BMW Vehicle Models 760i 2009-2015 Torque Specifications
BMW Vehicle Models 760i 2009-2015

BMW Vehicle Models 760i 2009-2015 Torque Specifications

Complete BMW Vehicle Models 760i 2009-2015 torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.

Updated

Important Information

Safety guidelines and reference information for proper torque application

Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083

Common Torque Patterns

Star Pattern

Used for wheels and other circular bolt patterns

Star Pattern torque pattern diagram showing proper bolt tightening sequence
Cross Pattern

Used for gaskets and cover plates

Cross Pattern torque pattern diagram showing proper bolt tightening sequence
Sequential Pattern

Used for head bolts and other critical components

Sequential Pattern torque pattern diagram showing proper bolt tightening sequence

Common Mistakes to Avoid

Over-tightening

Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.

Prevention:

Always use a calibrated torque wrench and follow specifications exactly.

Incorrect Torque Sequence

Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.

Prevention:

Follow the manufacturer's specified torque sequence pattern.

Dirty Threads

Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.

Prevention:

Clean and inspect all threads before assembly. Use new thread locker if specified.

Reusing TTY Bolts

Torque-to-yield bolts are designed to stretch and must not be reused.

Prevention:

Always replace TTY bolts with new ones. They are single-use only.

Dry vs. Lubricated

Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.

Prevention:

Check if specs are for dry or lubricated threads. Use specified lubricant when required.

Recommended Tools

Torque Wrench (1/4" Drive)

Range: 2-25 ft-lbs
Small fasteners, delicate components

Torque Wrench (3/8" Drive)

Range: 10-100 ft-lbs
Most common automotive fasteners

Torque Wrench (1/2" Drive)

Range: 30-250 ft-lbs
Large fasteners, wheels

Angle Gauge

Torque-to-yield (TTY) bolts

Torque Wrench Care

  • Calibrate annually or after 5,000 clicks
  • Store at lowest setting
  • Keep clean and lubricated

Search Specifications

Search by component name, bolt size, or description

Torque Calculator

Convert between different torque units

6.0l Engine

Torque specifications for 6.0L Engine

Cylinder Head

1

Cylinder Head Bolts

M12 x 1.5
Torque Specification
1. 18 ft-lbs (25 N·m) 2. 90° 3. 90°
Important Notes
Initial torque followed by two angle-tightening stages. Consult the BMW workshop manual for the correct tightening sequence.
2

Valve Cover Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure proper gasket alignment before tightening.
3

Rocker Arms/Shafts Bolts

M8 x 1.25
Torque Specification
14 ft-lbs (19 N·m)
Important Notes
Tighten to specification to ensure proper valve train operation.
4

Camshaft Sprocket Bolt

M10 x 1.5
Torque Specification
58 ft-lbs (78 N·m)
Important Notes
Ensure proper camshaft timing alignment before tightening.

Engine Block

1

Main Bearing Bolts

M12 x 1.5
Torque Specification
1. 77 ft-lbs (105 N·m) 2. 90°
Important Notes
Initial torque followed by an angle-tightening stage. Consult the BMW workshop manual for the correct tightening sequence.
2

Connecting Rod Nuts

M9 x 1.25
Torque Specification
1. 22 ft-lbs (30 N·m) 2. 60°
Important Notes
Initial torque followed by an angle-tightening stage. Consult the BMW workshop manual for the correct tightening sequence.
3

Oil Pan Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Use a new gasket and tighten evenly to prevent leaks.
4

Oil Drain Plug Bolt

M14 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Use a new crush washer each time.
5

Crankshaft Position Sensor (CKP) Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure sensor is correctly seated before tightening.
6

Starter Motor Mounting Bolts

M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure correct alignment with the flywheel.

Intake System

1

Intake Manifold Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Tighten in a criss-cross pattern to ensure even clamping pressure.
2

Throttle Body Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Use a new gasket for proper sealing.
3

EGR Valve Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure the EGR valve gasket is properly aligned before tightening.

Exhaust System

1

Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Use new gaskets and tighten evenly to prevent leaks.

Fuel System

1

Fuel Rail Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure proper alignment to prevent fuel leaks.
2

Fuel Injector Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure proper injector sealing.

Ignition System

1

Spark Plugs

M14 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Use a torque wrench and new spark plugs when replacing.
2

Ignition Coil Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure coil is correctly seated before tightening.

Timing System

1

Timing Belt/Chain Tensioner Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper tensioner operation before tightening.

Cooling System

1

Water Pump Bolts

M8 x 1.25
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Use new gasket and tighten evenly to prevent coolant leaks.
2

Water Pump Pulley Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure correct pulley alignment.
3

Thermostat Housing Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Use new gasket for proper sealing.
4

Coolant Temperature Sensor Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure sensor is properly seated before tightening.
5

Coolant Drain Plug Torque

M12 x 1.5
Torque Specification
12 ft-lbs (16 N·m)
Important Notes
Use new sealing washer when possible.

Accessories

1

Crankshaft Pulley/Harmonic Balancer Bolt

M14 x 1.5
Torque Specification
96 ft-lbs (130 N·m)
Important Notes
Use correct torque for proper harmonic dampening.
2

Alternator Mounting Bolts

M10 x 1.5
Torque Specification
29 ft-lbs (40 N·m)
Important Notes
Ensure correct alignment with the drive belt.
3

A/C Compressor Mounting Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure correct alignment with the drive belt.

Sensors

1

Camshaft Position Sensor (CMP) Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the sensor is correctly seated before tightening.
2

Knock Sensor Bolt

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure sensor is properly seated before tightening.

6hp Transmission

Torque specifications for 6hp Transmission

Transmission Mounting

1

Transmission Mounting Bolts

M12 x 1.75
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper alignment of the transmission before tightening. May vary based on vehicle model, confirm in service manual.

Oil Pan

1

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Use a new gasket and tighten the bolts in a crisscross pattern. Over-tightening can damage the pan or gasket.

Drain Fill Plugs

1

Transmission Drain Plug

M16 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Use a new crush washer. Over-tightening can damage the plug or the transmission case.
2

Transmission Fill Plug

M16 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Use a new crush washer. Over-tightening can damage the plug or the transmission case.

Propeller Shaft

1

Propeller/Drive Shaft Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Use new bolts if specified. Tighten the bolts evenly to prevent vibrations.

Mechatronic Unit

1

Mechatronic Unit Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten bolts evenly in a crisscross pattern. Over-tightening can damage the unit or its seals.

Valve Body

1

Valve Body Mounting Bolts

M5 x 0.8
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Use a crisscross tightening pattern and ensure even pressure across the valve body.

Output Flange

1

Transmission Output Flange Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the driveshaft is correctly aligned before tightening. Use new bolts if specified.

Oil Cooler Lines

1

Transmission Oil Cooler Line Bolts

M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Use a backup wrench on the fitting when tightening the bolt to avoid twisting the line or fitting. Confirm if the line uses flared fittings, if so torque to 18 ft-lbs (24 N·m).

Housing

1

Transmission Housing Bolts

M12 x 1.75
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Use a crisscross tightening pattern, ensure that all bolts have proper thread engagement and apply even pressure when tightening. Torque may vary based on the location on the housing, check service manual.

Body

Torque specifications for Body

Door System

1

Door Hinge Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure proper door alignment before final tightening. Tighten evenly to prevent binding.

Exterior Panels

1

Fender Mounting Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Tighten evenly to maintain proper panel gaps.
2

Bumper Cover Mounting Bolts/Screws

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Do not over-tighten, as bumper covers are usually plastic.
3

Tail Light Mounting Bolts

M5 x 0.8
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Do not over-tighten as tail light housings are often fragile plastic. Tighten evenly.
4

Headlight Mounting Bolts

M5 x 0.8
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Do not over-tighten as headlight housings are often fragile plastic. Tighten evenly.

Hood System

1

Hood Hinge Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure proper hood alignment before final tightening. Tighten evenly.

Interior Components

1

Body Control Module Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Do not over-tighten. Ensure proper module seating.
2

Seat Mounting Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Critical safety component; use a calibrated torque wrench. Tighten evenly.
3

Seat Belt Anchor Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Critical safety component; use a calibrated torque wrench. Tighten evenly.
4

Interior Trim Panel Bolts/Screws

M4 x 0.7
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Do not over-tighten, as panels are typically plastic. Use a low torque setting.

Brakes

Torque specifications for Brakes

Caliper Mounting

1

Brake Caliper Bolts

M14 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Secures the caliper to the mounting bracket. Ensure proper thread engagement before tightening. Use a torque wrench and avoid over-tightening.
2

Brake Caliper Mounting Bracket Bolts

M16 x 1.5
Torque Specification
103 ft-lbs (140 N·m)
Important Notes
Attaches the caliper mounting bracket to the wheel hub or steering knuckle. These are critical bolts and must be torqued properly. Use a new bolt if there is any damage to the original.
3

Brake Pad Guide Pin Bolts/Screws (Front & Rear)

M8 x 1.25
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Secures the brake pads within the caliper. Replace bolts if they are damaged or appear worn. Estimated value, confirm with service manual. Some manufacturers may require new bolts, please refer to your vehicle's service manual.

Rotor Attachment

1

Brake Disc/Drum Retaining Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
These bolts hold the brake disc or drum onto the wheel hub. Do not over-tighten. Estimated value, confirm with service manual. Note: some brake rotors utilize a T screw. Be sure to use the correct torque specification for your specific vehicle.

Hydraulic Components

1

Brake Caliper Bleeder Screws (Rear and Front)

M7 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Used to remove air from brake lines. Do not over-tighten as it can damage the screw or the caliper. Estimated value, confirm with service manual.
2

Brake Hose to Caliper Banjo Bolt

M10 x 1.0
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Secures the brake line to the caliper. Use new crush washers when installing. Ensure correct torque to prevent leaks. Estimated value, confirm with service manual. Do not reuse old crush washers.
3

Brake Master Cylinder Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Attaches the master cylinder to the brake booster or firewall. Some bolts may require an additional angle. Estimated value, confirm with service manual.

Booster Mounting

1

Brake Booster Mounting Bolts to Firewall

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
These bolts secure the brake booster to the firewall. Ensure proper torque for safe brake function. Estimated value, confirm with service manual.
2

Brake Booster to Master Cylinder Mounting Nuts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
These nuts secure the master cylinder to the brake booster. Ensure a proper seal and function. Estimated value, confirm with service manual.

Parking Brake

1

Parking Brake Actuator Mounting Bolts

M6 x 1.0
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Secures the electric parking brake actuator to the caliper. Estimated value, confirm with service manual. Ensure correct torque for proper parking brake function.

Drivetrain

Torque specifications for Drivetrain

Engine Interface

1

Flywheel Bolts

M12 x 1.5
Torque Specification
96 ft-lbs (130 N·m)
Important Notes
Ensure bolts are clean and dry. Use a star pattern for tightening.

Transmission Mounting

1

Transmission Mounting Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Tighten bolts in a criss-cross pattern. Ensure proper alignment before final torquing.
2

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten in a criss-cross pattern to ensure even pressure on the pan gasket. Do not over-torque.
3

Transmission Output Flange Bolts

M10 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Ensure bolts are clean and dry.

Transmission Fluid Service

1

Transmission Fluid Drain/Fill Plugs

M18 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Use new crush washers. Do not over-torque.

Driveshaft

1

Propeller/Drive Shaft Bolts

M8 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure bolts are clean and dry.
2

Flex Disc/Guibo Bolts

M10 x 1.5
Torque Specification
40 ft-lbs (55 N·m)
Important Notes
Ensure bolts are clean and dry. Tighten evenly.

Drive Axle

1

Drive Axle/Half Shaft Bolts

M10 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Ensure proper alignment before final torquing. Tighten evenly.
2

CV Joint/Axle Nut

M24 x 1.5
Torque Specification
181 ft-lbs (245 N·m)
Important Notes
Ensure the nut is correctly seated on the CV joint/wheel hub. Use a new nut if required.

Differential

1

Differential Mounting Bolts

M12 x 1.75
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Tighten in a criss-cross pattern. Ensure proper alignment.
2

Differential Drain/Fill Plugs

M18 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Use new crush washers. Do not over-torque.
3

Rear Differential Cover Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Tighten bolts in a criss-cross pattern to ensure even pressure on the cover gasket. Do not over-torque.

Transfer Case

1

Transfer Case Mounting Bolts

M12 x 1.75
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Tighten bolts in a criss-cross pattern. Ensure proper alignment before final torquing. This is an estimated value.
2

Transfer Case Drain/Fill Plugs

M18 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Use new crush washers. Do not over-torque.

Electrical

Torque specifications for Electrical

Ignition System

1

Ignition Coil Mounting Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure proper coil alignment before tightening. Do not overtighten to prevent damage to the coil or valve cover.

Starting System

1

Starter Motor Mounting Bolt

M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the starter is properly aligned with the flywheel housing before tightening. Confirm the mounting surfaces are clean and free of debris.

Charging System

1

Alternator Mounting Bolt

M10 x 1.5
Torque Specification
29 ft-lbs (40 N·m)
Important Notes
Ensure correct alignment of the alternator before tightening. Check for proper belt tension after installation.

Battery System

1

Battery Terminal Nut

M8 x 1.25
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Do not overtighten. Use a backup wrench to avoid twisting the battery terminal. Ensure terminals are clean and free of corrosion.

Engine Control Unit

1

ECU Mounting Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure the ECU is properly aligned with the mounting points before tightening. Avoid over-tightening to prevent damage to the ECU case or mounting hardware.

Grounding System

1

Ground Strap/Cable Attachment Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure both contact surfaces are clean and free from corrosion for proper grounding. Multiple locations may exist.

Power Distribution

1

Fuse Box/Distribution Block Mounting Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Do not overtighten to avoid damage to the plastic housing. Confirm proper alignment of the fuse box or distribution block before tightening.

Sensor System

1

Crankshaft Position Sensor Mounting Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten carefully to avoid damaging the sensor housing. Ensure proper seating of the sensor.
2

Camshaft Position Sensor Mounting Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten carefully to avoid damaging the sensor housing. Ensure proper seating of the sensor.
3

MAF Sensor Mounting Bolt

M5 x 0.8
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure proper seating and alignment of the sensor within the intake path. Do not overtighten to avoid damaging the sensor or its housing.

Emissions Sensors

Torque specifications for Emissions_sensors

Exhaust System

1

Exhaust Manifold to Cylinder Head Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper alignment of the manifold before tightening. Use a new gasket.
2

Exhaust Manifold/Headers Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Apply medium-strength threadlocker. Use a new gasket.
3

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Use new gaskets and tighten evenly. Apply medium-strength threadlocker.
4

Muffler to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Use new gaskets, if applicable. Apply medium-strength threadlocker.
5

Oxygen (O2) Sensor Mounting Bolt

M10 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the sensor threads are clean. Do not overtighten to avoid damage.
6

NOx Sensor Mounting Bolts

M8 x 1.25
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Ensure proper alignment of the sensor before tightening. Apply medium-strength threadlocker.

Intake System

1

Mass Air Flow (MAF) Sensor Mounting Bolts

M5 x 0.8
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Do not overtighten to avoid damage to the sensor housing.
2

Intake Air Temperature (IAT) Sensor Mounting Screw

M4 x 0.7
Torque Specification
4 ft-lbs (5.5 N·m)
Important Notes
Tighten carefully to avoid damage. This is often a screw, not a bolt.

Egr System

1

EGR Valve Mounting Bolts

M8 x 1.25
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Use a new gasket and ensure proper alignment. Apply medium-strength threadlocker.

Dpf System

1

Differential Pressure Sensor (DPF) Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure the sensor is properly seated before tightening.

Evap System

1

Evaporative Emission (EVAP) Canister Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure the canister is properly positioned.
2

Evaporative Emission (EVAP) Purge Valve Mounting Bolts

M5 x 0.8
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Do not overtighten to prevent damage to the valve.

Exhaust

Torque specifications for Exhaust

Exhaust Manifold

1

Exhaust Manifold/Header to Cylinder Head Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Apply a cross-pattern torque sequence to ensure even pressure. Initial tightening should be in several stages. Final torque is 18 ft-lbs / 25 N·m

Exhaust Pipes

1

Exhaust Pipe to Exhaust Manifold/Headers Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper alignment before tightening. Use new gaskets if needed.
2

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper alignment before tightening. Use new gaskets if needed.
3

Muffler to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper alignment before tightening. Use new gaskets if needed.

Exhaust Clamps

1

Small Exhaust Clamp Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated value based on common small clamp sizes. Do not overtighten. Check manufacturer's specifications on clamp.
2

Medium Exhaust Clamp Bolts

M8 x 1.25
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Estimated value based on common medium clamp sizes. Do not overtighten. Check manufacturer's specifications on clamp.
3

Large Exhaust Clamp Bolts

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Estimated value based on common large clamp sizes. Do not overtighten. Check manufacturer's specifications on clamp.

Fuel

Torque specifications for Fuel

Fuel Rail

1

Fuel Rail Mounting Bolts

M8 x 1.25
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensures proper fuel rail sealing and prevents leaks. Do not over-tighten.
2

Fuel Pressure Sensor Mounting Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Secures the fuel pressure sensor to the fuel rail. Ensure o-ring or crush washer is properly installed and lubricated.

Fuel Injectors

1

Fuel Injector Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Secures the fuel injectors to the intake manifold or cylinder head. Do not overtighten to prevent damage to injector seals.

Fuel Pump

1

Fuel Pump Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Secures the fuel pump assembly to the fuel tank. Ensure that any sealing gaskets are in good condition and positioned correctly.
2

High-Pressure Fuel Pump Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Secures the high-pressure fuel pump to the engine block or cylinder head. Proper torque is critical to prevent leaks.
3

Fuel Tank Sending Unit Lock Ring

N/A
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
This is an estimated torque value for the lock ring. Use a suitable tool to achieve this torque. Ensure a proper seal, do not overtighten. Estimated Value.

Fuel Lines

1

Fuel Line Connection Fittings/Banjo Bolts

Varies (M10 x 1.0, M12 x 1.5)
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Estimated value, actual torque depends on the specific fitting size and type (banjo, compression, flared). Always replace sealing washers. Estimated Value.

Fuel Filter

1

Fuel Filter Mounting Bolt/Nut

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Secures the fuel filter bracket and the fuel filter itself. Do not overtighten to prevent damage.

Fuel Filler Neck

1

Fuel Filler Neck Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Secures the filler neck to the vehicle body or fuel tank. Ensures a proper seal to prevent fuel leaks and fumes. Do not overtighten.

Hvac

Torque specifications for Hvac

Ac Compressor

1

A/C Compressor Mounting Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper alignment of the compressor before tightening. Use new bolts if specified by the manufacturer.

Ac Lines

1

A/C Line Fittings

M8 x 1.25
Torque Specification
14 ft-lbs (19 N·m)
Important Notes
Do not overtighten; this can damage seals and fittings. Use a flare nut wrench when possible. Ensure that o-rings are in good condition before tightening.

Ac Condenser

1

A/C Condenser Mounting Bolts/Nuts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Estimated value based on typical fasteners for this application. Do not overtighten. Often securing to sheetmetal.
2

A/C Condenser Bracket Bolts

M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Estimated value based on typical fasteners for this application. Do not overtighten. Often securing to the radiator support.

Ac Evaporator

1

A/C Evaporator Housing Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
These are typically small bolts securing plastic components. Do not overtighten. Estimated value based on similar applications.

Hvac Control Module

1

HVAC Control Module Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Typically small bolts securing the module to the dash assembly. Estimated value based on similar applications.

Blower Motor

1

Blower Motor Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated value. Do not overtighten. Often securing plastic housings.

Heater Core

1

Heater Core Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated value, similar to evaporator housing. Typically small bolts securing plastic components. Do not overtighten.

Blend Door Actuator

1

HVAC Blend Door Actuator Bolts

M5 x 0.8
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Estimated value. Small bolts securing plastic actuators. Do not overtighten.

Mode Door Actuator

1

HVAC Mode Door Actuator Bolts

M5 x 0.8
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Estimated value. Small bolts securing plastic actuators. Do not overtighten.

Ac Pressure Sensor

1

A/C Pressure Sensor

Schrader Valve Fitting
Torque Specification
0.7 ft-lbs (1 N·m)
Important Notes
Hand tight + 1/8 turn using a wrench. Typically a Schrader valve fitting. Estimated torque based on similar fittings.

Suspension

Torque specifications for Suspension

Front Strut Assembly

1

Strut Upper Mounting Bolts

M10 x 1.5
Torque Specification
96 ft-lbs (130 N·m)
Important Notes
Secures the upper strut mount to the vehicle chassis.
2

Strut Lower Mounting Bolts

M14 x 1.5
Torque Specification
1. 81 ft-lbs (110 N·m) 2. 90°
Important Notes
Secures the lower strut mount to the wheel bearing housing/knuckle. This is a stretch bolt and requires a torque and angle procedure.

Front Control Arms

1

Lower Control Arm Bolts

M14 x 1.5
Torque Specification
103 ft-lbs (140 N·m)
Important Notes
Connects the control arm to the vehicle's frame or subframe and to the wheel hub/knuckle.
2

Upper Control Arm Bolts

M12 x 1.5
Torque Specification
1. 74 ft-lbs (100 N·m) 2. 90°
Important Notes
Connects the upper control arm to the vehicle's frame or subframe and to the wheel hub/knuckle. This is a stretch bolt and requires a torque and angle procedure.
3

Ball Joint Nut

M12 x 1.25
Torque Specification
48 ft-lbs (65 N·m)
Important Notes
Secures the ball joint stud to the control arm or steering knuckle.

Steering Components

1

Tie Rod End Nut

M12 x 1.25
Torque Specification
48 ft-lbs (65 N·m)
Important Notes
Fastens the tie rod end to the steering knuckle or the tie rod itself.

Sway Bar System

1

Sway Bar Link Nut

M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Secures the sway bar links to the sway bar and the strut/control arm.
2

Sway Bar Bracket Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Mounts the sway bar to the chassis or subframe.

Subframe Mounting

1

Subframe Mounting Bolts

M14 x 2.0
Torque Specification
1. 70 ft-lbs (95 N·m) 2. 90°
Important Notes
Secures the subframe to the vehicle's chassis. This is a stretch bolt and requires a torque and angle procedure.

Sensor Mounting

1

Wheel Speed Sensor Mounting Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Secures the wheel speed sensor to the hub or knuckle.

Troubleshooting Guide

Common issues, diagnostic steps, and prevention guidelines

Common Issues

Bolt stretching, stripped threads, uneven torque patterns

Loose Components

Symptoms:
  • Rattling or vibration noises
  • Visible movement in components
  • Uneven panel gaps
Solutions:
  • Clean threads and mounting surfaces
  • Replace damaged fasteners
  • Apply proper torque in sequence
  • Use thread locker if specified

Stripped Fasteners

Symptoms:
  • Unable to achieve proper torque
  • Fastener spins freely
  • Visible thread damage
Solutions:
  • Use thread repair kit if appropriate
  • Install thread insert (HeliCoil)
  • Replace component if threaded hole is damaged
  • Upgrade to higher grade fastener if recommended

Overtightened Components

Symptoms:
  • Cracked or deformed parts
  • Broken fasteners
  • Compressed gaskets or seals
Solutions:
  • Replace damaged components
  • Use new fasteners
  • Follow proper torque sequence
  • Verify correct torque specifications

Diagnostic Steps

Visual inspection, torque verification, thread assessment

1

Visual Inspection

Inspect the affected area for any visible signs of damage or wear

  • Check for cracks or deformation
  • Look for signs of excessive wear
  • Verify proper fastener installation
2

Torque Verification

Verify the torque applied to the fasteners

  • Check the torque wrench calibration
  • Verify the torque specification
  • Compare the applied torque to the specification
3

Thread Assessment

Assess the condition of the threads

  • Check for signs of thread damage
  • Verify the thread type and size
  • Check for proper thread engagement

Prevention Guidelines

Best practices, maintenance tips, tool care

Best Practices

  • Always follow the recommended torque specification
  • Use the correct type and size of fasteners
  • Verify the torque wrench calibration regularly

Maintenance Tips

  • Regularly inspect the affected area for signs of wear or damage
  • Replace damaged or worn-out components promptly
  • Keep the work area clean and organized

Tool Care

  • Regularly clean and maintain the torque wrench
  • Store the torque wrench in a dry and secure location
  • Verify the torque wrench calibration before each use

Frequently Asked Questions

Find answers to common questions about torque specifications

Q1

What IS the recommended torque for the engine head bolts on a 2010 BMW 760i?

44 ft-lbs (60 Nm) in two stages, then an additional 90 degrees.

Q2

Which torque wrench should I use for critical engine components on my 2015 BMW 760i?

Use a calibrated, click-type torque wrench that meets or exceeds BMW's specifications.

Q3

IS there a specific tightening sequence for the intake manifold bolts on a 2012 BMW 760i?

Yes, follow the sequence outlined in the BMW repair manual, starting from the center and working outwards in a star pattern.

Q4

What IS the torque specification for the wheel lug bolts on a 2009 BMW 760i?

110 ft-lbs (150 Nm) using a calibrated torque wrench.

Q5

Can I use anti-seize compound on the spark plugs when reinstalling them in my 2013 BMW 760i?

No, anti-seize compound should not be used on spark plugs as it can affect torque accuracy and lead to engine damage.

Q6

What IS the proper torque for the crankshaft pulley bolt on a 2014 BMW 760i?

250 ft-lbs (340 Nm) in a clockwise direction. Use a new bolt and torque to specification.

Environmental Considerations

Temperature, humidity, and seasonal effects on torque specifications

Temperature Effects

Includes: High Heat, Cold Weather, Thermal Cycling

Temperature can significantly impact torque values and fastener behavior

Cold Weather

Effects:
  • Increased material brittleness
  • Higher torque required due to thread contraction
  • Reduced thread lubricant effectiveness
Recommendations:
  • Allow components to warm to room temperature when possible
  • Consider using winter-grade thread lubricants
  • Check torque values more frequently during winter months

Hot Weather

Effects:
  • Thermal expansion of components
  • Decreased friction in threads
  • Accelerated lubricant breakdown
Recommendations:
  • Check torque when components are at normal operating temperature
  • Use temperature-resistant thread lockers
  • Consider re-torquing after heat cycles

Humidity and Corrosion

Covers: Rust Prevention, Salt Exposure, Moisture Control

Moisture and corrosion can affect fastener integrity and torque values

High Humidity

Effects:
  • Accelerated corrosion formation
  • Reduced friction coefficient
  • Potential thread seizing
Prevention:
  • Use corrosion-resistant fasteners
  • Apply appropriate anti-seize compounds
  • Maintain proper protective coatings

Salt Exposure

Effects:
  • Rapid corrosion development
  • Thread damage
  • Seized fasteners
Prevention:
  • Regular underbody washing
  • Use of sacrificial anodes where appropriate
  • Application of protective coatings

Seasonal Maintenance

Spring, Summer, Fall, and Winter maintenance schedules

Spring

  • Inspect for winter damage
  • Clean and protect exposed fasteners
  • Check torque on critical components

Summer

  • Monitor heat-affected components
  • Check expansion-related loosening
  • Inspect cooling system mounts

Fall

  • Prepare for winter conditions
  • Apply corrosion protection
  • Verify all fasteners are properly torqued

Winter

  • More frequent inspection of critical fasteners
  • Check for salt damage
  • Monitor suspension component torque

Related Resources

Tools, service procedures, and technical bulletins

Recommended Tools

Hazet Digital Torque Wrench 6729-1CT

Digital torque wrench designed for precision and accuracy with a range of 10-100 Nm, suitable for various applications on the 760I.

  • Calibrated to DIN EN ISO 6789-1:2017
  • Digital display with backlit LCD screen for easy reading
  • Ratcheting head for increased efficiency
  • Peak hold function to capture maximum torque achieved
Learn more

CDI Torque Angle Gauge TG400

Compact and precise torque angle gauge for accurate tightening of fasteners requiring specific rotation angles.

  • Measures torque and angle simultaneously
  • Easy-to-read digital display
  • Compact design for confined spaces
  • Memory function to store and recall previous measurements
Learn more
Service Procedures

Cylinder Head Bolt Torque Procedure

Step-by-step procedure for tightening cylinder head bolts to specified torque values.

  • Remove the cylinder head cover.
  • Clean and inspect the cylinder head bolts and bolt holes.
  • Lubricate the bolt threads with engine oil.
  • Tighten the bolts in the correct sequence and to the specified torque using a digital torque wrench.
View full procedure

Suspension Component Torque Procedure

Procedure for tightening suspension components, including control arms, ball joints, and tie rods.

  • Raise the vehicle and support it securely on jack stands.
  • Remove the wheel and tire assembly.
  • Clean and inspect the suspension components and fasteners.
  • Tighten the fasteners to the specified torque using a digital torque wrench.
View full procedure
Technical Service Bulletins

Engine Timing Chain Tensioner Replacement

2013-03-01

Technical bulletin outlining a revised procedure for replacing the engine timing chain tensioner.

2009-2015 760I

Resolution: Updated torque specifications for the timing chain tensioner bolts.

Front Brake Rotor Replacement

2015-07-15

Technical bulletin providing revised torque specifications for the front brake rotor retaining screws.

2009-2015 760I

Resolution: Updated torque specifications to prevent rotor warping and ensure proper braking performance.

Legal Disclaimer

Important information about using this content

Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.

General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability

The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.

We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.

Technical Information
  • All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
  • Vehicle specifications and procedures may vary by model year, trim level, and region.
  • Always follow the manufacturer's recommended procedures and safety precautions.
  • Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
  • If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.

About the Author

Expert automotive knowledge and experience

Alan Montanye - Automotive Technical Specialist
ASE

Alan Montanye

Automotive Technical Specialist

ASE Master Certified Technician with over a decade of hands-on experience in automotive repair and diagnostics.

Facebook Contact
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions

Diagnostic

Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.

Repair

Expert in both traditional mechanical repairs and modern vehicle systems.

Additional Expertise

Documentation

Created over 500 detailed repair guides and technical documents.

Training

Conducted technical training sessions and contributed to repair databases.

Certifications & Research

Certifications

  • ASE Master Technician Certification
  • Advanced Diagnostic Specialist
  • Hybrid/Electric Vehicle Systems
  • Performance Tuning Expert

Research & Community

Actively researches emerging technologies and contributes to automotive forums.

© 2025 BMW Specs. All rights reserved.

Privacy Policy Terms of Service