BMW Vehicle Models M6 2005-2010 Torque Specifications
BMW Vehicle Models M6 2005-2010

BMW Vehicle Models M6 2005-2010 Torque Specifications

Complete BMW Vehicle Models M6 2005-2010 torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.

Updated

Important Information

Safety guidelines and reference information for proper torque application

Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083

Common Torque Patterns

Star Pattern

Used for wheels and other circular bolt patterns

Star Pattern torque pattern diagram showing proper bolt tightening sequence
Cross Pattern

Used for gaskets and cover plates

Cross Pattern torque pattern diagram showing proper bolt tightening sequence
Sequential Pattern

Used for head bolts and other critical components

Sequential Pattern torque pattern diagram showing proper bolt tightening sequence

Common Mistakes to Avoid

Over-tightening

Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.

Prevention:

Always use a calibrated torque wrench and follow specifications exactly.

Incorrect Torque Sequence

Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.

Prevention:

Follow the manufacturer's specified torque sequence pattern.

Dirty Threads

Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.

Prevention:

Clean and inspect all threads before assembly. Use new thread locker if specified.

Reusing TTY Bolts

Torque-to-yield bolts are designed to stretch and must not be reused.

Prevention:

Always replace TTY bolts with new ones. They are single-use only.

Dry vs. Lubricated

Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.

Prevention:

Check if specs are for dry or lubricated threads. Use specified lubricant when required.

Recommended Tools

Torque Wrench (1/4" Drive)

Range: 2-25 ft-lbs
Small fasteners, delicate components

Torque Wrench (3/8" Drive)

Range: 10-100 ft-lbs
Most common automotive fasteners

Torque Wrench (1/2" Drive)

Range: 30-250 ft-lbs
Large fasteners, wheels

Angle Gauge

Torque-to-yield (TTY) bolts

Torque Wrench Care

  • Calibrate annually or after 5,000 clicks
  • Store at lowest setting
  • Keep clean and lubricated

Search Specifications

Search by component name, bolt size, or description

Torque Calculator

Convert between different torque units

5.0l Engine

Torque specifications for 5.0L Engine

Cylinder Head

1

Cylinder Head Bolts

M12 x 1.75
Torque Specification
1. 15 ft-lbs (20 N·m) 2. 90° 3. 90°
Important Notes
Cylinder head bolts are torque-to-yield (TTY) and must be replaced each time they are removed. Follow the specific torque sequence specified in the official BMW service manual. Estimated values provided

Crankshaft

1

Main Bearing Bolts

M12 x 1.5
Torque Specification
1. 44 ft-lbs (60 N·m) 2. 70°
Important Notes
Main bearing bolts are torque-to-yield (TTY) and must be replaced each time they are removed. Follow the specific torque sequence specified in the official BMW service manual. Estimated values provided.
2

Connecting Rod Nuts

M9 x 1.0
Torque Specification
1. 18 ft-lbs (25 N·m) 2. 70°
Important Notes
Connecting rod nuts are often torque-to-yield (TTY) and should be replaced each time they are removed. Follow the specific torque sequence specified in the official BMW service manual. Estimated values provided.
3

Flywheel Bolts

M12 x 1.5
Torque Specification
88 ft-lbs (120 N·m)
Important Notes
Flywheel bolts are single-use and must be replaced each time they are removed. Tighten bolts in a star pattern.
4

Crankshaft Pulley/Harmonic Balancer Bolt

M18 x 1.5
Torque Specification
166 ft-lbs (225 N·m)
Important Notes
Crankshaft pulley/harmonic balancer bolts are single-use and must be replaced each time they are removed.

Oil System

1

Oil Pan Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten oil pan bolts in a crisscross pattern to ensure even sealing. Ensure a proper gasket or sealant is used.
2

Oil Filter Housing Bolt

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure the oil filter housing gasket is in good condition or replace it. Tighten evenly
3

Oil Drain Plug Bolt

M12 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Always use a new sealing ring on the oil drain plug.

Valve Train

1

Valve Cover Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten valve cover bolts in a crisscross pattern to ensure even sealing. Ensure a proper gasket is used.
2

Camshaft Sprocket Bolts

M10 x 1.25
Torque Specification
89 ft-lbs (120 N·m)
Important Notes
Camshaft sprocket bolts are usually single-use and must be replaced each time they are removed.
3

Rocker Arms/Shafts Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten rocker arm bolts evenly.
4

VANOS Solenoid Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the sealing surfaces are clean and use a new seal if necessary. Estimated value.
5

VANOS Unit Mounting Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Tighten the VANOS unit mounting bolts evenly. Estimated value.
6

VANOS Oil Line Bolts

M10 x 1.0
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure to use new sealing rings or crush washers. Estimated value

Timing System

1

Timing Belt/Chain Tensioner Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper tensioner alignment and operation after installation.

Intake System

1

Intake Manifold Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Tighten intake manifold bolts in a crisscross pattern to ensure even sealing.
2

Throttle Body Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the throttle body gasket is in good condition and in place.
3

Fuel Rail Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure proper seating of the fuel rail and injectors.
4

Fuel Injector Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the injector o-rings are in good condition and lubricated with fuel injector safe lubricant.
5

EGR Valve Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
This torque specification is only applicable if the engine is equipped with an EGR system. Ensure proper sealing of the EGR valve to prevent leaks.

Exhaust System

1

Exhaust Manifold/Headers to Cylinder Head Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Exhaust manifold bolts should always be replaced with new ones. Use a new exhaust manifold gasket, and tighten in a crisscross pattern.
2

Exhaust Flange Bolts

M8 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Tighten exhaust flange bolts evenly to prevent leaks. Ensure to use new gaskets if necessary.

Cooling System

1

Water Pump Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure proper sealing and use a new gasket if necessary. Tighten bolts evenly.
2

Water Pump Pulley Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten water pump pulley bolts evenly.
3

Thermostat Housing Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure proper sealing and use a new gasket if necessary. Tighten evenly

Electrical System

1

Ignition Coil Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten ignition coil bolts evenly.
2

Camshaft Position Sensor Bolt(s)

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten camshaft position sensor bolts evenly. Estimated value
3

Knock Sensor Bolt(s)

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Tighten knock sensor bolts evenly. Estimated value
4

Oil Pressure Sensor Bolt/Nut(s)

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten oil pressure sensor bolts evenly. Estimated value
5

Coolant Temperature Sensor Bolt/Nut(s)

M6 x 1.0
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Hand tight or low torque is critical to preventing damage to the components. Estimated Value.
6

Intake Air Temperature Sensor Bolt/Nut(s)

M6 x 1.0
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Hand tight or low torque is critical to preventing damage to the components. Estimated value

Engine Mounting

1

Engine Mount Bolts (to engine block)

M12 x 1.75
Torque Specification
1. 50 ft-lbs (68 N·m) 2. 90°
Important Notes
Engine mount bolts often involve a multi-step torque procedure. Follow the specific sequence specified in the official BMW service manual. Estimated values provided

Accessory Drive

1

Serpentine/Accessory Drive Belt Tensioner Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper tensioner alignment and operation after installation.
2

Drive Belt Idler Pulley Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper alignment and smooth operation of the idler pulley.

Engine Lifting

1

Engine Lifting Eye Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure lifting eyes are securely attached and free from damage.

Spark Plugs

1

Spark Plugs

M14 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure correct spark plug gap and do not over-torque as this could damage the threads in the cylinder head.

Body

Torque specifications for Body

Wheel Mounting

1

Wheel Lug Nuts

M14 x 1.5
Torque Specification
88 ft-lbs (120 N·m)
Important Notes
Tighten lug nuts in a star pattern.

Fuel System

1

Fuel Tank Strap Bolts

M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure straps are correctly positioned before tightening.
2

Fuel Filler Neck Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Do not overtighten to avoid damaging the filler neck.

Electrical System

1

Battery Terminal Nuts

M6 x 1.0
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Do not overtighten, ensure a clean and corrosion-free connection.

Suspension Mounting

1

Strut/Shock Absorber Mounting Bolts

M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure proper alignment of the strut before tightening.

Door Mounting

1

Door Hinge Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper door alignment before final tightening.
2

Door Latch/Lock Mechanism Mounting Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Check door latch operation after tightening.
3

Door Lock Actuator Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Do not overtighten the screws.
4

Rear Window Regulator Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Check window operation after tightening.

Hood Mounting

1

Hood Hinge Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper hood alignment before final tightening.

Exterior Body Panels

1

Fender Bolts

M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Tighten evenly to ensure proper alignment and prevent rattles.
2

Bumper Mounting Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure bumper is correctly aligned before tightening.

Trunk Hatch Mounting

1

Trunk Lid/Hatch Hinges/Support Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure smooth operation of the lid or hatch after tightening.

Interior Mounting

1

Seat Mounting Bolts

M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure correct seat position before tightening.
2

Seatbelt Mounting Bolts

M12 x 1.75
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure seatbelt mechanism functions correctly after tightening.
3

Dashboard/Instrument Panel Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the panel is properly aligned before tightening.

Roof Mounting

1

Sunroof/Moonroof Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Check the operation of sunroof/moonroof after tightening.

Trim Mounting

1

Exterior Trim Mounting Bolts/Clips

M4 x 0.7
Torque Specification
4 ft-lbs (5 N·m)
Important Notes
Do not over tighten, use low torque to prevent damage to fasteners or the trim.

Brakes

Torque specifications for Brakes

Caliper Mounting

1

Caliper Mounting Bolts

M12 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Secures the brake caliper to the mounting bracket. Ensure proper torque to maintain even clamping force.
2

Caliper Mounting Bracket Bolts

M14 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Secures the caliper mounting bracket to the wheel hub or steering knuckle. Proper torque is critical to maintain a secure brake assembly.

Rotor Mounting

1

Brake Rotor Retaining Bolts

M8 x 1.25
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
These bolts secure the brake rotor or drum to the wheel hub. This value is estimated and should be verified for this specific vehicle. Torque is critical for preventing rotor runout and vibrations.
2

Brake Rotor Set Screw

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Small set screw (often Torx or Phillips) to hold the rotor in place during assembly. Not designed to handle braking forces, just to aid in assembly. This is an estimated value based on similar M6 fasteners.

Brake Pad Hardware

1

Brake Pad Retaining Pin Bolt/Screw

M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Small bolt or screw to secure brake pad retaining pins or spring clips. This is an estimated value, and should be verified. Proper torque ensures pad contact and prevents brake noise.

Brake Lines

1

Brake Line Fitting Bolts at Caliper

M10 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Banjo bolts securing brake lines to the calipers. Requires specific torque to prevent leaks. This value is estimated.
2

Brake Line Fitting Bolts at Chassis/Hard Lines

M10 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Bolts attaching hard brake lines to the vehicle chassis or hose bracket. Maintaining a proper seal is critical. This value is estimated.

Bleeder Screws

1

Brake Bleeder Screw

M7 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Used to vent air from the brake system. Torque specification prevents damage to the screw. This is an estimated value and should be verified.

Parking Brake

1

Parking Brake Cable Adjustment Nut

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Used to adjust the parking brake cable tension. Proper torque prevents over-tightening. This value is estimated.

Abs Sensors

1

ABS Wheel Speed Sensor Mounting Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Mounting bolts for the ABS sensors. Proper torque ensures sensor alignment and function. This is an estimated value, and should be verified.

Drivetrain

Torque specifications for Drivetrain

Engine To Transmission

1

Flywheel Bolts

M12 x 1.5
Torque Specification
88 ft-lbs (120 N·m)
Important Notes
Use new bolts. Apply thread locker. Tighten in a star pattern.
2

Clutch Pressure Plate Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated value. Torque in a star pattern.

Transmission

1

Transmission Mounting Bolts

M12 x 1.75
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Tighten evenly, may need to be supported during tightening.
2

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Use new gasket or sealant. Tighten evenly to prevent leaks.
3

Transmission Drain and Fill Plugs

M22 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Use new crush washers.

Driveshaft And Axles

1

Propeller/Drive Shaft Bolts

M10 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Use thread locker. Check for proper alignment and ensure it is installed correctly.
2

Drive Axle/Half Shaft Bolts

M10 x 1.5
Torque Specification
75 ft-lbs (100 N·m)
Important Notes
Ensure the bolts are properly seated and tightened evenly.
3

CV Joint/Axle Nut

M24 x 1.5
Torque Specification
177 ft-lbs (240 N·m)
Important Notes
Use new nut if specified by the manufacturer. Torque with vehicle's wheel on the ground.

Differential

1

Differential Drain/Fill Plug

M20 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Use new crush washer.
2

Differential Output Flange Bolts

M10 x 1.25
Torque Specification
60 ft-lbs (80 N·m)
Important Notes
Estimated value. Tighten evenly.
3

Differential Mounting Bolts

M12 x 1.75
Torque Specification
47 ft-lbs (64 N·m)
Important Notes
Estimated value. Ensure differential is properly aligned before tightening. May need to be supported during tightening.

Subframe

1

Rear Subframe Mount Bolts

M14 x 1.5
Torque Specification
1. 80 ft-lbs (108 N·m) 2. 90°
Important Notes
Use new bolts. Tighten initial torque and then angle tightening for correct bolt stretch. Torque to Yield Bolt. Must be replaced when loosened.

Transfer Case

1

Transfer Case Mounting Bolts

M12 x 1.75
Torque Specification
47 ft-lbs (64 N·m)
Important Notes
Estimated value. Ensure the transfer case is aligned properly. May need to be supported during tightening.

Electrical

Torque specifications for Electrical

Ignition System

1

Ignition Coil Mounting Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensures proper grounding and positioning of the ignition coil. Do not overtighten as this can damage the coil. Use a calibrated torque wrench.

Starting System

1

Starter Motor Mounting Bolt

M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Critical for secure mounting and proper alignment with the flywheel. Ensure the starter motor is properly seated before tightening bolts.

Charging System

1

Alternator Mounting Bolt

M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensures proper belt alignment and grounding. Verify the alternator is properly positioned before tightening the bolts. Do not overtighten as this may damage the alternator.

Battery System

1

Battery Terminal Nut

M8 x 1.25
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Essential for a good electrical connection. Do not overtighten, as it can damage the battery terminals. Use a torque wrench to achieve the correct torque, as it is essential not to overtighten.

Engine Control Unit

1

ECU/DME Mounting Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure ECU is properly seated. Do not overtighten, as it can damage the ECU housing or mounting points. Estimated value based on typical M6 bolt torque in automotive applications.

Grounding System

1

Chassis/Engine Ground Strap Bolt

M8 x 1.25
Torque Specification
17 ft-lbs (23 N·m)
Important Notes
Critical for electrical grounding. Ensure both contact surfaces are clean. Torque value is an estimate based on typical M8 bolt torque in automotive applications.

Body Control Module

1

BCM Mounting Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensures secure mounting of the BCM. Do not overtighten, as it can damage the module. Estimated value based on typical M6 bolt torque in automotive applications.

Sensors

1

Crankshaft/Camshaft Position Sensor Mounting Bolt

M5 x 0.8
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensures correct sensor positioning and function. Values may vary by sensor. Estimated value based on typical M5 bolt torque in automotive applications.

Emissions Sensors

Torque specifications for Emissions_sensors

Exhaust System

1

Exhaust Manifold/Headers to Cylinder Head Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Tighten bolts in a cross-pattern to ensure even pressure. Apply a small amount of anti-seize compound to the threads.
2

Exhaust Pipe to Exhaust Manifold/Headers Bolts

M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Tighten bolts in a cross-pattern to ensure even pressure. Apply a small amount of anti-seize compound to the threads.
3

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Tighten bolts in a cross-pattern to ensure even pressure. Apply a small amount of anti-seize compound to the threads.

Oxygen Sensors

1

Oxygen Sensor (Pre-Catalytic Converter) Mounting

M18 x 1.5 or M22 x 1.5
Torque Specification
33 ft-lbs (44.7 N·m)
Important Notes
Ensure the sensor threads are clean and free of debris before installation. Torque value is an estimate, always verify with manufacturer specs if available.
2

Oxygen Sensor (Post-Catalytic Converter) Mounting

M18 x 1.5 or M22 x 1.5
Torque Specification
33 ft-lbs (44.7 N·m)
Important Notes
Ensure the sensor threads are clean and free of debris before installation. Torque value is an estimate, always verify with manufacturer specs if available.

Intake System

1

Mass Airflow Sensor (MAF) Mounting Bolts

M5 x 0.8
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Do not over-tighten. MAF sensors are often mounted to plastic housings which can be easily damaged. Ensure proper alignment before tightening.

Egr System

1

EGR Valve Mounting Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Tighten bolts in a cross-pattern to ensure even pressure.

Dpf System

1

Differential Pressure Sensor (DPF) Mounting Bolts

M5 x 0.8
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Do not over-tighten. Ensure proper alignment before tightening. This sensor is typically mounted to the DPF or a pipe connected to the DPF.

Nox System

1

NOx Sensor Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Do not over-tighten. Ensure proper alignment before tightening. This sensor is typically mounted to the exhaust system.

Exhaust

Torque specifications for Exhaust

Exhaust Manifold

1

Exhaust Manifold/Headers to Cylinder Head Bolts

M8 x 1.25
Torque Specification
1. 15 ft-lbs (20 N·m)
Important Notes
First stage tightening step. Always use a cross-tightening pattern.
2

Exhaust Manifold/Headers Bolts

M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
These bolts secure the manifold to other manifold parts or brackets. May be a final tightening step.
3

Exhaust Pipe to Exhaust Manifold/Headers Bolts

M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Connects the exhaust pipe to the manifold. Always use new gaskets.

Catalytic Converter

1

Catalytic Converter to Exhaust Pipe Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Connects catalytic converter to the exhaust pipe. Always use new gaskets.

Muffler

1

Muffler to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Secures the muffler to the exhaust pipe. Always use new gaskets if present.

Exhaust Flanges

1

Exhaust Flange Bolts/Nuts (Small)

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Typically used between mid-pipes or smaller sections. Estimated value, check your specific application. Always use a cross-tightening pattern.
2

Exhaust Flange Bolts/Nuts (Large)

M12 x 1.75
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Typically used in larger exhaust sections. Estimated value, check your specific application. Always use a cross-tightening pattern.

O2 Sensor

1

O2 Sensor

M18 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Thread sensor into exhaust. Do not over-torque. Estimated value, check your specific application.

Exhaust Hangers

1

Exhaust Hanger Bolts/Nuts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Secures hangers to the vehicle's undercarriage. Estimated value, check your specific application. Do not overtighten.

Exhaust Clamps

1

Exhaust Clamp (Small)

M8 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Typically for smaller slip joints. Estimated value, check your specific clamp size and type.
2

Exhaust Clamp (Large)

M10 x 1.5
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Typically for larger slip joints. Estimated value, check your specific clamp size and type.

Fuel

Torque specifications for Fuel

Fuel Rail

1

Fuel Rail Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure even tightening to prevent leaks. Clean mating surfaces before installation.
2

Fuel Injector Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure injector O-rings are properly seated to prevent leaks. Do not overtighten.
3

Fuel Pressure Regulator Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the regulator is seated correctly on its gasket or O-ring. Do not overtighten.
4

Fuel Rail Banjo Bolt (at Fuel Rail)

M12 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Always use new crush washers when installing banjo bolts. Ensure proper alignment before tightening.

Fuel Pump Assembly

1

Fuel Pump Mounting Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the fuel pump is properly seated in the tank before tightening. Do not overtighten.
2

Fuel Filter Mounting Bolt/Nut

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the filter is properly secured to prevent leaks. Clean mounting points.
3

Fuel Line Banjo Bolt (at Fuel Filter)

M12 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Always use new crush washers when installing banjo bolts. Ensure proper alignment before tightening.

Fuel Tank And Access

1

Fuel Tank Access Panel Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten evenly to maintain a proper seal. Ensure the panel is correctly positioned.
2

Fuel Level Sensor Mounting Screws

M5 x 0.8
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Do not overtighten the sensor screws as they can easily strip. Ensure proper contact with the tank.

Fuel Filler

1

Fuel Filler Neck Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure proper alignment of the filler neck to the body. Do not overtighten the bolts.

Getrag Transmission

Torque specifications for Getrag Transmission

Transmission Mounting

1

Transmission Mounting Bolts

M12 x 1.75
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure bolts are tightened evenly. Always double-check against the specific repair manual for your vehicle.

Transmission Oil Pan

1

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten bolts in a criss-cross pattern to ensure even pressure on the gasket. Over-tightening can deform the pan and cause leaks.

Drain Fill Plugs

1

Transmission Drain/Fill Plugs

M22 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Always use a new crush washer when installing drain and fill plugs to ensure a proper seal. Avoid over-tightening.

Drive Axle Bolts

1

Drive Axle/Half Shaft Bolts

M10 x 1.5
Torque Specification
75 ft-lbs (100 N·m)
Important Notes
Ensure bolts are tightened evenly. Under-torquing can cause bolts to loosen, and over-torquing can cause bolt failure.

Propeller Shaft Bolts

1

Propeller/Drive Shaft Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Tighten bolts evenly to prevent imbalance. Always check for proper driveshaft alignment after installation.

Input Shaft Bolts

1

Transmission Input Shaft Bolts

M10 x 1.5
Torque Specification
60 ft-lbs (80 N·m)
Important Notes
These bolts should be tightened in a star pattern to ensure even pressure. Improper torque can lead to misalignment and damage. Value is estimated, consult repair manual for confirmation.

Bellhousing Bolts

1

Transmission Bellhousing Bolts

M12 x 1.75
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Tighten bolts evenly. Ensure proper alignment before torquing. Value is estimated, consult repair manual for confirmation.

Clutch Slave Cylinder Bolts

1

Clutch Slave Cylinder Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the slave cylinder is properly positioned before torquing the bolts. Avoid over-tightening which could damage the cylinder. Value is estimated, consult repair manual for confirmation.

Shift Linkage Bolts

1

Shift Linkage Bolts

M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure all linkage components are properly aligned before torquing the bolts. Value is estimated, consult repair manual for confirmation.

Reverse Light Switch Bolts

1

Reverse Light Switch Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Do not over-tighten, as this can damage the sensor or cause leaks. Value is estimated, consult repair manual for confirmation.

Fluid Cooler Line Bolts

1

Transmission Fluid Cooler Line Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure all fittings are properly aligned before tightening. Over-tightening can damage fittings. Value is estimated, consult repair manual for confirmation.

Hvac

Torque specifications for Hvac

Ac Compressor

1

A/C Compressor Mounting Bolts

M8 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure bolts are clean and threads are in good condition. Use a criss-cross pattern when tightening to ensure even distribution of torque. Do NOT lubricate fasteners.
2

A/C Line Fittings

M10 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Inspect o-rings for damage before installation, replace if necessary. Ensure the fitting is properly aligned and seated. Do NOT lubricate fasteners.

Hvac Blower

1

HVAC Blower Motor Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the motor is properly aligned with the housing. These are typically low torque fasteners because the housing is usually made of plastic. Do NOT lubricate fasteners.

Hvac Controls

1

HVAC Control Module Mounting Screws/Bolts

M4 x 0.7
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Handle the control module with care to avoid damaging the electronics. These are usually small screws into plastic. Do NOT lubricate fasteners.
2

HVAC Blend Door Actuator Mounting Screws/Bolts

M4 x 0.7
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Make sure the actuator is aligned properly with the blend door linkage. These screws are typically low torque because the actuator is usually plastic. Do NOT lubricate fasteners.

Hvac Evaporator

1

HVAC Evaporator Core Housing Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the housing is properly aligned to ensure a good seal. Do NOT lubricate fasteners.

Ac Condenser

1

A/C Condenser Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the condenser is properly positioned and seated on its mount. Do NOT lubricate fasteners.

Ac Receiver Drier

1

A/C Receiver Drier Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the receiver drier is properly aligned before tightening. Do NOT lubricate fasteners.

Suspension

Torque specifications for Suspension

Front Strut Assembly

1

Strut to Body Mounting Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated value based on similar M8 chassis mounting bolts. Confirm in service manual.
2

Strut to Steering Knuckle Bolts

M14 x 1.5
Torque Specification
1. 65 ft-lbs (88 N·m) 2. 90°
Important Notes
Torque-to-yield bolts. Always use new bolts and follow the angle tightening procedure.
3

Upper Strut Mount Nut/Bolt

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Use a torque wrench. Do not overtighten. This is for the top center nut/bolt.

Front Control Arms

1

Control Arm to Chassis Bolts

M12 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Ensure the bolts are properly seated and tightened.
2

Ball Joint Nut

M12 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Ensure the ball joint stud is properly seated in the steering knuckle.

Steering System

1

Tie Rod End Nut

M12 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure proper seating of the tie rod end in the steering knuckle.
2

Steering Rack Mounting Bolts

M12 x 1.75
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Ensure the steering rack is properly aligned and seated on the chassis.

Sway Bar

1

Sway Bar Link Nut

M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure sway bar end links are correctly aligned.
2

Sway Bar Mounting Bracket Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure the sway bar is centered and the brackets are seated properly.

Rear Suspension

1

Rear Shock Absorber to Lower Control Arm Bolt

M14 x 1.5
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Ensure the shock absorber is properly aligned with the lower control arm.
2

Trailing Arm Bolts

M14 x 1.5
Torque Specification
75 ft-lbs (102 N·m)
Important Notes
Ensure the trailing arm is correctly aligned before tightening.

Troubleshooting Guide

Common issues, diagnostic steps, and prevention guidelines

Common Issues

Bolt stretching, stripped threads, uneven torque patterns

Loose Components

Symptoms:
  • Rattling or vibration noises
  • Visible movement in components
  • Uneven panel gaps
Solutions:
  • Clean threads and mounting surfaces
  • Replace damaged fasteners
  • Apply proper torque in sequence
  • Use thread locker if specified

Stripped Fasteners

Symptoms:
  • Unable to achieve proper torque
  • Fastener spins freely
  • Visible thread damage
Solutions:
  • Use thread repair kit if appropriate
  • Install thread insert (HeliCoil)
  • Replace component if threaded hole is damaged
  • Upgrade to higher grade fastener if recommended

Overtightened Components

Symptoms:
  • Cracked or deformed parts
  • Broken fasteners
  • Compressed gaskets or seals
Solutions:
  • Replace damaged components
  • Use new fasteners
  • Follow proper torque sequence
  • Verify correct torque specifications

Diagnostic Steps

Visual inspection, torque verification, thread assessment

1

Visual Inspection

Inspect the affected area for any visible signs of damage or wear

  • Check for cracks or deformation
  • Look for signs of excessive wear
  • Verify proper fastener installation
2

Torque Verification

Verify the torque applied to the fasteners

  • Check the torque wrench calibration
  • Verify the torque specification
  • Compare the applied torque to the specification
3

Thread Assessment

Assess the condition of the threads

  • Check for signs of thread damage
  • Verify the thread type and size
  • Check for proper thread engagement

Prevention Guidelines

Best practices, maintenance tips, tool care

Best Practices

  • Always follow the recommended torque specification
  • Use the correct type and size of fasteners
  • Verify the torque wrench calibration regularly

Maintenance Tips

  • Regularly inspect the affected area for signs of wear or damage
  • Replace damaged or worn-out components promptly
  • Keep the work area clean and organized

Tool Care

  • Regularly clean and maintain the torque wrench
  • Store the torque wrench in a dry and secure location
  • Verify the torque wrench calibration before each use

Frequently Asked Questions

Find answers to common questions about torque specifications

Q1

What torque should I use when tightening lug nuts on my 2005-2010 BMW M6?

Tighten lug nuts to a torque of 110 Nm (81 lb-ft).

Q2

What torque should I use when replacing the oil filter on my BMW M6?

Tighten the oil filter to a torque of 25 Nm (18 lb-ft).

Q3

What IS the torque specification for the spark plugs on a 2005-2010 M6?

Tighten spark plugs to a torque of 22 Nm (16 lb-ft).

Q4

What torque should be used when tightening the brake caliper mounting bolts?

Tighten the brake caliper mounting bolts to a torque of 120 Nm (89 lb-ft).

Q5

What IS the torque specification for the lower control arm mounting bolts on my BMW M6?

Tighten lower control arm mounting bolts to a torque of 100 Nm (74 lb-ft).

Q6

What tools do I need to measure torque accurately?

Use a calibrated torque wrench to ensure accurate torque measurements.

Environmental Considerations

Temperature, humidity, and seasonal effects on torque specifications

Temperature Effects

Includes: High Heat, Cold Weather, Thermal Cycling

Temperature can significantly impact torque values and fastener behavior

Cold Weather

Effects:
  • Increased material brittleness
  • Higher torque required due to thread contraction
  • Reduced thread lubricant effectiveness
Recommendations:
  • Allow components to warm to room temperature when possible
  • Consider using winter-grade thread lubricants
  • Check torque values more frequently during winter months

Hot Weather

Effects:
  • Thermal expansion of components
  • Decreased friction in threads
  • Accelerated lubricant breakdown
Recommendations:
  • Check torque when components are at normal operating temperature
  • Use temperature-resistant thread lockers
  • Consider re-torquing after heat cycles

Humidity and Corrosion

Covers: Rust Prevention, Salt Exposure, Moisture Control

Moisture and corrosion can affect fastener integrity and torque values

High Humidity

Effects:
  • Accelerated corrosion formation
  • Reduced friction coefficient
  • Potential thread seizing
Prevention:
  • Use corrosion-resistant fasteners
  • Apply appropriate anti-seize compounds
  • Maintain proper protective coatings

Salt Exposure

Effects:
  • Rapid corrosion development
  • Thread damage
  • Seized fasteners
Prevention:
  • Regular underbody washing
  • Use of sacrificial anodes where appropriate
  • Application of protective coatings

Seasonal Maintenance

Spring, Summer, Fall, and Winter maintenance schedules

Spring

  • Inspect for winter damage
  • Clean and protect exposed fasteners
  • Check torque on critical components

Summer

  • Monitor heat-affected components
  • Check expansion-related loosening
  • Inspect cooling system mounts

Fall

  • Prepare for winter conditions
  • Apply corrosion protection
  • Verify all fasteners are properly torqued

Winter

  • More frequent inspection of critical fasteners
  • Check for salt damage
  • Monitor suspension component torque

Related Resources

Tools, service procedures, and technical bulletins

Recommended Tools

Digital Torque Wrench (10-100 Nm)

Essential for applying the correct torque to bolts and nuts, ensuring proper assembly and preventing damage.

  • Digital display for precise readings
  • Audible alarm when target torque IS reached
  • Multiple units of measurement (Nm, ft-lb, in-lb)
  • Reversible ratcheting mechanism
Learn more
Service Procedures
Technical Service Bulletins

Legal Disclaimer

Important information about using this content

Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.

General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability

The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.

We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.

Technical Information
  • All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
  • Vehicle specifications and procedures may vary by model year, trim level, and region.
  • Always follow the manufacturer's recommended procedures and safety precautions.
  • Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
  • If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.

About the Author

Expert automotive knowledge and experience

Alan Montanye - Automotive Technical Specialist
ASE

Alan Montanye

Automotive Technical Specialist

ASE Master Certified Technician with over a decade of hands-on experience in automotive repair and diagnostics.

Facebook Contact
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions

Diagnostic

Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.

Repair

Expert in both traditional mechanical repairs and modern vehicle systems.

Additional Expertise

Documentation

Created over 500 detailed repair guides and technical documents.

Training

Conducted technical training sessions and contributed to repair databases.

Certifications & Research

Certifications

  • ASE Master Technician Certification
  • Advanced Diagnostic Specialist
  • Hybrid/Electric Vehicle Systems
  • Performance Tuning Expert

Research & Community

Actively researches emerging technologies and contributes to automotive forums.

© 2025 BMW Specs. All rights reserved.

Privacy Policy Terms of Service