BMW Vehicle Models X5 2007-2013
BMW Vehicle Models X5 2007-2013 Torque Specifications
Complete BMW Vehicle Models X5 2007-2013 torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.
Updated
Important Information
Safety guidelines and reference information for proper torque application
Safety First
- Always verify torque specifications with your vehicle's factory service manual
- Use properly calibrated torque wrenches
- Replace all torque-to-yield (TTY) bolts - they are single-use only
- When in doubt, consult a professional mechanic
Quick Reference Guide
Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083
Common Torque Patterns
Star Pattern
Used for wheels and other circular bolt patterns
Cross Pattern
Used for gaskets and cover plates
Sequential Pattern
Used for head bolts and other critical components
Common Mistakes to Avoid
Common Mistakes to Avoid
Over-tightening
Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.
Prevention:
Always use a calibrated torque wrench and follow specifications exactly.
Incorrect Torque Sequence
Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.
Prevention:
Follow the manufacturer's specified torque sequence pattern.
Dirty Threads
Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.
Prevention:
Clean and inspect all threads before assembly. Use new thread locker if specified.
Reusing TTY Bolts
Torque-to-yield bolts are designed to stretch and must not be reused.
Prevention:
Always replace TTY bolts with new ones. They are single-use only.
Dry vs. Lubricated
Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.
Prevention:
Check if specs are for dry or lubricated threads. Use specified lubricant when required.
Recommended Tools
Recommended Tools
Torque Wrench (1/4" Drive)
Range: 2-25 ft-lbs
Small fasteners, delicate components
Torque Wrench (3/8" Drive)
Range: 10-100 ft-lbs
Most common automotive fasteners
Torque Wrench (1/2" Drive)
Range: 30-250 ft-lbs
Large fasteners, wheels
Angle Gauge
Torque-to-yield (TTY) bolts
Torque Wrench Care
- Calibrate annually or after 5,000 clicks
- Store at lowest setting
- Keep clean and lubricated
Search Specifications
Search by component name, bolt size, or description
Type to search through torque specifications. Use arrow keys to navigate results. Press Enter to select a result.
Torque Calculator
Convert between different torque units
3.0l Engine
Torque specifications for 3.0L Engine
3.0l Engine
Torque specifications for 3.0L Engine
Cylinder Head
1 Cylinder Head Bolts
M10 x 1.5
1
Cylinder Head Bolts
M10 x 1.5
Torque Specification
1. 18 ft-lbs (24 N·m)
2. 90°
3. 90°
Important Notes
Torque to 18 ft-lbs (24 N·m), then tighten an additional 90 degrees, then another 90 degrees. Always use new bolts. Follow specific tightening sequence outlined in service manual.
Crankshaft
1 Main Bearing Bolts
M12 x 1.75
1
Main Bearing Bolts
M12 x 1.75
Torque Specification
1. 55 ft-lbs (75 N·m)
2. 70°
Important Notes
Torque to 55 ft-lbs (75 N·m), then tighten an additional 70 degrees. Follow the specific tightening sequence in the service manual. Use new bolts if specified by manufacturer.
2 Flywheel Bolts
M10 x 1.25
2
Flywheel Bolts
M10 x 1.25
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Torque to 65 ft-lbs (88 N·m). Apply thread locker to the bolts. Tighten in a star pattern.
3 Crankshaft Pulley/Harmonic Balancer Bolt
M18 x 1.5
3
Crankshaft Pulley/Harmonic Balancer Bolt
M18 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Torque to 85 ft-lbs (115 N·m). Apply thread locker to the bolt. Use a crankshaft holding tool when tightening.
Connecting Rods
1 Connecting Rod Nuts
M9 x 1.0
1
Connecting Rod Nuts
M9 x 1.0
Torque Specification
1. 30 ft-lbs (41 N·m)
2. 60°
Important Notes
Torque to 30 ft-lbs (41 N·m), then tighten an additional 60 degrees. Use new nuts/bolts. Follow sequence specified in the service manual.
Valvetrain
1 Camshaft Sprocket Bolts
M8 x 1.25
1
Camshaft Sprocket Bolts
M8 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Torque to 35 ft-lbs (47 N·m). Ensure correct alignment of camshaft and sprocket.
2 Camshaft Bearing Cap Bolts
M6 x 1.0
2
Camshaft Bearing Cap Bolts
M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Torque to 10 ft-lbs (14 N·m). Tighten in the sequence specified in the service manual to prevent distortion.
3 Valve Cover Bolts
M6 x 1.0
3
Valve Cover Bolts
M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Torque to 10 ft-lbs (14 N·m). Tighten in the sequence specified in the service manual to ensure even gasket compression.
4 Rocker Arms/Shafts Bolts
M8 x 1.25
4
Rocker Arms/Shafts Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Torque to 18 ft-lbs (24 N·m). Tighten in the sequence specified in the service manual.
Timing System
1 Timing Belt/Chain Tensioner Bolt
M8 x 1.25
1
Timing Belt/Chain Tensioner Bolt
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Torque to 15 ft-lbs (20 N·m). Ensure proper timing chain/belt tension before tightening.
Intake System
1 Intake Manifold Bolts
M6 x 1.0
1
Intake Manifold Bolts
M6 x 1.0
Torque Specification
14 ft-lbs (19 N·m)
Important Notes
Torque to 14 ft-lbs (19 N·m). Tighten in sequence specified in the service manual to ensure even sealing.
2 Throttle Body Bolts
M6 x 1.0
2
Throttle Body Bolts
M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Torque to 10 ft-lbs (14 N·m). Ensure throttle body is correctly aligned before tightening.
3 EGR Valve Bolts
M8 x 1.25
3
EGR Valve Bolts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Torque to 15 ft-lbs (20 N·m). Ensure proper alignment of the EGR valve before tightening.
Exhaust System
1 Exhaust Manifold/Headers Bolts
M8 x 1.25
1
Exhaust Manifold/Headers Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Torque to 18 ft-lbs (24 N·m). Tighten bolts in the sequence specified in the service manual.
Fuel System
1 Fuel Rail Bolts
M6 x 1.0
1
Fuel Rail Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Torque to 9 ft-lbs (12 N·m). Ensure proper fuel rail alignment. Use a torque wrench to avoid overtightening.
2 Fuel Injector Bolts
M6 x 1.0
2
Fuel Injector Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Torque to 7 ft-lbs (10 N·m). Do not overtighten, this may damage the injector.
Ignition System
1 Spark Plugs
M14 x 1.25
1
Spark Plugs
M14 x 1.25
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Torque to 23 ft-lbs (31 N·m). Do not overtighten, or damage to the cylinder head can occur.
2 Ignition Coil Bolts
M6 x 1.0
2
Ignition Coil Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Torque to 8 ft-lbs (11 N·m). Do not overtighten.
Engine Cooling
1 Water Pump Bolts
M8 x 1.25
1
Water Pump Bolts
M8 x 1.25
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Torque to 11 ft-lbs (15 N·m). Tighten in sequence specified in the service manual to ensure proper sealing.
2 Water Pump Pulley Bolts
M8 x 1.25
2
Water Pump Pulley Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Torque to 18 ft-lbs (24 N·m). Ensure proper alignment of the pulley before tightening.
3 Thermostat Housing Bolts
M6 x 1.0
3
Thermostat Housing Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Torque to 7 ft-lbs (10 N·m). Ensure the thermostat is properly seated before tightening.
4 Coolant Temperature Sensor Bolt/Fitting
M12 x 1.5
4
Coolant Temperature Sensor Bolt/Fitting
M12 x 1.5
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Torque to 18 ft-lbs (24 N·m). If it is a fitting, a crows foot wrench will be required.
Lubrication System
1 Oil Pan Bolts
M6 x 1.0
1
Oil Pan Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Torque to 7 ft-lbs (10 N·m). Tighten in sequence specified in the service manual to ensure proper sealing.
2 Oil Filter Housing Bolt
M8 x 1.25
2
Oil Filter Housing Bolt
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Torque to 18 ft-lbs (24 N·m). Ensure proper alignment of the housing before tightening.
3 Oil Drain Plug Bolt
M14 x 1.5
3
Oil Drain Plug Bolt
M14 x 1.5
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Torque to 18 ft-lbs (24 N·m). Use a new sealing washer. Do not overtighten.
4 Oil Pressure Sensor Bolt/Fitting
M10 x 1.0
4
Oil Pressure Sensor Bolt/Fitting
M10 x 1.0
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Torque to 18 ft-lbs (24 N·m). If it is a fitting, a crows foot wrench may be required.
Engine Accessories
1 Serpentine/Accessory Drive Belt Tensioner Bolt
M8 x 1.25
1
Serpentine/Accessory Drive Belt Tensioner Bolt
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Torque to 18 ft-lbs (24 N·m). Ensure proper alignment of the tensioner before tightening.
2 Drive Belt Idler Pulley Bolt
M8 x 1.25
2
Drive Belt Idler Pulley Bolt
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Torque to 18 ft-lbs (24 N·m). Ensure proper alignment of the pulley before tightening.
Engine Sensors
1 Knock Sensor Bolts
M8 x 1.25
1
Knock Sensor Bolts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Torque to 15 ft-lbs (20 N·m). Ensure proper sensor seating.
2 VANOS Solenoid Bolts
M6 x 1.0
2
VANOS Solenoid Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Torque to 8 ft-lbs (11 N·m). Ensure proper solenoid seating.
Engine Covers
1 Timing Cover Bolts
M6 x 1.0
1
Timing Cover Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Torque to 7 ft-lbs (10 N·m). Tighten in the sequence specified in the service manual.
2 Timing Cover Bolts
M8 x 1.25
2
Timing Cover Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Torque to 18 ft-lbs (24 N·m). Tighten in the sequence specified in the service manual.
4.8l Engine
Torque specifications for 4.8L Engine
4.8l Engine
Torque specifications for 4.8L Engine
Cylinder Head
1 Cylinder Head Bolts
M12 x 1.5
1
Cylinder Head Bolts
M12 x 1.5
Torque Specification
1. 18 ft-lbs (24 N·m)
2. 90°
3. 90°
Important Notes
Cylinder head bolts are torque-to-yield; replace upon removal. Tighten in sequence according to the manufacturer's procedure. Torque values are estimated based on common specifications and may vary. Check the BMW TIS for the specific sequence and angle-tightening values.
2 Valve Cover Bolts
M6 x 1.0
2
Valve Cover Bolts
M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Tighten in a criss-cross pattern to ensure even pressure on the gasket.
3 Cylinder Head Cover Bolts
M6 x 1.0
3
Cylinder Head Cover Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten in a criss-cross pattern to ensure even pressure on the gasket.
4 Rocker Arm/Shaft Bolts
M8 x 1.25
4
Rocker Arm/Shaft Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure proper rocker arm alignment before tightening.
5 VANOS Solenoid Bolts
M6 x 1.0
5
VANOS Solenoid Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten carefully to avoid damage to the solenoid housing.
6 Camshaft Position Sensor Bolts
M6 x 1.0
6
Camshaft Position Sensor Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten carefully to avoid damaging the sensor.
Engine Block
1 Main Bearing Bolts
M12 x 1.5
1
Main Bearing Bolts
M12 x 1.5
Torque Specification
1. 20 ft-lbs (27 N·m)
2. 55 ft-lbs (75 N·m)
3. 50°
Important Notes
Main bearing bolts are torque-to-yield; replace upon removal. Tighten in sequence according to the manufacturer's procedure. Check BMW TIS for final angle.
2 Connecting Rod Nuts
M9 x 1.25
2
Connecting Rod Nuts
M9 x 1.25
Torque Specification
1. 15 ft-lbs (20 N·m)
2. 30 ft-lbs (41 N·m)
3. 60°
Important Notes
Connecting rod nuts are torque-to-yield; replace upon removal. Tighten in sequence according to the manufacturer's procedure. Check BMW TIS for final angle.
3 Oil Pan Bolts
M6 x 1.0
3
Oil Pan Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten in a criss-cross pattern to ensure even sealing of the oil pan gasket.
4 Crankshaft Position Sensor Bolts
M6 x 1.0
4
Crankshaft Position Sensor Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten carefully to avoid damaging the sensor.
5 Knock Sensor Bolts
M8 x 1.25
5
Knock Sensor Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure sensor is properly seated before tightening.
Timing System
1 Timing Belt/Chain Tensioner Bolt
M8 x 1.25
1
Timing Belt/Chain Tensioner Bolt
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure tensioner is properly positioned before tightening. Use a new tensioner if needed.
2 Camshaft Sprocket Bolt
M10 x 1.5
2
Camshaft Sprocket Bolt
M10 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure correct alignment of the camshaft sprockets. Use a camshaft holding tool as required.
Crankshaft And Flywheel
1 Flywheel Bolts
M12 x 1.5
1
Flywheel Bolts
M12 x 1.5
Torque Specification
1. 35 ft-lbs (47 N·m)
2. 65 ft-lbs (88 N·m)
3. 30°
Important Notes
Flywheel bolts are torque-to-yield; replace upon removal. Tighten in a star pattern, consult BMW TIS for the specific pattern.
2 Crankshaft Pulley/Harmonic Balancer Bolt
M16 x 1.5
2
Crankshaft Pulley/Harmonic Balancer Bolt
M16 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Ensure the pulley is fully seated against the crankshaft. Use a crankshaft holding tool to prevent rotation.
Intake System
1 Throttle Body Bolts
M6 x 1.0
1
Throttle Body Bolts
M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Tighten carefully to avoid damaging the throttle body.
2 Intake Manifold Bolts
M8 x 1.25
2
Intake Manifold Bolts
M8 x 1.25
Torque Specification
14 ft-lbs (19 N·m)
Important Notes
Tighten in a criss-cross pattern to ensure even pressure on the gasket.
3 Intake Air Temperature Sensor Bolt
M6 x 1.0
3
Intake Air Temperature Sensor Bolt
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten carefully to avoid damaging the sensor.
Exhaust System
1 Exhaust Manifold/Headers Bolts
M8 x 1.25
1
Exhaust Manifold/Headers Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Tighten in a sequence starting from the center out, to avoid manifold warpage.
2 Exhaust Manifold/Headers to Cylinder Head Bolts
M8 x 1.25
2
Exhaust Manifold/Headers to Cylinder Head Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Tighten in a sequence starting from the center out, to avoid manifold warpage.
3 EGR Valve Bolts
M8 x 1.25
3
EGR Valve Bolts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure EGR valve is properly positioned before tightening.
Fuel System
1 Fuel Rail Bolts
M6 x 1.0
1
Fuel Rail Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure fuel rail is properly seated before tightening. Use care when working with fuel system components.
2 Fuel Injector Bolts
M6 x 1.0
2
Fuel Injector Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten carefully to avoid damaging the injectors.
Cooling System
1 Water Pump Bolts
M8 x 1.25
1
Water Pump Bolts
M8 x 1.25
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Tighten in a criss-cross pattern to ensure even pressure on the gasket.
2 Water Pump Pulley Bolts
M6 x 1.0
2
Water Pump Pulley Bolts
M6 x 1.0
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure proper alignment of the pulley before tightening.
3 Thermostat Housing Bolts
M6 x 1.0
3
Thermostat Housing Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten carefully to avoid damaging the thermostat housing.
4 Coolant Temperature Sensor Bolt
M6 x 1.0
4
Coolant Temperature Sensor Bolt
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten carefully to avoid damaging the sensor.
Accessory Drive
1 Serpentine/Accessory Drive Belt Tensioner Bolt
M10 x 1.5
1
Serpentine/Accessory Drive Belt Tensioner Bolt
M10 x 1.5
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the tensioner is properly positioned before tightening.
2 Drive Belt Idler Pulley Bolt
M10 x 1.5
2
Drive Belt Idler Pulley Bolt
M10 x 1.5
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the idler pulley is properly positioned before tightening.
Lubrication System
1 Oil Filter Housing Bolt
M8 x 1.25
1
Oil Filter Housing Bolt
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the oil filter housing is properly seated before tightening. Use a new o-ring/seal if needed.
2 Oil Drain Plug Bolt
M12 x 1.5
2
Oil Drain Plug Bolt
M12 x 1.5
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Use a new sealing washer with each installation. Do not overtighten.
Ignition System
1 Spark Plugs
M14 x 1.25
1
Spark Plugs
M14 x 1.25
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Use a calibrated torque wrench to ensure proper heat transfer between the spark plug and the cylinder head. Check BMW TIS for specific installation procedures
2 Ignition Coil Bolts
M6 x 1.0
2
Ignition Coil Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten carefully to ensure proper coil contact and avoid damaging the coil housing.
Other
1 Fuel Filter Bolt/Nut
M8 x 1.25
1
Fuel Filter Bolt/Nut
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure fuel filter assembly is secure.
2 Power Steering Pump Mounting Bolts
M8 x 1.25
2
Power Steering Pump Mounting Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the power steering pump is properly aligned before tightening.
3 PCV Valve Bolt
M6 x 1.0
3
PCV Valve Bolt
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten carefully to avoid damaging the PCV valve.
6hp Transmission
Torque specifications for 6hp Transmission
6hp Transmission
Torque specifications for 6hp Transmission
Transmission Mounting
1 Transmission Mounting Bolts
M12 x 1.75
1
Transmission Mounting Bolts
M12 x 1.75
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper alignment before tightening. Check specific vehicle repair manual for confirmation.
Transmission Oil Pan
1 Transmission Oil Pan Bolts
M6 x 1.0
1
Transmission Oil Pan Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten bolts in a crisscross pattern to ensure even gasket compression. Over-tightening can cause leaks.
Transmission Drain Fill Plugs
1 Transmission Drain and Fill Plugs
M24 x 1.5
1
Transmission Drain and Fill Plugs
M24 x 1.5
Torque Specification
29 ft-lbs (40 N·m)
Important Notes
Use a new sealing washer or O-ring. Ensure threads are clean. Check specific vehicle repair manual for confirmation.
Valve Body
1 Valve Body Mounting Bolts
M6 x 1.0
1
Valve Body Mounting Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten bolts in a crisscross pattern to ensure even clamping pressure. Over-tightening can damage the valve body. Use new bolts if specified by manufacturer.
Mechatronic Unit
1 Mechatronic Unit Mounting Bolts
M6 x 1.0
1
Mechatronic Unit Mounting Bolts
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten bolts in a crisscross pattern. Over-tightening can damage the mechatronic unit housing. Use new bolts if specified by manufacturer.
Transmission Cooler Line Fittings
1 Transmission Cooler Line Fittings (General)
Varies
1
Transmission Cooler Line Fittings (General)
Varies
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Refer to specific fitting manufacturer's torque specifications. Use a backup wrench if necessary to avoid twisting the lines. This value is an estimate, please refer to the vehicle service manual.
Transmission Bellhousing
1 Transmission Bellhousing Bolts
M12 x 1.75
1
Transmission Bellhousing Bolts
M12 x 1.75
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Check specific repair manual for confirmation as this value may vary by engine. Ensure all bolts are tightened evenly.
Transmission Output Flange
1 Transmission Output Flange Bolts
M10 x 1.5
1
Transmission Output Flange Bolts
M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Tighten bolts evenly. Check specific repair manual for confirmation.
Transmission Adaptor Plate
1 Adaptor Plate to Transmission Case Bolts
M12 x 1.75
1
Adaptor Plate to Transmission Case Bolts
M12 x 1.75
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Check specific repair manual for confirmation as this value may vary. Ensure even tightening.
Body
Torque specifications for Body
Body
Torque specifications for Body
Fuel System
1 Fuel Tank Strap Bolts
M10 x 1.5
1
Fuel Tank Strap Bolts
M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure proper strap alignment before tightening. Check for any signs of damage or corrosion on the straps and mounting points.
2 Fuel Filler Neck Bolts
M6 x 1.0
2
Fuel Filler Neck Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Do not over-tighten these bolts to prevent damage to the fuel filler neck or the body. Ensure the filler neck gasket is properly seated.
Wheel Mounting
1 Wheel Lug Nuts
M14 x 1.5
1
Wheel Lug Nuts
M14 x 1.5
Torque Specification
88 ft-lbs (120 N·m)
Important Notes
Always use a star pattern when tightening lug nuts. Ensure lug nuts are properly seated against the wheel. Re-torque after 50-100 miles of driving.
Electrical System
1 Battery Terminal Nuts
M8 x 1.25
1
Battery Terminal Nuts
M8 x 1.25
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Do not over-tighten these nuts. Check for corrosion at the terminals and clean if necessary. Ensure a firm electrical connection.
Body Panels
1 Hood Hinge Bolts to Body
M8 x 1.25
1
Hood Hinge Bolts to Body
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value for M8 bolt. Ensure proper hood alignment before tightening the bolts.
2 Fender Bolts to Body
M8 x 1.25
2
Fender Bolts to Body
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value for M8 bolt. Ensure proper fender alignment before tightening the bolts.
3 Door Hinge Bolts to Body
M10 x 1.5
3
Door Hinge Bolts to Body
M10 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated value for M10 bolt. Ensure smooth door operation after tightening.
4 Door Latch/Striker Bolts to Body
M8 x 1.25
4
Door Latch/Striker Bolts to Body
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value for M8 bolt. Ensure the door latches securely after tightening.
5 Bumper Cover Mounting Bolts/Screws to Body
M6 x 1.0
5
Bumper Cover Mounting Bolts/Screws to Body
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated value for plastic body screw. Be careful not to over-tighten and damage the plastic components.
6 Tail Light Assembly Mounting Bolts/Screws to Body
M5 x 0.8
6
Tail Light Assembly Mounting Bolts/Screws to Body
M5 x 0.8
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Estimated value for plastic body screw. Be careful not to over-tighten and damage the plastic components. Ensure proper alignment and sealing.
Interior
1 Seat Mounting Bolts to Body
M10 x 1.5
1
Seat Mounting Bolts to Body
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Estimated value for M10 bolt. Ensure the seat is correctly positioned and stable after tightening.
2 Dash/Instrument Panel Mounting Bolts/Screws to Body
M5 x 0.8
2
Dash/Instrument Panel Mounting Bolts/Screws to Body
M5 x 0.8
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Estimated value, may vary depending on location, material, and size. Use care to not over-tighten.
Brakes
Torque specifications for Brakes
Brakes
Torque specifications for Brakes
Caliper Mounting
1 Caliper Mounting Bolts
M12 x 1.75
1
Caliper Mounting Bolts
M12 x 1.75
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Secures the caliper directly to the mounting bracket. Ensure bolts are clean and threads are in good condition. Apply even pressure during tightening.
2 Caliper Mounting Bracket Bolts
M14 x 1.5
2
Caliper Mounting Bracket Bolts
M14 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Attaches the caliper mounting bracket to the steering knuckle or hub. Tighten in a cross pattern to ensure even clamping.
Rotor Mounting
1 Rotor Retaining Bolts
M8 x 1.25
1
Rotor Retaining Bolts
M8 x 1.25
Torque Specification
12 ft-lbs (16 N·m)
Important Notes
These bolts hold the rotor against the hub and have a low torque requirement. Do not over-tighten. Their primary purpose is to facilitate wheel installation, not structural clamping.
Wheel Mounting
1 Wheel Lug Nuts
M14 x 1.5
1
Wheel Lug Nuts
M14 x 1.5
Torque Specification
88 ft-lbs (120 N·m)
Important Notes
Use a star pattern or criss-cross pattern when torquing lug nuts. Essential for safety and preventing brake rotor warping. Ensure all lug nuts are evenly torqued.
Caliper Components
1 Brake Pad Retaining Pins/Bolts
M6 x 1
1
Brake Pad Retaining Pins/Bolts
M6 x 1
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Secures brake pads in caliper. Check manufacturer specifications for exact torque. This is an estimated value, actual value may vary. Not all calipers use bolts, some use retaining clips which do not have a torque spec. Always use new retaining bolts.
2 Brake Caliper Bleeder Screws
M10 x 1
2
Brake Caliper Bleeder Screws
M10 x 1
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Bleeder screws are tightened to a low torque to avoid damage. Hand-tighten then use a torque wrench. Estimated value, actual value may vary. Over tightening will damage the bleeder and require replacement.
3 Brake Hose Banjo Bolts
M10 x 1
3
Brake Hose Banjo Bolts
M10 x 1
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Use new copper sealing washers. Ensure proper orientation of the brake hose before tightening. Estimated value, actual value may vary. Critical for preventing leaks.
4 Anti-Rattle Spring/Pad Retaining Clip Bolts
M8 x 1.25
4
Anti-Rattle Spring/Pad Retaining Clip Bolts
M8 x 1.25
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Not all calipers have these bolts. Used to retain the anti-rattle springs or pad retaining clips. Check manufacturer specifications for exact torque. This is an estimated value, actual value may vary.
Drivetrain
Torque specifications for Drivetrain
Drivetrain
Torque specifications for Drivetrain
Engine To Transmission
1 Flywheel Bolts
M12 x 1.5
1
Flywheel Bolts
M12 x 1.5
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Ensure the flywheel is properly aligned before torquing bolts. Apply thread locker if specified in the service manual.
2 Torque Converter Bolts to Flywheel
M10 x 1.25
2
Torque Converter Bolts to Flywheel
M10 x 1.25
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
These bolts connect the torque converter to the flywheel/flex plate. Ensure the torque converter is fully seated.
3 Transmission Bellhousing Bolts
M12 x 1.75
3
Transmission Bellhousing Bolts
M12 x 1.75
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the transmission is aligned properly with the engine block before tightening. Apply thread locker where required
Transmission
1 Transmission Mounting Bolts
M12 x 1.75
1
Transmission Mounting Bolts
M12 x 1.75
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
These bolts secure the transmission to the chassis. Ensure proper alignment before torquing.
2 Transmission Oil Pan Bolts
M6 x 1.0
2
Transmission Oil Pan Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten these bolts evenly in a crisscross pattern to avoid leaks. Use new gasket if needed.
3 Transmission Drain and Fill Plugs
M18 x 1.5
3
Transmission Drain and Fill Plugs
M18 x 1.5
Torque Specification
29 ft-lbs (40 N·m)
Important Notes
Use a new sealing washer. Do not overtighten to avoid stripping threads.
Driveshaft And Axles
1 Drive Axle/Half Shaft Bolts
M10 x 1.5
1
Drive Axle/Half Shaft Bolts
M10 x 1.5
Torque Specification
66 ft-lbs (90 N·m)
Important Notes
These bolts connect the drive axles to the transmission and/or wheel hubs.
2 CV Joint/Axle Nut
M24 x 1.5
2
CV Joint/Axle Nut
M24 x 1.5
Torque Specification
177 ft-lbs (240 N·m)
Important Notes
This nut secures the CV joint/driveshaft to the wheel hub. Use a new nut if specified in service manual.
3 Propeller/Drive Shaft Bolts
M10 x 1.5
3
Propeller/Drive Shaft Bolts
M10 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
These connect the driveshaft to the transmission and differential flanges. Apply thread locker where required.
4 Center Support Bearing Bolts (If Applicable)
M8 x 1.25
4
Center Support Bearing Bolts (If Applicable)
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
These bolts secure the center support bearing of a two-piece driveshaft.
Differential And Transfer Case
1 Differential Mounting Bolts
M12 x 1.75
1
Differential Mounting Bolts
M12 x 1.75
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
These bolts secure the differential housing to the chassis. Ensure proper alignment before torquing.
2 Differential Drain/Fill Plug
M18 x 1.5
2
Differential Drain/Fill Plug
M18 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Use a new sealing washer. Do not overtighten to avoid stripping threads.
3 Transfer Case Drain/Fill Plug
M18 x 1.5
3
Transfer Case Drain/Fill Plug
M18 x 1.5
Torque Specification
29 ft-lbs (40 N·m)
Important Notes
Use a new sealing washer. Do not overtighten to avoid stripping threads.
4 Input/Output Shaft Flange Nut
M20 x 1.5
4
Input/Output Shaft Flange Nut
M20 x 1.5
Torque Specification
140 ft-lbs (190 N·m)
Important Notes
These nuts secure the output and input flanges of the differential and transfer case. Check for preload requirements if any.
Electrical
Torque specifications for Electrical
Electrical
Torque specifications for Electrical
Ignition System
1 Ignition Coil Mounting Bolt
M6 x 1.0
1
Ignition Coil Mounting Bolt
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure coils are seated correctly before tightening. Over-tightening may damage the coil or mounting point.
Starting System
1 Starter Motor Mounting Bolts
M10 x 1.5
1
Starter Motor Mounting Bolts
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper starter motor alignment before tightening.
Charging System
1 Alternator Mounting Bolts
M8 x 1.25
1
Alternator Mounting Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Check belt alignment after tightening.
Electrical Connections
1 Battery Terminal Nuts
M6 x 1.0
1
Battery Terminal Nuts
M6 x 1.0
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Do not over-tighten as this can damage the terminal. Ensure cable lug is correctly positioned.
2 Ground Strap/Cable Bolt to Chassis/Engine Block
M8 x 1.25
2
Ground Strap/Cable Bolt to Chassis/Engine Block
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure contact surfaces are clean and free of corrosion.
Electronic Control Units
1 Engine Control Unit (ECU) Mounting Bolts
M6 x 1.0
1
Engine Control Unit (ECU) Mounting Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Use caution to prevent damage to the ECU mounting points. This is an estimated value.
Sensors
1 Crankshaft Position Sensor Mounting Bolt
M6 x 1.0
1
Crankshaft Position Sensor Mounting Bolt
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure sensor is correctly seated. This is an estimated value.
2 Camshaft Position Sensor Mounting Bolt
M6 x 1.0
2
Camshaft Position Sensor Mounting Bolt
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure sensor is correctly seated. This is an estimated value.
Power Distribution
1 Fuse Box Mounting Bolts
M6 x 1.0
1
Fuse Box Mounting Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Do not over-tighten as this can damage plastic mounts. This is an estimated value.
2 Wiring Harness Connector Securing Hardware
M4 x 0.7
2
Wiring Harness Connector Securing Hardware
M4 x 0.7
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
This applies to securing screws or bolts often found in various high pin connectors and junction boxes. Ensure connector is fully seated before tightening. This is an estimated value.
Emissions Sensors
Torque specifications for Emissions_sensors
Emissions Sensors
Torque specifications for Emissions_sensors
Egr System
1 EGR Valve Mounting Bolts
M8 x 1.25
1
EGR Valve Mounting Bolts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure proper alignment of the EGR valve before tightening bolts. Use a new gasket when installing the EGR valve.
Exhaust Manifold
1 Exhaust Manifold to Cylinder Head Bolts
M10 x 1.5
1
Exhaust Manifold to Cylinder Head Bolts
M10 x 1.5
Torque Specification
1. 10 ft-lbs (14 N·m)
2. 18 ft-lbs (24 N·m)
Important Notes
Tighten bolts in a specified sequence (usually center outwards) to prevent warping. Use new gasket
2 Exhaust Pipe to Exhaust Manifold/Headers Bolts
M8 x 1.25
2
Exhaust Pipe to Exhaust Manifold/Headers Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure a new gasket is used. Tighten evenly to avoid leaks.
Catalytic Converter
1 Catalytic Converter to Exhaust Pipe Bolts
M10 x 1.5
1
Catalytic Converter to Exhaust Pipe Bolts
M10 x 1.5
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Always use new gaskets and ensure proper alignment to prevent leaks. Tighten evenly.
Oxygen Sensors
1 Oxygen Sensor Mounting Bolts/Studs
M8 x 1.25
1
Oxygen Sensor Mounting Bolts/Studs
M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Torque spec is an estimate based on typical sensor bolt size, always double-check the specific service manual for the correct torque. Use anti-seize compound on the threads.
Nox Sensors
1 NOx Sensor Mounting Bolts/Studs
M8 x 1.25
1
NOx Sensor Mounting Bolts/Studs
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the sensor is correctly aligned before tightening. This value is an estimate, confirm with specific service manual.
Exhaust
Torque specifications for Exhaust
Exhaust
Torque specifications for Exhaust
Exhaust Manifold
1 Exhaust Manifold to Cylinder Head
M8 x 1.25
1
Exhaust Manifold to Cylinder Head
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Tighten bolts in a crisscross pattern to ensure even pressure and a leak-free seal. It is recommended to use new gaskets when installing the exhaust manifold to cylinder head.
Front Exhaust Piping
1 Exhaust Pipe to Exhaust Manifold/Headers
M10 x 1.5
1
Exhaust Pipe to Exhaust Manifold/Headers
M10 x 1.5
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Tighten bolts in a crisscross pattern. Use new gaskets for proper sealing.
2 Catalytic Converter to Exhaust Pipe
M10 x 1.5
2
Catalytic Converter to Exhaust Pipe
M10 x 1.5
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Tighten in a crisscross pattern. Always replace gaskets. Check for proper alignment to avoid binding.
Mid Exhaust Piping
1 Exhaust Pipe Clamp (Small)
M8 x 1.25
1
Exhaust Pipe Clamp (Small)
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Use a torque wrench to evenly tighten clamp bolts to the specified torque. Do not overtighten as this can cause damage to the exhaust pipe or clamp. It's best practice to use new clamps when reassembling the exhaust system.
2 Exhaust Pipe Clamp (Large)
M10 x 1.5
2
Exhaust Pipe Clamp (Large)
M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Use a torque wrench to evenly tighten clamp bolts to the specified torque. Do not overtighten as this can cause damage to the exhaust pipe or clamp. It's best practice to use new clamps when reassembling the exhaust system.
Rear Exhaust Piping
1 Muffler to Exhaust Pipe
M10 x 1.5
1
Muffler to Exhaust Pipe
M10 x 1.5
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Tighten in a crisscross pattern. Always use new gaskets when reassembling.
Exhaust Mounting
1 Exhaust Hanger Bolts/Studs
M8 x 1.25
1
Exhaust Hanger Bolts/Studs
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Do not overtighten as it can damage rubber mounts. Check for wear, rust, and damage to mounts prior to reassembly.
Oxygen Sensors
1 Oxygen Sensor
M18 x 1.5 (Typical)
1
Oxygen Sensor
M18 x 1.5 (Typical)
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Always use a new crush washer when installing oxygen sensors. The use of anti-seize is not recommended because it can affect sensor readings. Do not overtighten as damage to the threads may occur.
Fuel
Torque specifications for Fuel
Fuel
Torque specifications for Fuel
Fuel Rail
1 Fuel Rail Mounting Bolts
M6 x 1.0
1
Fuel Rail Mounting Bolts
M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure bolts are tightened evenly to maintain a proper seal against the intake manifold or cylinder head.
2 Fuel Injector Mounting Bolts
M5 x 0.8
2
Fuel Injector Mounting Bolts
M5 x 0.8
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten evenly to avoid damaging injector o-rings or the manifold.
Fuel Delivery
1 Fuel Pump Mounting Bolts
M6 x 1.0
1
Fuel Pump Mounting Bolts
M6 x 1.0
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Tighten evenly to secure the pump to the tank or access panel.
2 Fuel Filter Mounting Bolts/Nuts
M8 x 1.25
2
Fuel Filter Mounting Bolts/Nuts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Tighten securely to prevent movement and leaks. These may secure a bracket or housing.
3 Fuel Line Banjo Bolt/Fitting
M12 x 1.5
3
Fuel Line Banjo Bolt/Fitting
M12 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Use new crush washers and tighten carefully to prevent leaks.
Fuel Tank
1 Fuel Tank Strap Bolts
M10 x 1.5
1
Fuel Tank Strap Bolts
M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure tank straps are properly aligned before tightening to avoid movement.
2 Fuel Filler Neck Bolts
M6 x 1.0
2
Fuel Filler Neck Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten evenly to prevent leaks from the filler neck to the body.
3 Fuel Tank Access Panel Bolts
M6 x 1.0
3
Fuel Tank Access Panel Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten evenly to ensure a secure seal, preventing vapor leaks.
4 Fuel Sending Unit Mounting Bolts
M5 x 0.8
4
Fuel Sending Unit Mounting Bolts
M5 x 0.8
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Do not over-tighten as this can damage the sending unit.
5 Fuel Sending Unit Retaining Ring
N/A - Retaining Ring
5
Fuel Sending Unit Retaining Ring
N/A - Retaining Ring
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Use the correct tool and torque to secure the sending unit, estimated value.
Fuel Regulation
1 Fuel Pressure Regulator Mounting Bolts
M6 x 1.0
1
Fuel Pressure Regulator Mounting Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Do not over-tighten as it could damage the regulator housing.
Hvac
Torque specifications for Hvac
Hvac
Torque specifications for Hvac
Ac Compressor
1 Compressor Mounting Bolts
M8 x 1.25
1
Compressor Mounting Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Tighten bolts in a star pattern to ensure even pressure and alignment. Ensure proper alignment of the compressor before tightening bolts.
Ac Lines
1 A/C Line Fittings
Various, typically M6 x 1.0 to M10 x 1.5 depending on fitting
1
A/C Line Fittings
Various, typically M6 x 1.0 to M10 x 1.5 depending on fitting
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Use a properly sized wrench and back-up wrench to prevent twisting the lines and connections. Lubricate O-rings with a compatible A/C oil before installation to prevent leaks. Ensure fittings are properly aligned before tightening to prevent cross-threading.
Evaporator Housing
1 Evaporator Housing Bolts/Screws
M5 x 0.8
1
Evaporator Housing Bolts/Screws
M5 x 0.8
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
These are low torque fasteners, be careful not to overtighten them, as they are installed into plastic. Tighten evenly in a criss-cross pattern. This value is an estimate.
Condenser
1 Condenser Mounting Bolts/Fasteners
M6 x 1.0
1
Condenser Mounting Bolts/Fasteners
M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the condenser is correctly aligned before tightening. These fasteners are often installed into thin sheet metal or plastic; use caution to avoid stripping. This value is an estimate.
Blower Motor
1 Blower Motor Mounting Bolts/Screws
M4 x 0.7
1
Blower Motor Mounting Bolts/Screws
M4 x 0.7
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
These are low torque fasteners, often inserted into plastic. Avoid overtightening, which could strip the threads. This value is an estimate.
Hvac Control Module
1 HVAC Control Module/Unit Mounting Screws
M4 x 0.7
1
HVAC Control Module/Unit Mounting Screws
M4 x 0.7
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
These are very low torque fasteners, that are typically installed into plastic housings. Overtightening can easily strip the plastic housing. This value is an estimate.
Expansion Valve
1 Expansion Valve Bolts/Fittings
M6 x 1.0
1
Expansion Valve Bolts/Fittings
M6 x 1.0
Torque Specification
10 ft-lbs (13.5 N·m)
Important Notes
Tighten bolts evenly and in stages to ensure proper seal. Lubricate O-rings with compatible A/C oil. These bolts/fittings should be tightened evenly. This value is an estimate.
Ambient Air Temp Sensor
1 Ambient Air Temperature Sensor Mounting Screw
Self tapping screw, typically 4mm diameter
1
Ambient Air Temperature Sensor Mounting Screw
Self tapping screw, typically 4mm diameter
Torque Specification
0.5 ft-lbs (0.7 N·m)
Important Notes
This is a self tapping screw into plastic. Tighten by hand until the sensor is snug and secure, then add an additional 1/4 turn. Use extreme caution to not overtighten, which can crack the housing. This value is an estimate, based on a hand tight plus 1/4 turn.
Suspension
Torque specifications for Suspension
Suspension
Torque specifications for Suspension
Front Strut Assembly
1 Strut/Shock Absorber Mounting Bolts
M14 x 1.5
1
Strut/Shock Absorber Mounting Bolts
M14 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Secures the strut to the chassis or suspension knuckle. Ensure proper torque for suspension integrity.
2 Front Upper Strut Mount Nuts
M8 x 1.25
2
Front Upper Strut Mount Nuts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Secures the upper strut mount to the chassis. Important for proper strut mounting and vehicle support.
3 Front Lower Strut Pinch Bolt
M12 x 1.5
3
Front Lower Strut Pinch Bolt
M12 x 1.5
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Secures the strut housing to the steering knuckle. Critical for clamping the assembly together.
Front Control Arms
1 Control Arm Bolts
M16 x 1.5
1
Control Arm Bolts
M16 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Attaches control arms to chassis and knuckle. Crucial for alignment and suspension travel.
2 Ball Joint Nut
M12 x 1.25
2
Ball Joint Nut
M12 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Secures the ball joint stud. Ensures proper articulation and steering response.
Steering
1 Tie Rod End Nut
M12 x 1.5
1
Tie Rod End Nut
M12 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Secures the tie rod end to the steering knuckle. Maintains steering alignment and control.
Front Sway Bar
1 Sway Bar Link Nut
M10 x 1.25
1
Sway Bar Link Nut
M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Connects sway bar links to the sway bar and suspension. Important for reducing body roll.
2 Sway Bar Mounting Bracket Bolts
M8 x 1.25
2
Sway Bar Mounting Bracket Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Secures the sway bar to the chassis using mounting brackets.
Rear Shock Assembly
1 Rear Shock Absorber Upper Mount Bolts
M10 x 1.5
1
Rear Shock Absorber Upper Mount Bolts
M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Secures upper mount to chassis. Important for proper shock function.
Rear Control Arms
1 Rear Control Arm Inner Bolts
M14 x 1.5
1
Rear Control Arm Inner Bolts
M14 x 1.5
Torque Specification
1. 88 ft-lbs (120 N·m)
2. 90°
Important Notes
Attaches control arms to vehicle frame. Torque-to-yield bolts. Must replace after removal.
2 Rear Control Arm Outer Bolts
M14 x 1.5
2
Rear Control Arm Outer Bolts
M14 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Attaches control arms to wheel carrier/hub.
Rear Knuckle
1 Rear Suspension Knuckle/Wheel Carrier Mounting Bolts
M14 x 1.5
1
Rear Suspension Knuckle/Wheel Carrier Mounting Bolts
M14 x 1.5
Torque Specification
1. 81 ft-lbs (110 N·m)
2. 90°
Important Notes
Connects the rear hub assembly to the suspension. Torque-to-yield bolts. Must replace after removal.
Troubleshooting Guide
Common issues, diagnostic steps, and prevention guidelines
Common Issues
Bolt stretching, stripped threads, uneven torque patterns
Common Issues
Bolt stretching, stripped threads, uneven torque patterns
Loose Components
Symptoms:
- Rattling or vibration noises
- Visible movement in components
- Uneven panel gaps
Solutions:
- Clean threads and mounting surfaces
- Replace damaged fasteners
- Apply proper torque in sequence
- Use thread locker if specified
Stripped Fasteners
Symptoms:
- Unable to achieve proper torque
- Fastener spins freely
- Visible thread damage
Solutions:
- Use thread repair kit if appropriate
- Install thread insert (HeliCoil)
- Replace component if threaded hole is damaged
- Upgrade to higher grade fastener if recommended
Overtightened Components
Symptoms:
- Cracked or deformed parts
- Broken fasteners
- Compressed gaskets or seals
Solutions:
- Replace damaged components
- Use new fasteners
- Follow proper torque sequence
- Verify correct torque specifications
Diagnostic Steps
Visual inspection, torque verification, thread assessment
Diagnostic Steps
Visual inspection, torque verification, thread assessment
1
Visual Inspection
Inspect the affected area for any visible signs of damage or wear
- Check for cracks or deformation
- Look for signs of excessive wear
- Verify proper fastener installation
2
Torque Verification
Verify the torque applied to the fasteners
- Check the torque wrench calibration
- Verify the torque specification
- Compare the applied torque to the specification
3
Thread Assessment
Assess the condition of the threads
- Check for signs of thread damage
- Verify the thread type and size
- Check for proper thread engagement
Prevention Guidelines
Best practices, maintenance tips, tool care
Prevention Guidelines
Best practices, maintenance tips, tool care
Best Practices
- Always follow the recommended torque specification
- Use the correct type and size of fasteners
- Verify the torque wrench calibration regularly
Maintenance Tips
- Regularly inspect the affected area for signs of wear or damage
- Replace damaged or worn-out components promptly
- Keep the work area clean and organized
Tool Care
- Regularly clean and maintain the torque wrench
- Store the torque wrench in a dry and secure location
- Verify the torque wrench calibration before each use
Frequently Asked Questions
Find answers to common questions about torque specifications
Q1 What IS the recommended torque specification for the cylinder head bolts on a 2010 BMW X5 xDrive30i?
Q1
What IS the recommended torque specification for the cylinder head bolts on a 2010 BMW X5 xDrive30i?
According to BMW technical documentation, the cylinder head bolts should be tightened to a torque of 110 Nm (81 lb-ft) in three stages.
Q2 What type of torque wrench should I use for critical engine components?
Q2
What type of torque wrench should I use for critical engine components?
For precise torque application on critical engine components, a high-quality click-type or digital torque wrench IS recommended for accuracy and reliability.
Q3 IS it acceptable to use a thread-locking compound on all bolts?
Q3
IS it acceptable to use a thread-locking compound on all bolts?
No, thread-locking compound should only be applied to specific bolts as specified in the torque specifications table. Applying thread-locker to bolts where it's not required can affect the torque value and compromise joint integrity.
Q4 What are the torque specifications for the front wheel lug nuts?
Q4
What are the torque specifications for the front wheel lug nuts?
The torque specification for the front wheel lug nuts on a 2013 BMW X5 xDrive35i IS 140 Nm (103 lb-ft).
Q5 IS it important to follow the tightening sequence for bolts?
Q5
IS it important to follow the tightening sequence for bolts?
Yes, adhering to the specified tightening sequence ensures even distribution of load and prevents distortion of components. Tightening bolts in the wrong order can lead to uneven stress and potential failure.
Q6 What IS the torque range for the spark plugs on a 2007 BMW X5 3.0si?
Q6
What IS the torque range for the spark plugs on a 2007 BMW X5 3.0si?
The spark plugs on a 2007 BMW X5 3.0si should be tightened to 25 Nm (18 lb-ft).
Environmental Considerations
Temperature, humidity, and seasonal effects on torque specifications
Temperature Effects
Includes: High Heat, Cold Weather, Thermal Cycling
Temperature Effects
Includes: High Heat, Cold Weather, Thermal Cycling
Temperature can significantly impact torque values and fastener behavior
Cold Weather
Effects:
- Increased material brittleness
- Higher torque required due to thread contraction
- Reduced thread lubricant effectiveness
Recommendations:
- Allow components to warm to room temperature when possible
- Consider using winter-grade thread lubricants
- Check torque values more frequently during winter months
Hot Weather
Effects:
- Thermal expansion of components
- Decreased friction in threads
- Accelerated lubricant breakdown
Recommendations:
- Check torque when components are at normal operating temperature
- Use temperature-resistant thread lockers
- Consider re-torquing after heat cycles
Humidity and Corrosion
Covers: Rust Prevention, Salt Exposure, Moisture Control
Humidity and Corrosion
Covers: Rust Prevention, Salt Exposure, Moisture Control
Moisture and corrosion can affect fastener integrity and torque values
High Humidity
Effects:
- Accelerated corrosion formation
- Reduced friction coefficient
- Potential thread seizing
Prevention:
- Use corrosion-resistant fasteners
- Apply appropriate anti-seize compounds
- Maintain proper protective coatings
Salt Exposure
Effects:
- Rapid corrosion development
- Thread damage
- Seized fasteners
Prevention:
- Regular underbody washing
- Use of sacrificial anodes where appropriate
- Application of protective coatings
Seasonal Maintenance
Spring, Summer, Fall, and Winter maintenance schedules
Seasonal Maintenance
Spring, Summer, Fall, and Winter maintenance schedules
Spring
- Inspect for winter damage
- Clean and protect exposed fasteners
- Check torque on critical components
Summer
- Monitor heat-affected components
- Check expansion-related loosening
- Inspect cooling system mounts
Fall
- Prepare for winter conditions
- Apply corrosion protection
- Verify all fasteners are properly torqued
Winter
- More frequent inspection of critical fasteners
- Check for salt damage
- Monitor suspension component torque
Related Resources
Tools, service procedures, and technical bulletins
Recommended Tools
Digital Torque Wrench (10-100 Nm)
Essential for tightening fasteners to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the x5.
- Digital display for accurate readings
- Audible alarm when target torque IS reached
- Multiple units (Nm, ft-lb, in-lb)
- Reversible ratcheting mechanism
Service Procedures
Bolt Tightening Sequence for BMW x5 (2007-2013)
Proper bolt tightening sequence IS crucial to ensure even distribution of force and prevent component damage.
- Tighten bolts in a star pattern, working from the center outward.
- Follow the specified torque values for each bolt.
- Use a digital torque wrench for precise tightening.
- Double-check all bolts after tightening to ensure proper torque.
Replacing Brake Pads and Rotors on BMW x5 (2007-2013)
Step-by-step guide to safely replace brake pads and rotors, including torque specifications.
- Safety first: Park on a level surface, engage parking brake, and chock wheels.
- Remove the wheel and caliper.
- Replace pads and/or rotors.
- Torque caliper bolts to 110 Nm.
- Torque lug nuts to 140 Nm.
Technical Service Bulletins
BMW x5 Service Bulletin: Engine Oil Pan Bolt Over-Tightening
2010-05-15Over-tightening of the engine oil pan bolts can lead to oil leaks. This bulletin provides revised torque specifications.
2007-2010 x5 with N52 engine
Resolution: Oil pan bolts should be tightened to 25 Nm (18 ft-lb).
Legal Disclaimer
Important information about using this content
Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.
General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability
The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.
We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.
Technical Information
- All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
- Vehicle specifications and procedures may vary by model year, trim level, and region.
- Always follow the manufacturer's recommended procedures and safety precautions.
- Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
- If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.
About the Author
Expert automotive knowledge and experience
'/%3E%3Cpath d='M60 30a20 20 0 1 1 0 40 20 20 0 0 1 0-40zm0 45c16.5 0 30 7.5 30 16.8V100H30v-8.2c0-9.3 13.5-16.8 30-16.8z' fill='%23404040'/%3E%3C/svg%3E)
ASE
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions
Diagnostic
Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.
Repair
Expert in both traditional mechanical repairs and modern vehicle systems.
Additional Expertise
Documentation
Created over 500 detailed repair guides and technical documents.
Training
Conducted technical training sessions and contributed to repair databases.
Certifications & Research
Certifications
- ASE Master Technician Certification
- Advanced Diagnostic Specialist
- Hybrid/Electric Vehicle Systems
- Performance Tuning Expert
Research & Community
Actively researches emerging technologies and contributes to automotive forums.