. Correct torque is crucial for hood alignment and smooth operation. Over tightening can cause damage to the body structure or hinges.

Door Mounting

1

Door Hinge Bolts (to Door)

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
These bolts secure the hinges to the door panel. Proper torque prevents misalignment and ensures smooth door operation.
2

Door Hinge Bolts (to Body)

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
These bolts secure the door hinges to the vehicle body. Correct torque prevents sagging or binding. Over tightening can cause damage to the body.

Fender Mounting

1

Fender Bolts (various locations)

M6 x 1.0
Torque Specification
8 ft-lbs (12 N·m)
Important Notes
Tighten gradually to ensure correct alignment. Torque values may slightly vary based on location. This is an estimated value, always check your service manual for exact locations.

Bumper Mounting

1

Bumper Cover Mounting Bolts/Screws (various locations)

M6 x 1.0
Torque Specification
8 ft-lbs (12 N·m)
Important Notes
These fasteners secure bumper covers to the vehicle body or bumper reinforcement. Over-tightening can damage the bumper cover or mounting tabs. This is an estimated value, always check your service manual for exact locations.

Tailgate Hatch Mounting

1

Tailgate/Hatch Hinge Bolts (to body)

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
These bolts connect the hinges to the vehicle body frame. Correct torque ensures the tailgate operates correctly. Over tightening may cause damage to hinges or the body
2

Tailgate/Hatch Strut Bolts (to body/tailgate)

M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
These bolts secure the tailgate struts to the body and tailgate. Proper torque is essential for correct operation. Over tightening may damage the strut mount or surrounding areas.

Lighting Mounting

1

Headlight Mounting Bolts/Screws

M5 x 0.8
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Proper torque prevents rattling and ensures secure mounting of the headlights. Over-tightening can damage the headlight housing. This is an estimated value, always check your service manual for exact locations.
2

Taillight Mounting Bolts/Screws

M5 x 0.8
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Correct torque avoids damage and ensures proper alignment of the taillight housing. Over-tightening can crack the housing. This is an estimated value, always check your service manual for exact locations.

Grille Mounting

1

Grille Mounting Bolts/Screws

M5 x 0.8
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
These fasteners secure the grille to the body panel. Over-tightening can damage the grille or surrounding body panels. This is an estimated value, always check your service manual for exact locations.

Running Board Mounting

1

Running Board/Side Step Mounting Bolts

M10 x 1.5
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
These bolts secure running boards or side steps to the vehicle's body. Over tightening can cause damage to the body or running board components. This is an estimated value, always check your service manual for exact locations.

Brakes

Torque specifications for Brakes

Caliper Mounting

1

Caliper Mounting Bolts

M14 x 1.5
Torque Specification
80 ft-lbs (108 N·m)
Important Notes
Secures the caliper directly to the mounting bracket. Ensure proper alignment before tightening.
2

Caliper Mounting Bracket Bolts

M16 x 1.5
Torque Specification
90 ft-lbs (122 N·m)
Important Notes
Secures the mounting bracket to the wheel hub or suspension knuckle. Apply thread locker for added security.

Caliper Components

1

Caliper Guide Pin Bolts/Bushing Bolts

M8 x 1.25
Torque Specification
27 ft-lbs (37 N·m)
Important Notes
These bolts secure the caliper guide pins, allowing the caliper to float. Torque value is an estimate; verify with the vehicle's service manual.
2

Brake Line Fitting to Caliper

M10 x 1.0 (Banjo Bolt)
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
These secure the brake line to the caliper. New crush washers must be used. Torque value is an estimate; verify with the vehicle's service manual.

Rotor Attachment

1

Rotor Retaining Bolts

M6 x 1.0
Torque Specification
12 ft-lbs (16 N·m)
Important Notes
Secures the rotor to the hub. These are typically small screws. Torque value is an estimate; verify with the vehicle's service manual.
2

Brake Rotor/Disc Set Screw

M5 x 0.8
Torque Specification
13 ft-lbs (18 N·m)
Important Notes
This small screw holds the rotor in place during assembly. Torque value is an estimate; verify with the vehicle's service manual.

Drivetrain

Torque specifications for Drivetrain

Flywheel Flexplate

1

Flywheel Bolts

M12 x 1.25
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
Apply thread locker to bolt threads. Ensure flywheel is correctly aligned.
2

Flex Plate Bolts

M12 x 1.25
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
Apply thread locker to bolt threads. Ensure flex plate is correctly aligned. Estimated value, confirm with specific vehicle service manual.

Transmission

1

Transmission Mounting Bolts

M12 x 1.75
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Ensure proper transmission alignment before tightening. Confirm proper torque with specific vehicle manual.
2

Transmission to Engine Bolts

M12 x 1.75
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Estimated value, check for vehicle specific torque. Some vehicles might combine these with mounting bolts.
3

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Tighten in a cross-pattern to ensure even pressure on the gasket. Confirm torque with specific vehicle manual.
4

Transmission Drain and Fill Plugs

M18 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Use a new sealing washer. Do not overtighten. Check vehicle specific torque.

Driveshaft

1

Propeller/Drive Shaft Bolts

M10 x 1.5
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Tighten bolts in a star pattern. Confirm with specific vehicle manual.
2

Rear Differential Output Flange Bolts

M10 x 1.5
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Tighten in a cross pattern. Estimated value, confirm with specific vehicle manual.

Axles

1

Drive Axle/Half Shaft Bolts

M10 x 1.5
Torque Specification
150 ft-lbs (203 N·m)
Important Notes
Apply thread locker to bolt threads. Confirm torque spec with specific vehicle manual.
2

CV Joint/Axle Nut

M24 x 1.5
Torque Specification
180 ft-lbs (244 N·m)
Important Notes
Use a new nut. Some vehicles might have a torque + angle spec, confirm with specific vehicle manual. Verify with specific manual for any additional pre-load steps.

Differential

1

Differential Housing Bolts

M12 x 1.75
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Tighten in a cross pattern. Use new bolts where necessary. Confirm specific torque value.
2

Differential Carrier Bolts

M10 x 1.5
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Tighten in a cross pattern. Estimated value, confirm with specific vehicle manual.
3

Differential Drain/Fill Plug

M18 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Use new sealing washer. Do not overtighten. Check specific torque with vehicle manual.

Transfer Case

1

Transfer Case Mounting Bolts

M12 x 1.75
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure proper alignment of the transfer case. Estimated value, check specific vehicle manual.
2

Transfer Case Drain/Fill Plug

M18 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Use a new sealing washer. Do not overtighten. Check specific torque with vehicle manual.

Electrical

Torque specifications for Electrical

Ignition System

1

Ignition Coil Mounting Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the mating surfaces are clean before installation. Proper torque is critical for a good electrical ground.
2

Camshaft Position Sensor Mounting Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Proper torque is essential for accurate sensor readings.
3

Crankshaft Position Sensor Mounting Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Proper torque is essential for accurate sensor readings.

Starter And Charging

1

Starter Motor Mounting Bolt

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the starter motor is properly aligned before tightening. Improper torque can cause damage to the motor casing or threads.
2

Alternator Mounting Bolt

M10 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure the alternator is properly aligned and the drive belt is correctly tensioned. Incorrect torque can lead to misalignment and vibration.

Battery And Grounding

1

Battery Terminal Nut

M6
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Do not over-tighten, as this could damage the battery posts. Use a torque wrench for accurate tightening.
2

Ground Strap/Cable Attachment Bolt to Chassis

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the mating surfaces are clean and free from corrosion. Proper grounding is crucial for electrical system performance.

Engine Control

1

Engine Control Unit (ECU/ECM) Mounting Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure the ECU is properly positioned before tightening. These bolts also provide a grounding point, so do not over-torque.
2

Oxygen (O2) Sensor Mounting Bolt

M8 x 1.25
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure the sensor is properly aligned and the threads are clean. Avoid over-tightening which can damage the threads or sensor housing.

Wiring And Distribution

1

Wiring Harness Connector Bracket Mounting Bolt

M5 x 0.8
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Securely fastens wiring harness to chassis to prevent vibration damage and poor electrical connections.
2

Fuse Box/Power Distribution Box Mounting Bolt

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Ensures a secure connection for power distribution. Over-tightening can damage plastic housing.

Lighting

1

Headlight Mounting Bolt

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Proper torque ensures secure mounting and proper sealing to prevent moisture intrusion.
2

Taillight Mounting Bolt

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Proper torque ensures secure mounting and proper sealing to prevent moisture intrusion.

Emissions Sensors

Torque specifications for Emissions_sensors

Exhaust Manifold

1

Exhaust Manifold to Cylinder Head Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Tighten bolts in a star pattern to ensure even pressure.
2

Exhaust Pipe to Exhaust Manifold Bolts

M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure proper alignment of the exhaust pipe to the manifold flange.

Catalytic Converter

1

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure proper alignment of the catalytic converter to the exhaust pipe. May require new gaskets.

Exhaust Sensors

1

Oxygen Sensor (O2 Sensor)

M18 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Apply anti-seize to sensor threads. Do not overtighten. Use a crows foot torque adapter to properly torque.
2

NOx Sensor Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure sensor is properly seated. Do not overtighten.
3

Particulate Matter Sensor Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure sensor is properly seated. Do not overtighten.
4

Exhaust Gas Temperature (EGT) Sensor Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure sensor is properly seated. Do not overtighten.

Egr System

1

EGR Valve Mounting Bolts

M8 x 1.25
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Ensure proper alignment of the EGR valve. May require new gaskets. Do not overtighten.

Exhaust System

1

Muffler to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure proper alignment of the muffler to the exhaust pipe. May require new gaskets.

Exhaust

Torque specifications for Exhaust

Exhaust Manifold

1

Exhaust Manifold to Cylinder Head Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Use a criss-cross pattern when tightening these bolts. Apply anti-seize compound to the threads.

Exhaust Pipe

1

Exhaust Pipe to Exhaust Manifold/Header Bolts

M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure the exhaust gasket is properly aligned before tightening. Use anti-seize compound on the threads.
2

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure the exhaust gasket is properly aligned before tightening. Use anti-seize compound on the threads.
3

Muffler to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure the exhaust gasket is properly aligned before tightening. Use anti-seize compound on the threads.
4

Exhaust Flange Bolts (Connecting Exhaust Sections)

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Use a criss-cross pattern when tightening these bolts. Apply anti-seize compound to the threads.

O2 Sensor

1

O2 Sensor Mounting

M18 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure the O2 sensor threads are clean. A new crush washer should be used for a proper seal.

Exhaust Hangers

1

Exhaust Hanger Bolts/Nuts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Do not overtighten these bolts, as it can deform the rubber mounts. Apply anti-seize compound to the threads.

Fuel

Torque specifications for Fuel

Fuel Rail

1

Fuel Rail Mounting Bolts

M8 x 1.25
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure proper seating of the fuel rail before tightening. Tighten bolts evenly in a criss-cross pattern.
2

Fuel Injector Mounting Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Tighten injector bolts evenly to prevent injector damage and ensure proper sealing. Be careful not to overtighten.

Fuel Pump

1

Fuel Pump Mounting Bolts

M8 x 1.25
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure the fuel pump gasket is correctly positioned. Tighten the mounting bolts evenly to prevent leaks and distortion.

Fuel System Lines

1

Fuel Line/Hose Banjo Bolt

M10 x 1.0
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Always use new crush washers when installing banjo bolts. Ensure proper alignment and do not over-tighten. This is an estimated torque value.
2

Fuel Filter Mounting Bolt/Nut

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure the fuel filter bracket is properly aligned. Tighten bolts or nuts evenly to secure the filter assembly to the chassis or component.

Fuel Tank

1

Fuel Filler Neck Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Ensure the filler neck is properly aligned to the body or fuel tank area to prevent leaks.
2

Fuel Tank Sending Unit/Lock Ring

Lock Ring (Estimated)
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure lock ring is evenly engaged and tightened to prevent leaks. This is an estimated value.

Hvac

Torque specifications for Hvac

Ac Compressor

1

A/C Compressor Mounting Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure the compressor is properly aligned before tightening bolts. Use a calibrated torque wrench.

Ac Lines

1

A/C Line Fittings

Varies
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Apply torque evenly to fittings. Ensure O-rings or gaskets are correctly seated before tightening. Do not over-tighten.

Ac Condenser

1

A/C Condenser Mounting Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
These bolts are typically M6. This value is an estimate based on typical M6 bolt torque. Ensure bolts are not cross-threaded.

Ac Evaporator

1

A/C Evaporator Housing Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
These bolts are typically M5 and often go into plastic. This is an estimated value. Do not over-tighten to avoid cracking the housing.

Ac Expansion Valve

1

A/C Expansion Valve Mounting Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
These bolts are typically M5. This value is an estimate. Ensure the expansion valve is aligned correctly before tightening bolts.

Hvac Actuators

1

HVAC Blend Door Actuator Mounting Bolts

Self-tapping screw
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
These are typically self-tapping screws into plastic. This is an estimated value. Be careful not to over-tighten and strip the plastic.

Blower Motor

1

Blower Motor Mounting Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
These bolts are typically M5. Ensure the motor is aligned properly before tightening bolts.

Temperature Sensors

1

Temperature Sensor Mounting Screws

Self-tapping screw
Torque Specification
N/A
Important Notes
These screws are installed by hand and are typically self-tapping into plastic. Do not over-tighten.

Suspension

Torque specifications for Suspension

Front Strut Assembly

1

Strut Upper Mounting Bolts

M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Tighten to specified torque. Ensure proper alignment of the strut assembly before tightening.
2

Strut Pinch Bolt/Spindle Clamp Bolt

M14 x 1.5
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Estimated value. Verify with your vehicle's service manual. This bolt clamps the steering knuckle to the strut body. Ensure the knuckle is fully seated before tightening.

Front Control Arms

1

Control Arm Mounting Bolts (Subframe)

M14 x 2.0
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
Tighten to specified torque. Ensure control arm is correctly seated.
2

Control Arm Ball Joint Nut

M12 x 1.5
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Tighten to specified torque. Make sure the ball joint is fully seated in the steering knuckle.

Steering

1

Tie Rod End Nut

M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Tighten to specified torque. Ensure the tie rod end is properly seated in the steering knuckle.

Sway Bar

1

Sway Bar Link Nut

M10 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Tighten to specified torque. Ensure the sway bar link is properly connected to the sway bar and the strut or control arm.
2

Sway Bar Mounting Bracket Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated value. Tighten to specified torque. Ensure the sway bar bracket is properly aligned to the frame.

Rear Suspension

1

Rear Strut Lower Mounting Bolt

M12 x 1.75
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Estimated value. Tighten to specified torque. Ensure the strut is properly seated in the lower mounting point.
2

Rear Upper Control Arm Bolts

M12 x 1.75
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Estimated value. Tighten to specified torque. Ensure control arm is correctly seated.
3

Subframe Mounting Bolts

M16 x 2.0
Torque Specification
1. 80 ft-lbs (108 N·m) 2. 90°
Important Notes
Estimated value. Follow specified torque sequence. These bolts often require torque plus angle method for proper tightening. Ensure correct alignment before torquing. Always use new bolts as they are often torque-to-yield.

Troubleshooting Guide

Common issues, diagnostic steps, and prevention guidelines

Common Issues

Bolt stretching, stripped threads, uneven torque patterns

Loose Components

Symptoms:
  • Rattling or vibration noises
  • Visible movement in components
  • Uneven panel gaps
Solutions:
  • Clean threads and mounting surfaces
  • Replace damaged fasteners
  • Apply proper torque in sequence
  • Use thread locker if specified

Stripped Fasteners

Symptoms:
  • Unable to achieve proper torque
  • Fastener spins freely
  • Visible thread damage
Solutions:
  • Use thread repair kit if appropriate
  • Install thread insert (HeliCoil)
  • Replace component if threaded hole is damaged
  • Upgrade to higher grade fastener if recommended

Overtightened Components

Symptoms:
  • Cracked or deformed parts
  • Broken fasteners
  • Compressed gaskets or seals
Solutions:
  • Replace damaged components
  • Use new fasteners
  • Follow proper torque sequence
  • Verify correct torque specifications

Diagnostic Steps

Visual inspection, torque verification, thread assessment

1

Visual Inspection

Inspect the affected area for any visible signs of damage or wear

  • Check for cracks or deformation
  • Look for signs of excessive wear
  • Verify proper fastener installation
2

Torque Verification

Verify the torque applied to the fasteners

  • Check the torque wrench calibration
  • Verify the torque specification
  • Compare the applied torque to the specification
3

Thread Assessment

Assess the condition of the threads

  • Check for signs of thread damage
  • Verify the thread type and size
  • Check for proper thread engagement

Prevention Guidelines

Best practices, maintenance tips, tool care

Best Practices

  • Always follow the recommended torque specification
  • Use the correct type and size of fasteners
  • Verify the torque wrench calibration regularly

Maintenance Tips

  • Regularly inspect the affected area for signs of wear or damage
  • Replace damaged or worn-out components promptly
  • Keep the work area clean and organized

Tool Care

  • Regularly clean and maintain the torque wrench
  • Store the torque wrench in a dry and secure location
  • Verify the torque wrench calibration before each use

Frequently Asked Questions

Find answers to common questions about torque specifications

Q1

What IS the recommended torque for lug nuts on my 2021 BMW X6?

140 Nm (103 ft-lbs)

Q2

What torque wrench do you recommend for tightening suspension bolts?

An adjustable torque wrench with a range of 20-100 Nm (15-75 ft-lbs)

Q3

How often should I check the torque on my brake caliper bolts?

Every 50,000 miles or as per manufacturer's maintenance schedule

Q4

Can I use a torque wrench to loosen bolts?

Yes, but it's not recommended as it may damage the torque wrench or bolt

Q5

What IS the torque spec for the engine oil drain plug?

25 Nm (18 ft-lbs)

Q6

How do I properly calibrate my torque wrench?

Refer to the torque wrench manufacturer's instructions and specifications

Environmental Considerations

Temperature, humidity, and seasonal effects on torque specifications

Temperature Effects

Includes: High Heat, Cold Weather, Thermal Cycling

Temperature can significantly impact torque values and fastener behavior

Cold Weather

Effects:
  • Increased material brittleness
  • Higher torque required due to thread contraction
  • Reduced thread lubricant effectiveness
Recommendations:
  • Allow components to warm to room temperature when possible
  • Consider using winter-grade thread lubricants
  • Check torque values more frequently during winter months

Hot Weather

Effects:
  • Thermal expansion of components
  • Decreased friction in threads
  • Accelerated lubricant breakdown
Recommendations:
  • Check torque when components are at normal operating temperature
  • Use temperature-resistant thread lockers
  • Consider re-torquing after heat cycles

Humidity and Corrosion

Covers: Rust Prevention, Salt Exposure, Moisture Control

Moisture and corrosion can affect fastener integrity and torque values

High Humidity

Effects:
  • Accelerated corrosion formation
  • Reduced friction coefficient
  • Potential thread seizing
Prevention:
  • Use corrosion-resistant fasteners
  • Apply appropriate anti-seize compounds
  • Maintain proper protective coatings

Salt Exposure

Effects:
  • Rapid corrosion development
  • Thread damage
  • Seized fasteners
Prevention:
  • Regular underbody washing
  • Use of sacrificial anodes where appropriate
  • Application of protective coatings

Seasonal Maintenance

Spring, Summer, Fall, and Winter maintenance schedules

Spring

  • Inspect for winter damage
  • Clean and protect exposed fasteners
  • Check torque on critical components

Summer

  • Monitor heat-affected components
  • Check expansion-related loosening
  • Inspect cooling system mounts

Fall

  • Prepare for winter conditions
  • Apply corrosion protection
  • Verify all fasteners are properly torqued

Winter

  • More frequent inspection of critical fasteners
  • Check for salt damage
  • Monitor suspension component torque

Related Resources

Tools, service procedures, and technical bulletins

Recommended Tools

BMW Measuring Value Display

Essential tool for BMW vehicles, providing real-time information on various vehicle systems, including torque specifications. Allows for accurate and convenient torque readings.

  • BMW-specific software and compatibility
  • Live data display for real-time monitoring
  • Detailed error code diagnostics
  • Compact design for easy storage and portability
Learn more

Digital Torque Wrench

Precision torque wrench with a digital display, ensuring accurate and repeatable torque application. Ideal for critical fasteners on the BMW x6, such as suspension and engine components.

  • High-precision torque measurement
  • Adjustable torque settings with digital display
  • Audible and visual indicators for target torque reached
  • Ergonomic design with comfortable grip
Learn more
Service Procedures

BMW x6 Bolt Torque Specifications Guide

Comprehensive guide covering all critical torque specifications for the BMW x6. Includes detailed instructions for each component and safety considerations.

  • Torque specifications for major components (e.g. engine, suspension, brakes)
  • Tightening sequences and precautions
  • Special instructions for performance upgrades or modifications
View full procedure
Technical Service Bulletins

x6 Suspension Component Updates

2021-05-15

Technical bulletin outlining updates to specific suspension components on the BMW x6. Provides revised torque specifications and installation instructions.

2020-2021 x6 M50i 2020-2021 x6 M50d

Resolution: Updated torque specifications for front and rear suspension components. Requires inspection and potential re-tightening of affected bolts.

x6 Engine Valve Cover Torque Correction

2019-12-10

Technical bulletin addressing incorrect torque specifications provided in the initial repair manual for the x6 valve cover. Provides updated and corrected torque values.

2019-2021 x6 xDrive30i 2019-2021 x6 xDrive40i

Resolution: Revised torque specifications for valve cover bolts. Requires retorquing of valve cover to prevent potential oil leaks.

Legal Disclaimer

Important information about using this content

Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.

General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability

The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.

We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.

Technical Information
  • All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
  • Vehicle specifications and procedures may vary by model year, trim level, and region.
  • Always follow the manufacturer's recommended procedures and safety precautions.
  • Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
  • If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.

About the Author

Expert automotive knowledge and experience

Alan Montanye - Automotive Technical Specialist
ASE

Alan Montanye

Automotive Technical Specialist

ASE Master Certified Technician with over a decade of hands-on experience in automotive repair and diagnostics.

Facebook Contact
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions

Diagnostic

Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.

Repair

Expert in both traditional mechanical repairs and modern vehicle systems.

Additional Expertise

Documentation

Created over 500 detailed repair guides and technical documents.

Training

Conducted technical training sessions and contributed to repair databases.

Certifications & Research

Certifications

  • ASE Master Technician Certification
  • Advanced Diagnostic Specialist
  • Hybrid/Electric Vehicle Systems
  • Performance Tuning Expert

Research & Community

Actively researches emerging technologies and contributes to automotive forums.

© 2025 BMW Specs. All rights reserved.

Privacy Policy Terms of Service