BMW Vehicle Models M2 2022-present Torque Specifications
BMW Vehicle Models M2 2022-present

BMW Vehicle Models M2 2022-present Torque Specifications

Complete BMW Vehicle Models M2 2022-present torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.

Updated

Important Information

Safety guidelines and reference information for proper torque application

Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083

Common Torque Patterns

Star Pattern

Used for wheels and other circular bolt patterns

Star Pattern torque pattern diagram showing proper bolt tightening sequence
Cross Pattern

Used for gaskets and cover plates

Cross Pattern torque pattern diagram showing proper bolt tightening sequence
Sequential Pattern

Used for head bolts and other critical components

Sequential Pattern torque pattern diagram showing proper bolt tightening sequence

Common Mistakes to Avoid

Over-tightening

Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.

Prevention:

Always use a calibrated torque wrench and follow specifications exactly.

Incorrect Torque Sequence

Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.

Prevention:

Follow the manufacturer's specified torque sequence pattern.

Dirty Threads

Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.

Prevention:

Clean and inspect all threads before assembly. Use new thread locker if specified.

Reusing TTY Bolts

Torque-to-yield bolts are designed to stretch and must not be reused.

Prevention:

Always replace TTY bolts with new ones. They are single-use only.

Dry vs. Lubricated

Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.

Prevention:

Check if specs are for dry or lubricated threads. Use specified lubricant when required.

Recommended Tools

Torque Wrench (1/4" Drive)

Range: 2-25 ft-lbs
Small fasteners, delicate components

Torque Wrench (3/8" Drive)

Range: 10-100 ft-lbs
Most common automotive fasteners

Torque Wrench (1/2" Drive)

Range: 30-250 ft-lbs
Large fasteners, wheels

Angle Gauge

Torque-to-yield (TTY) bolts

Torque Wrench Care

  • Calibrate annually or after 5,000 clicks
  • Store at lowest setting
  • Keep clean and lubricated

Search Specifications

Search by component name, bolt size, or description

Torque Calculator

Convert between different torque units

3.0l Engine

Torque specifications for 3.0L Engine

Cylinder Head

1

Cylinder Head Bolts

M12 x 1.5
Torque Specification
1. 20 ft-lbs (27 N·m) 2. 90° 3. 90°
Important Notes
Follow specific tightening sequence. Angle torque required after initial torque. Cylinder head bolts are typically one-time use and must be replaced. Check the vehicle's repair manual for the exact angle torque value.
2

Rocker Arms/Shafts Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensures proper valve train operation.
3

Camshaft Position Sensor Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure proper sensor alignment.
4

Variable Valve Timing (VANOS) Solenoid Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Proper torque prevents leaks and ensures correct operation.
5

Exhaust Manifold/Headers to Cylinder Head Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Torque to spec to prevent exhaust leaks.
6

Spark Plugs

M14 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Use care not to cross-thread. Install with anti-seize.
7

Valve Cover Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Tighten evenly to prevent leaks. Do not overtighten.
8

Ignition Coil Bolt

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Do not overtighten.

Engine Block

1

Main Bearing Bolts

M12 x 1.5
Torque Specification
1. 60 ft-lbs (81 N·m) 2. 90°
Important Notes
Follow specific tightening sequence. Angle torque required after initial torque. Main bearing bolts are typically one-time use and must be replaced. Check the vehicle's repair manual for the exact angle torque value.
2

Connecting Rod Nuts

M9 x 1.25
Torque Specification
1. 30 ft-lbs (41 N·m) 2. 60°
Important Notes
Follow specific tightening sequence. Angle torque required after initial torque. Connecting rod nuts are typically one-time use and must be replaced. Check the vehicle's repair manual for the exact angle torque value.
3

Crankshaft Pulley/Harmonic Balancer Bolt

M14 x 1.5
Torque Specification
90 ft-lbs (122 N·m)
Important Notes
Use a crankshaft holding tool to prevent rotation. May require a new bolt.
4

Crankshaft Position Sensor Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure proper sensor alignment.
5

Knock Sensor Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Proper torque is critical for accurate readings.
6

Oil Pan Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Tighten evenly to prevent leaks. Do not overtighten.
7

Oil Drain Plug Bolt

M14 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Use a new sealing washer. Do not overtighten
8

Water Pump Bolts

M8 x 1.25
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Ensure proper sealing to prevent leaks.
9

Coolant Temperature Sensor Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure proper sensor alignment and sealing

Timing System

1

Timing Belt/Chain Tensioner Bolt

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Maintain proper timing chain tension.
2

Camshaft Sprocket Bolt

M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure proper alignment and timing. Use a cam holding tool.

Intake System

1

Throttle Body Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Torque to spec to prevent vacuum leaks. Do not overtighten.
2

Intake Manifold Bolts

M8 x 1.25
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Tighten evenly to prevent vacuum leaks. Do not overtighten.
3

EGR Valve Bolts

M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure proper sealing.
4

Fuel Rail Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Ensure proper fuel delivery. Do not overtighten.
5

Fuel Injector Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure proper fuel injector installation.
6

High Pressure Fuel Pump Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Proper torque is crucial for safe and efficient operation.

Cooling System

1

Water Pump Pulley Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Ensure proper belt alignment.
2

Thermostat Housing Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure proper sealing.

Accessory Drive

1

Serpentine/Accessory Drive Belt Tensioner Bolt

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Maintain proper drive belt tension.
2

Drive Belt Idler Pulley Bolt

M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure smooth drive belt operation.

8hp Transmission

Torque specifications for 8hp Transmission

Transmission Mounting

1

Transmission Mounting Bolts

M12 x 1.75
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Ensure bolts are in good condition, and threads are clean. Torque evenly.

Transmission Oil Pan

1

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Tighten in a criss-cross pattern to ensure even pressure and prevent leaks. Over-tightening may damage the threads in the aluminum housing.

Transmission Drain Fill Plugs

1

Transmission Drain and Fill Plugs

M18 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure the sealing surface is clean and undamaged. Use new crush washers or O-rings for sealing.

Mechatronics Unit

1

Mechatronics Unit Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Tighten in a criss-cross pattern. Over-tightening may cause damage to the Mechatronics Unit or transmission housing.

Valve Body

1

Valve Body Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Tighten in a criss-cross pattern. Over-tightening can cause damage to the valve body or transmission housing.

Bell Housing To Engine

1

Transmission Bell Housing to Engine Bolts

M12 x 1.75
Torque Specification
55 ft-lbs (75 N·m)
Important Notes
Ensure proper alignment of engine and transmission during installation. Use new bolts where specified.

Output Shaft Flange

1

Output Shaft Flange Bolt

M16 x 1.5
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
High-stress area; correct torque prevents play, vibration, and damage. Use new bolt when specified by manufacturer.

Body

Torque specifications for Body

Wheel System

1

Wheel Lug Nuts

M14 x 1.5
Torque Specification
90 ft-lbs (122 N·m)
Important Notes
Ensure lug nuts are tightened in a star pattern to ensure even clamping force.

Fuel System

1

Fuel Tank Strap Bolts

M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure straps are properly aligned before tightening to avoid bending or warping the tank.
2

Fuel Filler Neck Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Do not over-tighten to prevent damage to the filler neck flange.

Body Panels

1

Hood Hinge Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure proper hood alignment after tightening.
2

Fender Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Use a lower torque on inner fender bolts if applicable. Estimated value.
3

Door Hinge Bolts

M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure correct door alignment after tightening.
4

Door Latch Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the door closes and latches properly after tightening.
5

Bumper Mounting Bolts

M10 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Torque may vary depending on the bumper design. Estimated value.
6

Side Skirt/Rocker Panel Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Ensure side skirts/rocker panel are properly aligned before tightening. Estimated value.
7

Rear Spoiler/Wing Mounting Bolts

M6 x 1.0
Torque Specification
12 ft-lbs (16 N·m)
Important Notes
Do not overtighten the spoiler mounting bolts. Estimated value.

Lighting And Grille

1

Headlight Mounting Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Do not overtighten the headlight housing. Estimated value.
2

Taillight Mounting Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Do not overtighten the taillight housing. Estimated value.
3

Grille Mounting Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Do not overtighten the grille housing. Estimated value.

Interior Components

1

Seat Mounting Bolts

M8 x 1.25
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Torque values may vary by seat model. Use mid-range value. Ensure all bolts are fully tightened for safety.

Electrical Components

1

Body Control Module (BCM) Mounting Bolts

M4 x 0.7
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Do not overtighten the BCM mounting bolts. Estimated value.

Brakes

Torque specifications for Brakes

Caliper Mounting

1

Caliper Mounting Bracket Bolts

M12 x 1.5
Torque Specification
125 ft-lbs (169 N·m)
Important Notes
These high-strength bolts secure the caliper mounting bracket to the steering knuckle or hub carrier. Ensure proper torque to prevent loosening and maintain braking performance.
2

Brake Caliper Bolts

M12 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
These bolts secure the brake caliper to the mounting bracket. Proper torque is essential for safe and effective braking.

Rotor Attachment

1

Brake Disc/Drum Retaining Bolts

M6 x 1.0
Torque Specification
12 ft-lbs (16 N·m)
Important Notes
These smaller bolts hold the brake rotor/disc in place during wheel installation. Do not over-tighten, as they are not designed to withstand driving forces.

Hydraulic System

1

Brake Caliper Bleeder Screw

M10 x 1.0
Torque Specification
10 ft-lbs (13.5 N·m)
Important Notes
Estimated value. The bleeder screws must be properly tightened to ensure a leak-free seal and proper bleeding of the system. Do not overtighten.
2

Brake Line Fittings

M10 x 1.0
Torque Specification
13.5 ft-lbs (18.5 N·m)
Important Notes
Estimated value. Correct torque ensures a leak-free seal. Do not overtighten.
3

Brake Master Cylinder Mounting Bolts

M8 x 1.25
Torque Specification
22.5 ft-lbs (30.5 N·m)
Important Notes
Estimated value. These bolts secure the master cylinder to the brake booster or firewall. Proper torque is important to maintain alignment and prevent fluid leaks.

Booster And Pedal

1

Brake Booster Mounting Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated value. These bolts secure the brake booster to the firewall. Proper torque is essential for correct booster function.
2

Brake Pedal Pivot Bolt/Nut

M8 x 1.25
Torque Specification
17.5 ft-lbs (24 N·m)
Important Notes
Estimated value. Ensures the brake pedal operates smoothly and safely. Do not overtighten.

Pad Retention

1

Brake Pad Retaining Pin/Bolt

M6 x 1.0
Torque Specification
4 ft-lbs (5.5 N·m)
Important Notes
Estimated value. These small pins or bolts retain the brake pads within the caliper assembly. They do not require large torque, but need to be present and securely tightened to avoid rattling, premature brake wear, or damage. Do not overtighten.

Drivetrain

Torque specifications for Drivetrain

Engine Flywheel

1

Flywheel Bolts

M12 x 1.5
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Apply thread locker. Tighten in a star pattern. Ensure flywheel is properly seated against the crankshaft flange.
2

Clutch Pressure Plate Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Tighten in a star pattern. Ensure the clutch disc is centered.

Transmission

1

Transmission Mounting Bolts

M12 x 1.75
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Ensure transmission is properly aligned before tightening.
2

Transmission to Bell Housing Bolts

M10 x 1.5
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Ensure proper alignment before tightening.
3

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Tighten in a criss-cross pattern. Use a new gasket or sealant.
4

Transmission Drain and Fill Plugs

M18 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Use new sealing washers. Do not over-tighten.
5

Torque Converter Bolts

M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Tighten evenly. Ensure the torque converter is properly seated.

Driveshaft

1

Propeller/Drive Shaft Bolts

M10 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Apply thread locker. Tighten evenly in a circular pattern. Ensure correct alignment before tightening.

Axles

1

Drive Axle/Half Shaft Bolts

M10 x 1.5
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Ensure proper alignment of the axle before tightening. Tighten evenly.
2

CV Joint/Axle Nut

M24 x 1.5
Torque Specification
200 ft-lbs (271 N·m)
Important Notes
Use a new nut. Ensure proper seating of the CV joint.

Differential

1

Differential Mounting Bolts

M12 x 1.75
Torque Specification
80 ft-lbs (108 N·m)
Important Notes
Ensure proper alignment of the differential to the chassis. Torque may vary based on specific mounting design.
2

Differential Drain/Fill Plugs

M18 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Use new sealing washers. Do not over-tighten.

Transfer Case

1

Transfer Case Drain/Fill Plugs

M18 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Use new sealing washers. Do not over-tighten. Only applicable to AWD or 4WD vehicles.

Electrical

Torque specifications for Electrical

Ignition System

1

Ignition Coil Mounting Bolt

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Ensure proper seating of the coil before tightening. Avoid over-tightening to prevent damage to the coil or valve cover threads.

Starting System

1

Starter Motor Mounting Bolt

M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure the starter is correctly aligned with the flywheel housing before torquing the bolts. Tighten all mounting bolts evenly.

Charging System

1

Alternator Mounting Bolt

M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure proper belt alignment before final tightening. Tighten all mounting bolts evenly.

Battery System

1

Battery Terminal Nut

M8 x 1.25
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Ensure proper terminal contact and avoid over-tightening which can damage the terminals. Use a torque wrench for proper specification.

Engine Control Unit

1

ECU Mounting Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure proper seating and alignment of the ECU to the chassis before tightening. Do not over-torque.

Grounding System

1

Ground Strap/Cable Bolt (Chassis)

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Make sure the grounding surface is clean of debris or corrosion before tightening the bolts.
2

Ground Strap/Cable Bolt (Engine Block)

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Make sure the grounding surface is clean of debris or corrosion before tightening the bolts.

Sensor System

1

Crankshaft Position Sensor Mounting Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Tighten to the specified torque to avoid damage to sensor housing. Ensure the sensor is correctly aligned before tightening.
2

Camshaft Position Sensor Mounting Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Tighten to the specified torque to avoid damage to sensor housing. Ensure the sensor is correctly aligned before tightening.

Power Distribution

1

Fuse Box/Distribution Block Mounting Bolt/Screw

M5 x 0.8
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Avoid over-tightening which can damage the plastic housing. Ensure the box is correctly seated before tightening the mounting screws.

Lighting System

1

Headlight Housing Mounting Bolt/Screw

M5 x 0.8
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Ensure proper alignment before tightening to maintain a water tight seal. Avoid over-tightening, which can damage plastic housing or strip threads.

Emissions Sensors

Torque specifications for Emissions_sensors

Exhaust System

1

Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure even tightening to prevent leaks. Use new gaskets when reinstalling.
2

Exhaust Pipe to Exhaust Manifold/Headers Bolts

M10 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure even tightening to prevent leaks. Use new gaskets when reinstalling.
3

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure even tightening to prevent leaks. Use new gaskets when reinstalling.
4

Muffler to Exhaust Pipe Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure even tightening to prevent leaks. Use new gaskets when reinstalling.
5

Oxygen (O2) Sensor Mounting

M18 x 1.5 (Typical, varies by location)
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Use anti-seize on the sensor threads if applicable. This is an estimated torque value, verify with specific service documents for the exact sensor.
6

Nitrogen Oxide (NOx) Sensor Mounting

M16 x 1.5 (Typical, varies by location)
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Use anti-seize on the sensor threads if applicable. This is an estimated torque value, verify with specific service documents for the exact sensor.
7

Particulate Matter (PM) Sensor Mounting

M16 x 1.5 (Typical, varies by location)
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Use anti-seize on the sensor threads if applicable. This is an estimated torque value, verify with specific service documents for the exact sensor. Note: This sensor may not be present on all models.
8

Differential Pressure (DP) Sensor Mounting Bolts

M6 x 1.0
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure even tightening to prevent leaks. This is an estimated value, confirm with specific service documents.

Intake System

1

Mass Air Flow (MAF) Sensor Mounting Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Do not over-tighten. These are typically small bolts and easily damaged.
2

Intake Air Temperature (IAT) Sensor Mounting Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Do not over-tighten. These are typically small bolts and easily damaged. May be integrated with the MAF sensor.

Fuel System

1

Fuel Injector Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure proper alignment of the injector. Do not over-tighten, as it can damage the injector.
2

Fuel Injector Rail Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Tighten evenly to ensure a secure seal. Do not over-tighten, as it can damage the rail.

Egr System

1

EGR Valve Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure a proper seal between the EGR valve and its mating surface. Use new gaskets if available.

Exhaust

Torque specifications for Exhaust

Exhaust Manifold

1

Exhaust Manifold/Headers to Cylinder Head Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Tighten bolts in a star pattern. Proper torque is essential to prevent leaks and warping. It's important to check the service manual for the specific bolt sizes and thread pitch as they might vary on some engines.

Front Exhaust Section

1

Exhaust Pipe to Exhaust Manifold/Headers Bolts

M10 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure a new gasket is installed. Tighten bolts in a star pattern to prevent leaks. Double check bolt size.

Catalytic Converter

1

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure a new gasket is used. Tighten bolts in a star pattern.

Muffler Section

1

Muffler to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure new gaskets are used. Tighten bolts in a star pattern to ensure even pressure on the flange.

Exhaust Clamps

1

Exhaust Flange Clamp Bolts/Nuts

M8 x 1.25
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Torque value is an estimate based on common clamp sizes. Always refer to vehicle-specific manual or clamp manufacturer for precise specification. Over-tightening can damage clamp, under-tightening can lead to leaks. Check to ensure no gaps are present before final tightening.

Exhaust Hangers

1

Exhaust Hanger Bracket Bolts (to chassis)

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Torque value is an estimate. Ensure bracket is properly aligned and is supporting the exhaust before final tightening.

Oxygen Sensors

1

Oxygen Sensor into Exhaust Bung

M18 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Torque value is an estimate. Over-tightening can damage the threads and sensor. Sensor often contains thread sealant, verify proper function after install.

Fuel

Torque specifications for Fuel

Fuel Rail

1

Fuel Rail Mounting Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
These bolts secure the fuel rail to the intake manifold or cylinder head. Use new crush washers when reinstalling if applicable.
2

Fuel Injector Mounting Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
These bolts secure the fuel injectors to the fuel rail or intake manifold. Use new O-rings when reinstalling.

Fuel Pump

1

Fuel Pump Mounting Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
These bolts secure the fuel pump assembly to the fuel tank or chassis. Ensure proper alignment of the fuel pump before torquing.
2

High-Pressure Fuel Pump Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
These bolts secure the high-pressure fuel pump to the engine block or cylinder head. Proper torque is essential for secure and leak-free operation. It's critical to follow the manufacturers tightening sequence if specified.

Fuel Tank

1

Fuel Tank Strap Bolts

M12 x 1.75
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
These bolts secure the fuel tank straps. Ensure the straps are correctly positioned before tightening the bolts. Use caution to not damage fuel lines in the area.
2

Fuel Filler Neck Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
These bolts secure the fuel filler neck to the vehicle body or fuel tank. Ensure a proper seal is made when installing the filler neck and use new gaskets if applicable.

Fuel Lines

1

Low Pressure Fuel Line Banjo Bolts

M12 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Used for low-pressure fuel lines. Always use new crush washers. Ensure correct alignment of the banjo fitting before tightening.
2

High Pressure Fuel Line Banjo Bolts

M14 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Used for high-pressure fuel lines. Always use new crush washers and follow manufacturers procedure if it deviates from this.
3

Fuel Filter Bolt/Nut

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
This torque specification applies to any bolts or nuts securing the fuel filter assembly or its mounting bracket to the chassis or body. Correct torque ensures proper sealing and prevents fuel leaks.
4

Fuel Line Compression Fitting Nut

N/A
Torque Specification
1 ft-lbs (1 N·m)
Important Notes
Torque specification for compression fittings varies widely based on the fitting size and material. Consult the manufacturer's specific torque specifications for proper installation. The value provided is a placeholder. Estimated value.

Hvac

Torque specifications for Hvac

Ac Compressor

1

A/C Compressor Mounting Bolts

M10 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure proper alignment of the compressor before tightening. Use a criss-cross pattern when tightening multiple bolts.
2

A/C Line Fitting Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Use new O-rings or seals with each connection. Ensure the threads are clean. Do not over-tighten, as this can damage the fittings or seals.

Ac Condenser

1

A/C Condenser Mounting Bolts/Nuts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
These are typically smaller bolts. Ensure proper alignment before tightening. Value estimated based on common bolt size.

Ac Evaporator

1

A/C Evaporator Housing Bolts/Screws

M5 x 0.8
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
These screws secure the HVAC housing. Be careful not to over-tighten and crack plastic parts. Value estimated based on common screw size.
2

Expansion Valve Mounting Screws

M4 x 0.7
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Ensure proper alignment. These screws should be snug, not over-tightened. Value estimated based on common screw size.

Hvac Blower

1

HVAC Blower Motor Mounting Screws

M4 x 0.7
Torque Specification
4 ft-lbs (5 N·m)
Important Notes
Ensure proper alignment before tightening. These are typically small screws, do not over-tighten. Value estimated based on common screw size.

Ac Receiver Drier

1

A/C Receiver Drier/Desiccant Filter Mounting Bolt/Clamp

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Ensure the filter is properly positioned and the bolt/clamp is correctly aligned. Value estimated based on common bolt size.

Heater Core

1

Heater Core Connection Pipe Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Ensure proper alignment and use new gaskets or seals if required. Do not over-tighten to avoid damage to the core. Value estimated based on common bolt size.

Suspension

Torque specifications for Suspension

Front Strut Assembly

1

Strut/Shock Absorber Mounting Bolts (lower)

M14 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Secures the strut to the steering knuckle. Ensure bolts are clean and threads are in good condition. Tighten evenly.
2

Front Strut Tower to Body Bolts

M10 x 1.5
Torque Specification
48 ft-lbs (65 N·m)
Important Notes
Secures the top of the strut assembly to the chassis. Tighten in a cross pattern.
3

Steering Knuckle to Strut Clamp Bolts

M12 x 1.5
Torque Specification
1. 59 ft-lbs (80 N·m) 2. 90°
Important Notes
Secures the steering knuckle to the strut. Torque to the specified value and then angle. Use new bolts if specified by manufacturer.

Front Control Arms

1

Control Arm Bolts (chassis side)

M14 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Secures the control arm to the vehicle's subframe or chassis. Tighten with the vehicle at ride height if possible.
2

Front Lower Control Arm Ball Joint to Knuckle Bolt/Nut

M12 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Secures the ball joint to the steering knuckle. Ensure proper seating of the ball joint before tightening.

Rear Suspension

1

Rear Shock Tower to Body Bolts

M10 x 1.5
Torque Specification
48 ft-lbs (65 N·m)
Important Notes
Secures the top of the rear shock to the chassis. Tighten in a cross pattern.
2

Rear Lower Control Arm Ball Joint to Knuckle Bolt/Nut

M12 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Secures the rear ball joint to the knuckle. Ensure proper seating before tightening.

Steering Components

1

Tie Rod End Nut

M14 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Secures the tie rod end to the steering knuckle. Ensure proper alignment before tightening.

Sway Bar

1

Sway Bar Link Nut

M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Secures the sway bar links to the sway bar and strut/control arm. Tighten evenly on both sides.
2

Front Sway Bar Mounting Bracket Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Secures the sway bar mounting brackets to the chassis. Tighten evenly and in a cross pattern.
3

Rear Sway Bar Mounting Bracket Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Secures the rear sway bar mounting brackets to the chassis. Tighten evenly and in a cross pattern.

Sensors

1

Wheel Speed Sensor Bolt/Screw

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Secures the wheel speed sensor to the steering knuckle or suspension component. Do not overtighten.

Troubleshooting Guide

Common issues, diagnostic steps, and prevention guidelines

Common Issues

Bolt stretching, stripped threads, uneven torque patterns

Loose Components

Symptoms:
  • Rattling or vibration noises
  • Visible movement in components
  • Uneven panel gaps
Solutions:
  • Clean threads and mounting surfaces
  • Replace damaged fasteners
  • Apply proper torque in sequence
  • Use thread locker if specified

Stripped Fasteners

Symptoms:
  • Unable to achieve proper torque
  • Fastener spins freely
  • Visible thread damage
Solutions:
  • Use thread repair kit if appropriate
  • Install thread insert (HeliCoil)
  • Replace component if threaded hole is damaged
  • Upgrade to higher grade fastener if recommended

Overtightened Components

Symptoms:
  • Cracked or deformed parts
  • Broken fasteners
  • Compressed gaskets or seals
Solutions:
  • Replace damaged components
  • Use new fasteners
  • Follow proper torque sequence
  • Verify correct torque specifications

Diagnostic Steps

Visual inspection, torque verification, thread assessment

1

Visual Inspection

Inspect the affected area for any visible signs of damage or wear

  • Check for cracks or deformation
  • Look for signs of excessive wear
  • Verify proper fastener installation
2

Torque Verification

Verify the torque applied to the fasteners

  • Check the torque wrench calibration
  • Verify the torque specification
  • Compare the applied torque to the specification
3

Thread Assessment

Assess the condition of the threads

  • Check for signs of thread damage
  • Verify the thread type and size
  • Check for proper thread engagement

Prevention Guidelines

Best practices, maintenance tips, tool care

Best Practices

  • Always follow the recommended torque specification
  • Use the correct type and size of fasteners
  • Verify the torque wrench calibration regularly

Maintenance Tips

  • Regularly inspect the affected area for signs of wear or damage
  • Replace damaged or worn-out components promptly
  • Keep the work area clean and organized

Tool Care

  • Regularly clean and maintain the torque wrench
  • Store the torque wrench in a dry and secure location
  • Verify the torque wrench calibration before each use

Frequently Asked Questions

Find answers to common questions about torque specifications

Q1

What are the recommended torque values for lug nuts on a 2022-Present BMW m2?

120 Nm (89 ft-lbs) as per BMW specifications, refer to the vehicle owner's manual for specific details.

Q2

Can I use an impact wrench to tighten lug nuts on a BMW m2?

No, it IS not recommended to use an impact wrench on lug nuts, as overtightening can damage the threads or deform the nut.

Q3

What are the torque specifications for the brake caliper bolts on a 2022-Present BMW m2?

Front caliper bolts: 100 Nm (74 ft-lbs), Rear caliper bolts: 75 Nm (55 ft-lbs)

Q4

How often should I check the torque on my BMW m2's lug nuts?

It's recommended to check the torque on lug nuts every 1,000 miles or 1 month, especially after any tire service or rotation.

Q5

What IS the maximum torque I can apply to the oil drain plug on a BMW m2?

25 Nm (18 ft-lbs), overtightening can strip the threads or damage the oil pan.

Q6

Can I use a torque wrench to tighten the spark plugs on a BMW m2?

Yes, it IS recommended to use a torque wrench to tighten spark plugs to the specified torque of 22 Nm (16 ft-lbs).

Environmental Considerations

Temperature, humidity, and seasonal effects on torque specifications

Temperature Effects

Includes: High Heat, Cold Weather, Thermal Cycling

Temperature can significantly impact torque values and fastener behavior

Cold Weather

Effects:
  • Increased material brittleness
  • Higher torque required due to thread contraction
  • Reduced thread lubricant effectiveness
Recommendations:
  • Allow components to warm to room temperature when possible
  • Consider using winter-grade thread lubricants
  • Check torque values more frequently during winter months

Hot Weather

Effects:
  • Thermal expansion of components
  • Decreased friction in threads
  • Accelerated lubricant breakdown
Recommendations:
  • Check torque when components are at normal operating temperature
  • Use temperature-resistant thread lockers
  • Consider re-torquing after heat cycles

Humidity and Corrosion

Covers: Rust Prevention, Salt Exposure, Moisture Control

Moisture and corrosion can affect fastener integrity and torque values

High Humidity

Effects:
  • Accelerated corrosion formation
  • Reduced friction coefficient
  • Potential thread seizing
Prevention:
  • Use corrosion-resistant fasteners
  • Apply appropriate anti-seize compounds
  • Maintain proper protective coatings

Salt Exposure

Effects:
  • Rapid corrosion development
  • Thread damage
  • Seized fasteners
Prevention:
  • Regular underbody washing
  • Use of sacrificial anodes where appropriate
  • Application of protective coatings

Seasonal Maintenance

Spring, Summer, Fall, and Winter maintenance schedules

Spring

  • Inspect for winter damage
  • Clean and protect exposed fasteners
  • Check torque on critical components

Summer

  • Monitor heat-affected components
  • Check expansion-related loosening
  • Inspect cooling system mounts

Fall

  • Prepare for winter conditions
  • Apply corrosion protection
  • Verify all fasteners are properly torqued

Winter

  • More frequent inspection of critical fasteners
  • Check for salt damage
  • Monitor suspension component torque

Related Resources

Tools, service procedures, and technical bulletins

Recommended Tools

Digital Torque Wrench (10-200 Nm)

Recommended for precisely tightening m2 wheel bolts and lug nuts to specified torques, ensuring proper wheel mounting and safety. This range covers the typical torque requirements for BMW m2 wheels.

  • Digital display for accurate torque measurements
  • Audible and visual alerts indicate target torque achievement
  • Reversible ratcheting mechanism for ease of use
  • Compact and ergonomic design for convenient handling
Learn more
Service Procedures

Wheel Bolt Torque Procedure for the BMW m2

Step-by-step technical guidance on properly tightening wheel bolts on the BMW m2 to ensure optimal wheel mounting and safety.

  • Safety first: Engage the parking brake, ensure the vehicle IS on a stable surface, and use wheel chocks to prevent unexpected movement.
  • Locate the appropriate torque specification for your specific m2 model and wheel type; refer to the vehicle's owner's manual or BMW service documentation.
  • Clean the wheel bolts and threads to remove any dirt or debris that could affect torque accuracy.
  • Apply a small amount of anti-seize lubricant to the threads of the wheel bolts to prevent corrosion and aid in future removal.
  • Using the calibrated digital torque wrench, tighten each wheel bolt to the specified torque in a star pattern to ensure even distribution of force.
  • Double-check all tightened wheel bolts with the torque wrench to verify proper torque application.
  • Lower the vehicle and remove the wheel chocks, but avoid fully tightening the wheel bolts at this point.
  • Drive the vehicle for a short distance (approximately 100-200 km or 60-120 miles), allowing the wheels to settle.
  • Re-torque all wheel bolts to the specified torque using the digital torque wrench, following the same star pattern as before.
  • Record the torque values for future reference or if required for warranty purposes.
View full procedure
Technical Service Bulletins

BMW Service Bulletin: Wheel Bolt Torque Specifications for m2

2023-03-08

Official technical bulletin issued by BMW addressing specific wheel bolt torque specifications and tightening procedures for the BMW m2.

2022-Present m2

Resolution: Provides updated torque values and emphasizes the importance of adhering to proper tightening procedures to maintain optimal wheel mounting and safety.

Legal Disclaimer

Important information about using this content

Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.

General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability

The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.

We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.

Technical Information
  • All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
  • Vehicle specifications and procedures may vary by model year, trim level, and region.
  • Always follow the manufacturer's recommended procedures and safety precautions.
  • Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
  • If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.

About the Author

Expert automotive knowledge and experience

Alan Montanye - Automotive Technical Specialist
ASE

Alan Montanye

Automotive Technical Specialist

ASE Master Certified Technician with over a decade of hands-on experience in automotive repair and diagnostics.

Facebook Contact
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions

Diagnostic

Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.

Repair

Expert in both traditional mechanical repairs and modern vehicle systems.

Additional Expertise

Documentation

Created over 500 detailed repair guides and technical documents.

Training

Conducted technical training sessions and contributed to repair databases.

Certifications & Research

Certifications

  • ASE Master Technician Certification
  • Advanced Diagnostic Specialist
  • Hybrid/Electric Vehicle Systems
  • Performance Tuning Expert

Research & Community

Actively researches emerging technologies and contributes to automotive forums.

© 2025 BMW Specs. All rights reserved.

Privacy Policy Terms of Service