BMW Vehicle Models 750i 2008-2015 Torque Specifications
BMW Vehicle Models 750i 2008-2015

BMW Vehicle Models 750i 2008-2015 Torque Specifications

Complete BMW Vehicle Models 750i 2008-2015 torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.

Updated

Important Information

Safety guidelines and reference information for proper torque application

Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083

Common Torque Patterns

Star Pattern

Used for wheels and other circular bolt patterns

Star Pattern torque pattern diagram showing proper bolt tightening sequence
Cross Pattern

Used for gaskets and cover plates

Cross Pattern torque pattern diagram showing proper bolt tightening sequence
Sequential Pattern

Used for head bolts and other critical components

Sequential Pattern torque pattern diagram showing proper bolt tightening sequence

Common Mistakes to Avoid

Over-tightening

Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.

Prevention:

Always use a calibrated torque wrench and follow specifications exactly.

Incorrect Torque Sequence

Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.

Prevention:

Follow the manufacturer's specified torque sequence pattern.

Dirty Threads

Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.

Prevention:

Clean and inspect all threads before assembly. Use new thread locker if specified.

Reusing TTY Bolts

Torque-to-yield bolts are designed to stretch and must not be reused.

Prevention:

Always replace TTY bolts with new ones. They are single-use only.

Dry vs. Lubricated

Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.

Prevention:

Check if specs are for dry or lubricated threads. Use specified lubricant when required.

Recommended Tools

Torque Wrench (1/4" Drive)

Range: 2-25 ft-lbs
Small fasteners, delicate components

Torque Wrench (3/8" Drive)

Range: 10-100 ft-lbs
Most common automotive fasteners

Torque Wrench (1/2" Drive)

Range: 30-250 ft-lbs
Large fasteners, wheels

Angle Gauge

Torque-to-yield (TTY) bolts

Torque Wrench Care

  • Calibrate annually or after 5,000 clicks
  • Store at lowest setting
  • Keep clean and lubricated

Search Specifications

Search by component name, bolt size, or description

Torque Calculator

Convert between different torque units

4.4l Engine

Torque specifications for 4.4L Engine

Cylinder Head

1

Cylinder Head Bolts

M12 x 1.75
Torque Specification
1. 16 ft-lbs (22 N·m) 2. 90° 3. 90°
Important Notes
Cylinder head bolts are torque-to-yield (TTY) and must be replaced. Use a new set and follow proper tightening sequence. First torque in sequence to specified value, then rotate each bolt to the specified angle.

Main Bearing

1

Main Bearing Bolts

M10 x 1.5
Torque Specification
1. 22 ft-lbs (30 N·m) 2. 70°
Important Notes
Main bearing bolts often require an angle torque procedure after initial torque. Follow the correct tightening sequence. Bolts are TTY and should be replaced.

Connecting Rod

1

Connecting Rod Nuts

M9 x 1.25
Torque Specification
1. 15 ft-lbs (20 N·m) 2. 60°
Important Notes
Connecting rod bolts are often torque-to-yield and need to be replaced. Use a new set and follow the tightening sequence and torque angle.

Flywheel

1

Flywheel Bolts

M12 x 1.5
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Always use new flywheel bolts when reassembling. Tighten in a star pattern for even clamping.

Oil Pan

1

Oil Pan Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten bolts evenly in a criss-cross pattern. Be careful not to overtighten and damage the pan.

Valve Cover

1

Valve Cover Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten evenly in a criss-cross pattern, be careful not to overtighten or you might damage the cover or gasket.

Timing Components

1

Timing Chain Tensioner Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper timing chain tension before tightening.
2

Camshaft Sprocket Bolts

M10 x 1.5
Torque Specification
63 ft-lbs (85 N·m)
Important Notes
Ensure proper alignment of the sprockets before tightening

Crankshaft

1

Crankshaft Pulley/Harmonic Balancer Bolt

M14 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Ensure proper pulley alignment before tightening.

Intake System

1

Throttle Body Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten evenly to ensure a proper seal.
2

Intake Manifold Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Tighten in the proper sequence to ensure even sealing and to prevent vacuum leaks.

Exhaust System

1

Exhaust Manifold/Headers to Cylinder Head Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Tighten in the proper sequence from center to outer bolts to avoid leaks.

Valve Train

1

Rocker Arms/Shafts Bolts

M8 x 1.25
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten evenly and ensure rocker arms move freely.
2

Camshaft Bearing Cap Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten in proper sequence to avoid camshaft binding or damage. Estimated value.

Ignition System

1

Spark Plugs

M14 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Do not overtighten the spark plugs to prevent thread damage.
2

Ignition Coil Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten evenly. Do not overtighten, or you might damage the coil.

Fuel System

1

Fuel Injector Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten evenly. Ensure injectors are seated properly to prevent fuel leaks.
2

Fuel Injector Rail Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten evenly. Ensure that the fuel rail sits securely.

Cooling System

1

Water Pump Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Tighten evenly. Ensure proper seal to prevent leaks.
2

Water Pump Pulley Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten evenly. Ensure proper pulley alignment.
3

Thermostat Housing Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten evenly. Ensure a proper seal to prevent leaks.

Belt Drive System

1

Serpentine/Accessory Drive Belt Tensioner Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper tensioner alignment. Do not overtighten.

Oil System

1

Oil Filter Housing Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure a proper seal to prevent oil leaks.
2

Oil Drain Plug Bolt

M14 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Use a new washer. Do not overtighten.

Engine Accessories

1

Starter Motor Mounting Bolts

M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper alignment of the starter.
2

Alternator Mounting Bolts

M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper alignment of the alternator. Do not overtighten.
3

A/C Compressor Mounting Bolts

M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper alignment of the compressor. Do not overtighten.
4

Power Steering Pump Mounting Bolts

M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper alignment of the power steering pump. Do not overtighten.

Variable Valve Timing

1

Variable Valve Timing (VANOS) Solenoid Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten evenly and be careful not to overtighten. Estimated value.

Sensors

1

Knock Sensor Bolts

M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Ensure the sensor is properly seated to obtain accurate readings. Estimated value.

6hp Transmission

Torque specifications for 6hp Transmission

Transmission Mounting

1

Transmission Mounting Bolts

M12 x 1.75
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Tighten in a cross pattern to ensure even pressure and correct alignment.

Transmission Oil Pan

1

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Use a new gasket to prevent leaks. Tighten in a cross pattern.

Transmission Plugs

1

Transmission Drain and Fill Plugs

M18 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Overtightening can strip threads in the transmission case. Use new sealing washers.

Mechatronic Unit

1

Mechatronic Unit Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten in a cross pattern. Use care when tightening.
2

Valve Body Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten in a cross pattern. This spec is if the valve body is separated from the mechatronic unit, which is not a usual repair.

Transmission Housing

1

Transmission Housing Bolts

M10 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Tighten in a cross pattern to ensure even pressure and proper sealing.

Torque Converter

1

Torque Converter Bolts

M10 x 1.25
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Tighten in a star pattern, alternating bolts for even pressure.

Output Shaft

1

Output Shaft Flange Bolt/Nut

M14 x 1.5
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Use new fasteners if recommended by the manufacturer.

Body

Torque specifications for Body

Fuel System

1

Fuel Tank Strap Bolts

M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Secures fuel tank straps to the vehicle underbody. Ensure proper alignment before tightening.
2

Fuel Filler Neck Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Attaches the fuel filler neck to the vehicle body. Ensure proper sealing with a gasket or sealant.

Wheel System

1

Wheel Lug Nuts

M12 x 1.5
Torque Specification
103 ft-lbs (140 N·m)
Important Notes
Secures the wheel to the hub. Torque in a star pattern to ensure even clamping force.

Door System

1

Door Hinge Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Attaches door hinges to the vehicle body and door. Ensure proper door alignment before final torque. Estimated value, confirm with vehicle-specific manual.
2

Door Latch/Striker Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Secures door latches and strikers to the body. Ensure correct latching and door alignment. Estimated value, confirm with vehicle-specific manual.

Exterior Panels

1

Fender Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Fastens fenders to the vehicle body. Do not over-tighten to prevent damage to sheet metal. Estimated value, confirm with vehicle-specific manual.
2

Bumper Mounting Bolts (Front/Rear)

M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Connects the bumper assembly to the vehicle's frame. Ensure even torque distribution. Estimated value, confirm with vehicle-specific manual.
3

Grille Mounting Bolts/Screws

M5 x 0.8
Torque Specification
4 ft-lbs (5.4 N·m)
Important Notes
Secures the grille to the vehicle body. Do not over-tighten to prevent damage to plastic. Estimated value, confirm with vehicle-specific manual.

Hood System

1

Hood Hinge Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Attaches hood hinges to the vehicle body and hood. Ensure proper hood alignment before final torque. Estimated value, confirm with vehicle-specific manual.
2

Hood Latch/Striker Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Secures hood latch and striker to the body. Ensure correct hood closure. Estimated value, confirm with vehicle-specific manual.

Lighting System

1

Headlight Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the headlight assembly to the vehicle body. Ensure proper alignment. Estimated value, confirm with vehicle-specific manual.
2

Taillight Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the taillight assembly to the vehicle body. Ensure proper alignment. Estimated value, confirm with vehicle-specific manual.

Mirror System

1

Side Mirror Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the side mirror assembly to the vehicle body. Do not over-tighten to prevent damage. Estimated value, confirm with vehicle-specific manual.

Roof System

1

Sunroof/Moonroof Mounting Bolts

M5 x 0.8
Torque Specification
4 ft-lbs (5.4 N·m)
Important Notes
Secures the sunroof/moonroof assembly to the vehicle roof. Do not over-tighten to avoid damage. Estimated value, confirm with vehicle-specific manual.

Interior System

1

Seat Mounting Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Secures seats to the vehicle floor pan. These are critical safety components. Ensure correct bolt size and type. Estimated value, confirm with vehicle-specific manual.
2

Dashboard/Instrument Panel Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Secures the dashboard to the vehicle body structure. Estimated value, confirm with vehicle-specific manual.
3

Rear Deck/Package Tray Mounting Bolts/Screws

M5 x 0.8
Torque Specification
4 ft-lbs (5.4 N·m)
Important Notes
Secures rear deck/package tray trim to the vehicle body. Do not over-tighten to prevent damage. Estimated value, confirm with vehicle-specific manual.
4

Interior Trim Panel Mounting Clips/Bolts/Screws

Clip/Screw
Torque Specification
2 ft-lbs (3 N·m)
Important Notes
Secures interior trim panels to the vehicle body. Generally hand tight or very low torque. Over-tightening can damage trim. Estimated value, confirm with vehicle-specific manual.
5

Vehicle Name/Emblem Mounting Fasteners

Clip/Adhesive
Torque Specification
2 ft-lbs (3 N·m)
Important Notes
Secures vehicle name/emblems to the vehicle body. Generally hand tight or very low torque. Over-tightening can damage emblems. Estimated value, confirm with vehicle-specific manual.

Brakes

Torque specifications for Brakes

Front Brake Caliper

1

Front Caliper Mounting Bolts

M12 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Torque bolts evenly to ensure proper clamping force. Always use a calibrated torque wrench.
2

Front Brake Pad Guide Pin Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure guide pins are clean and lightly lubricated. Do not over-torque.
3

Front Caliper Bleeder Screw

M10 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Do not over-tighten. Proper sealing is crucial. Use a flare nut wrench.
4

Front Brake Hose Banjo Bolt (Caliper Side)

M10 x 1.0
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Always use new copper washers. Ensure the banjo fitting is correctly aligned.

Front Brake Caliper Bracket

1

Front Caliper Mounting Bracket Bolts

M14 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Ensure proper alignment. Use new bolts if previously over-torqued.

Front Brake Rotor

1

Front Brake Rotor Retaining Bolt

M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
This is an estimated value. Verify with a specific service manual. Usually only one retaining screw is present.

Rear Brake Caliper

1

Rear Caliper Mounting Bolts

M12 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Torque bolts evenly to ensure proper clamping force. Always use a calibrated torque wrench.
2

Rear Brake Pad Guide Pin Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure guide pins are clean and lightly lubricated. Do not over-torque.
3

Rear Caliper Bleeder Screw

M10 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Do not over-tighten. Proper sealing is crucial. Use a flare nut wrench.
4

Rear Brake Hose Banjo Bolt (Caliper Side)

M10 x 1.0
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Always use new copper washers. Ensure the banjo fitting is correctly aligned.

Rear Brake Caliper Bracket

1

Rear Caliper Mounting Bracket Bolts

M14 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Ensure proper alignment. Use new bolts if previously over-torqued.

Rear Brake Rotor

1

Rear Brake Rotor Retaining Bolt

M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
This is an estimated value. Verify with a specific service manual. Usually only one retaining screw is present.

Brake Hoses And Lines

1

Brake Hose Banjo Bolt (Chassis/Line Side)

M10 x 1.0
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Always use new copper washers. Ensure the banjo fitting is correctly aligned.
2

Brake Line Flare Nut

M10 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Use a flare nut wrench to prevent damage. Torque is estimated, verify with a model specific service manual.

Brake Master Cylinder

1

Brake Master Cylinder Mounting Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Tighten evenly to ensure proper contact with the brake booster. Torque is estimated, verify with a model specific service manual.

Brake Booster

1

Brake Booster Mounting Nuts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Tighten evenly. Torque is estimated, verify with a model specific service manual.

Drivetrain

Torque specifications for Drivetrain

Engine Flywheel

1

Flywheel Bolts

M12 x 1.5
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Use new bolts. Tighten in a star pattern to ensure even clamping pressure. Apply a small amount of engine oil to bolt threads.
2

Flexplate Bolts

M12 x 1.5
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Use new bolts. Tighten in a star pattern to ensure even clamping pressure. Apply a small amount of engine oil to bolt threads.
3

Torque Converter Bolts

M10 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
These bolts connect the torque converter to the flexplate. Tighten evenly and carefully. Apply a small amount of engine oil to bolt threads.

Transmission Mounting

1

Transmission Mounting Bolts

M12 x 1.75
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper alignment of the transmission before tightening. Apply a small amount of anti-seize to the bolt threads.
2

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten these bolts evenly and in a crisscross pattern to prevent leaks. Do not overtighten, or you can cause damage to the transmission pan.
3

Transmission Drain and Fill Plugs

M18 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Use new crush washers for a proper seal. Do not overtighten, or you may damage the transmission case.

Driveshaft

1

Propeller/Drive Shaft Bolts

M10 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Tighten all bolts evenly, and use new bolts when possible. May require a special tool for proper access, and these bolts are likely to be torqued in a star pattern.
2

Center Support Bearing Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the bearing is correctly positioned before tightening these bolts. Apply a small amount of anti-seize to the bolt threads.

Axle And Cv Joints

1

Drive Axle/Half Shaft Bolts

M12 x 1.5
Torque Specification
147 ft-lbs (200 N·m)
Important Notes
These bolts connect the drive axle to the transmission or differential flange. Always double check for proper torque.
2

Rear Drive Axle Flange Bolts

M10 x 1.5
Torque Specification
60 ft-lbs (80 N·m)
Important Notes
These bolts connect the axle shaft to the rear differential flange. Ensure the bolts are properly aligned, and use new hardware if it has any indication of damage. Tighten in a star pattern to ensure even clamping pressure.
3

CV Joint/Axle Nut

M24 x 1.5
Torque Specification
129 ft-lbs (175 N·m)
Important Notes
This is the main nut securing the CV joint to the wheel hub. Use new hardware when possible, and ensure proper torque is achieved.

Differential

1

Differential Mounting Bolts

M12 x 1.75
Torque Specification
60 ft-lbs (80 N·m)
Important Notes
These bolts secure the differential to the vehicle's chassis or subframe. Ensure proper alignment before tightening. This is an estimated value; refer to the service manual for your specific vehicle.
2

Differential Drain/Fill Plugs

M18 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Use new crush washers for a proper seal. Ensure the drain and fill plugs are clean and properly threaded. Do not overtighten, or you may damage the case.

Transfer Case

1

Transfer Case Drain/Fill Plugs

M18 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Use new crush washers for a proper seal. Ensure the plugs are clean and properly threaded. Do not overtighten, or you may damage the case.

Electrical

Torque specifications for Electrical

Ignition System

1

Spark Plugs

M14 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the spark plug threads are clean and lightly lubricated with anti-seize compound before installation. Over-tightening can damage cylinder head threads. Insufficient torque may cause a poor electrical ground and poor heat transfer, causing misfires.
2

Ignition Coil Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the coil is properly seated before tightening. Over-tightening can damage the coil or its mounting points.

Starting Charging System

1

Starter Motor Mounting Bolts

M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the starter motor is properly aligned before tightening. Incorrect torque may lead to poor grounding and misalignment. Tighten evenly to ensure proper seating.
2

Alternator Mounting Bolts

M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper belt alignment after installation. Incorrect torque can cause pulley misalignment and vibrations, which can cause damage and charging system failures.

Battery System

1

Battery Terminal Nuts

M8 x 1.25
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure the terminals are clean before tightening. Over-tightening can damage the battery terminals. Insufficient torque can cause poor connections leading to heat buildup, corrosion or fire. Apply dielectric grease after tightening.

Engine Control System

1

Engine Control Unit (ECU) Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the ECU is properly positioned before tightening. Over-tightening can damage the ECU housing. Avoid excessive vibration for reliable electronic performance.
2

Crankshaft Position Sensor Mounting Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the sensor is correctly seated before tightening the bolt. Incorrect torque could lead to inaccurate readings or sensor damage.
3

Camshaft Position Sensor Mounting Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the sensor is correctly seated before tightening the bolt. Incorrect torque could lead to inaccurate readings or sensor damage.

Grounding System

1

Ground Strap/Cable Mounting Bolts (M6)

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the ground points are clean and free of corrosion before tightening. Over-tightening can damage the mounting location, or cause the cable to fail. Insufficient torque can cause a poor ground connection, causing electrical issues.
2

Ground Strap/Cable Mounting Bolts (M8)

M8 x 1.25
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Ensure the ground points are clean and free of corrosion before tightening. Over-tightening can damage the mounting location, or cause the cable to fail. Insufficient torque can cause a poor ground connection, causing electrical issues.
3

Ground Strap/Cable Mounting Bolts (M10)

M10 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the ground points are clean and free of corrosion before tightening. Over-tightening can damage the mounting location, or cause the cable to fail. Insufficient torque can cause a poor ground connection, causing electrical issues.

Power Distribution

1

Fuse Box/Power Distribution Box Mounting Bolts (M6)

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the box is properly aligned before tightening. Over-tightening can damage the plastic housing. Secure mounting ensures proper electrical integrity.
2

Fuse Box/Power Distribution Box Mounting Bolts (M8)

M8 x 1.25
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Ensure the box is properly aligned before tightening. Over-tightening can damage the plastic housing. Secure mounting ensures proper electrical integrity.

Body Control

1

Body Control Module (BCM) Mounting Bolts

M5 x 0.8
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Ensure the BCM is properly positioned before tightening. Over-tightening can damage the BCM housing. Secure mounting minimizes vibration.
2

Headlight/Taillight Mounting Bolts

M5 x 0.8
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Do not over-tighten as this may crack or damage the housing. Correct torque provides a stable mount and good ground.

Wiring Harness

1

Wiring Harness Connector Mounting Bolts

Varies, typically M4 or smaller
Torque Specification
2 ft-lbs (3 N·m)
Important Notes
Use caution and avoid over-tightening. These fasteners are often plastic and easily damaged. Hand-tightening plus a small additional turn is generally sufficient. If a specific torque spec is available for the fastener use it.

Emissions Sensors

Torque specifications for Emissions_sensors

Exhaust System

1

EGR Valve Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure a proper seal between the EGR valve and the intake/exhaust manifold. Overtightening can damage the valve or threads.
2

Exhaust Manifold/Headers to Cylinder Head Bolts

M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Tighten in a criss-cross pattern to ensure even pressure distribution and prevent leaks. A multi-step torque process might be required depending on manifold type. Check for manufacturer specific patterns.
3

Exhaust Pipe to Exhaust Manifold/Headers Bolts

M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure a proper seal to prevent exhaust leaks, which can affect sensor readings.
4

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Proper torque is essential for maintaining exhaust integrity and preventing false sensor readings. Use new gaskets when installing.
5

Muffler to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the connection is secure to prevent leaks which can impact sensor performance. Use new gaskets when installing.
6

Oxygen (O2) Sensor

M18 x 1.5
Torque Specification
31 ft-lbs (42 N·m)
Important Notes
This is a critical torque. Too little can cause leaks and too much can damage the sensor. Use anti-seize on the threads of the O2 sensor.
7

Nitrogen Oxide (NOx) Sensor Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the sensor is correctly mounted for accurate readings and a leak-free connection.
8

Exhaust Gas Temperature (EGT) Sensor Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Proper torque is critical for proper measurement and sealing. Use a new gasket if present.

Intake System

1

Mass Air Flow (MAF) Sensor Mounting Bolts

M5 x 0.8
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure proper sealing of the MAF sensor to prevent inaccurate readings. Do not over tighten the small bolts.
2

Intake Air Temperature (IAT) Sensor Mounting Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the sensor is securely mounted and properly sealed to prevent air leaks and provide accurate temperature readings.

Engine Management

1

Camshaft Position Sensor Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the sensor is mounted correctly and not over tightened.
2

Crankshaft Position Sensor Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
The sensor should be securely mounted to ensure an accurate reading. Do not over tighten the bolts.
3

Fuel Injector Rail Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure proper alignment of the fuel rail and even torque distribution to prevent fuel leaks. These bolts are often small, so be careful to not over tighten.

Exhaust

Torque specifications for Exhaust

Exhaust Manifold

1

Exhaust Manifold/Header to Cylinder Head Bolts

M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Use new bolts and crush washers for optimal sealing. Tighten in a criss-cross pattern. Ensure the gasket is correctly positioned before tightening.
2

Exhaust Manifold/Header to Cylinder Head Studs (if applicable)

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Apply a small amount of anti-seize compound to the stud threads to prevent seizing. Tighten in a criss-cross pattern. Ensure the gasket is correctly positioned before tightening.

Exhaust Piping

1

Exhaust Pipe to Exhaust Manifold/Header Bolts

M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Always use new gaskets. Tighten evenly and in a criss-cross pattern. Confirm proper alignment of the exhaust components before tightening.
2

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Use new gaskets. Tighten evenly in a criss-cross pattern. Ensure correct alignment of components before tightening to prevent leaks and stress.

Muffler

1

Muffler to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure that the exhaust system is properly supported before tightening the bolts. Use new gaskets for a proper seal. Tighten in a criss-cross pattern.

Support Components

1

Exhaust Hanger Bracket Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Do not overtighten to prevent damage to the rubber isolators. Ensure proper alignment of the hanger before tightening. This value is an estimate based on similar-sized bolts.

Sensors And Clamps

1

Oxygen Sensor Mounting Torque

M8 x 1.25 (varies based on sensor)
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Torque specifications can vary, check specific sensor manufacturer data if available. This value is an estimated value. Be very careful not to over tighten. Use anti-seize on the threads if necessary.
2

Exhaust Band Clamp Torque

N/A
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Torque specifications are for a standard sized clamp. Tighten evenly to prevent leaks, but do not over tighten. Ensure the clamp is properly positioned over the joint.

Fuel

Torque specifications for Fuel

Fuel Rail And Injectors

1

Fuel Rail Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten bolts in a criss-cross pattern to ensure even clamping pressure. Ensure all threads are clean and free of debris. Over-tightening may cause damage to the fuel rail and cause leaks.
2

Fuel Injector Mounting Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure that the injector O-rings are properly seated. Do not over-tighten these bolts to prevent damage to the injector body. Ensure all threads are clean and free of debris.
3

Fuel Pressure Regulator Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
These bolts often secure the fuel pressure regulator directly to the fuel rail. Ensure proper seating of the regulator before tightening. Ensure all threads are clean and free of debris.

Fuel Delivery And Filtration

1

Fuel Pump Mounting Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
These bolts secure the fuel pump assembly to the fuel tank. Do not over-tighten; excessive force could damage the fuel tank or the pump mounting flange. Some bolts may be torque-to-yield and require replacement after removal. Check the vehicle's service manual for specific guidance. Ensure all threads are clean and free of debris.
2

Fuel Filter Mounting Bolt/Nut

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
This bolt or nut secures the fuel filter housing to the vehicle's body or frame. Ensure the filter is properly seated before tightening. Ensure all threads are clean and free of debris.
3

Fuel Line Connection Fitting (General)

Varies by fitting
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Torque for fuel line fittings varies greatly depending on the type and material. A general value of 15 ft-lbs (20 N·m) is an estimate for common sizes. Always refer to the manufacturer's specifications for the specific fitting used. Inch pound specs may appear lower than foot-pound specs. This is an estimated value, use caution, and reference the specific manufacturer for actual specifications. Ensure all threads are clean and free of debris.

Fuel Tank And Filler

1

Fuel Filler Neck Mounting Bolts

M6 x 1.0
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
These bolts secure the fuel filler neck to the vehicle body. Ensure that the filler neck is properly aligned with the fuel tank. Ensure all threads are clean and free of debris.
2

Fuel Tank Sending Unit Lock Ring

N/A
Torque Specification
N/A
Important Notes
The fuel tank sending unit often uses a lock ring rather than bolts. Tighten the lock ring by hand until it is fully engaged and properly seated, but do not over-tighten. Reference the specific vehicle's service manual for lock ring orientation as needed. No torque value is required for a lock ring, hand-tight is typically sufficient. Ensure all threads are clean and free of debris.

Hvac

Torque specifications for Hvac

Ac Compressor

1

A/C Compressor Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper alignment of the compressor before tightening. Use a calibrated torque wrench. Over-tightening may damage compressor housing.

Ac Lines

1

A/C Line Fittings

Varies, typically M10 x 1.0 or M12 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
These fittings are often aluminum or brass. Avoid over-tightening, as it can cause damage or leaks. Use a flare nut wrench to prevent rounding of fittings. This is an estimated torque value, as exact size varies.

Ac Condenser

1

A/C Condenser Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure that the condenser is correctly seated in its mounts. Over-tightening may damage the condenser or mounting points. This is an estimated torque value based on bolt size.

Hvac Blower

1

HVAC Blower Motor Mounting Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
These are typically low-torque fasteners securing the plastic housing of the blower motor. Over-tightening can damage the housing or the motor itself. This is an estimated value based on common blower motor housing bolt sizes.

Evaporator Housing

1

Evaporator Core Housing Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
The evaporator core housing is typically made of plastic. Over-tightening may damage the housing and create leaks. This is an estimated value based on similar plastic housing fasteners.

Heater Housing

1

Heater Core Housing Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
The heater core housing is usually made of plastic, so avoid over-tightening, which can crack the plastic or strip the threads. This is an estimated value based on similar plastic housing fasteners.

Hvac Control Panel

1

HVAC Control Panel Mounting Bolts

M4 x 0.7
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
These are low torque bolts securing the control panel housing, usually made of plastic. Over-tightening can damage the panel or the dashboard. This is an estimated torque value based on typical dashboard mounting screws.

Suspension

Torque specifications for Suspension

Front Strut Assembly

1

Strut Upper Mounting Bolts

M10 x 1.5
Torque Specification
48 ft-lbs (65 N·m)
Important Notes
Secures the top of the strut to the chassis/strut tower. Ensure proper alignment before tightening.
2

Sway Bar Link Nut (Strut Side)

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Connects the sway bar link to the strut assembly.

Front Control Arms

1

Control Arm Mounting Bolts (Chassis Side)

M12 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Secures the control arm to the vehicle's chassis or subframe. Ensure proper alignment before tightening.
2

Control Arm Ball Joint Nut

M14 x 1.5
Torque Specification
63 ft-lbs (85 N·m)
Important Notes
Secures the ball joint to the control arm or steering knuckle.

Steering Components

1

Tie Rod End Nut

M12 x 1.5
Torque Specification
52 ft-lbs (70 N·m)
Important Notes
Attaches the tie rod end to the steering knuckle or steering arm. Ensure alignment is correct.
2

Steering Gear/Rack Mounting Bolts

M12 x 1.75
Torque Specification
96 ft-lbs (130 N·m)
Important Notes
Secures the steering rack to the chassis or subframe. Ensure rack is correctly positioned.

Sway Bar

1

Sway Bar Mounting Bracket Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Secures sway bar mounting brackets to the chassis. Tighten evenly.
2

Sway Bar Link Nut (Control Arm Side)

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Connects the sway bar link to the control arm.

Subframe

1

Subframe Mounting Bolts

M14 x 1.5
Torque Specification
1. 81 ft-lbs (110 N·m) 2. 90°
Important Notes
These bolts are torque-to-yield and MUST be replaced after removal. Use a torque angle gauge for accurate tightening.

Wheel Speed Sensor

1

Wheel Speed Sensor Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Secures the wheel speed sensor to the steering knuckle. Do not overtighten as these bolts are small and can break easily.

Troubleshooting Guide

Common issues, diagnostic steps, and prevention guidelines

Common Issues

Bolt stretching, stripped threads, uneven torque patterns

Loose Components

Symptoms:
  • Rattling or vibration noises
  • Visible movement in components
  • Uneven panel gaps
Solutions:
  • Clean threads and mounting surfaces
  • Replace damaged fasteners
  • Apply proper torque in sequence
  • Use thread locker if specified

Stripped Fasteners

Symptoms:
  • Unable to achieve proper torque
  • Fastener spins freely
  • Visible thread damage
Solutions:
  • Use thread repair kit if appropriate
  • Install thread insert (HeliCoil)
  • Replace component if threaded hole is damaged
  • Upgrade to higher grade fastener if recommended

Overtightened Components

Symptoms:
  • Cracked or deformed parts
  • Broken fasteners
  • Compressed gaskets or seals
Solutions:
  • Replace damaged components
  • Use new fasteners
  • Follow proper torque sequence
  • Verify correct torque specifications

Diagnostic Steps

Visual inspection, torque verification, thread assessment

1

Visual Inspection

Inspect the affected area for any visible signs of damage or wear

  • Check for cracks or deformation
  • Look for signs of excessive wear
  • Verify proper fastener installation
2

Torque Verification

Verify the torque applied to the fasteners

  • Check the torque wrench calibration
  • Verify the torque specification
  • Compare the applied torque to the specification
3

Thread Assessment

Assess the condition of the threads

  • Check for signs of thread damage
  • Verify the thread type and size
  • Check for proper thread engagement

Prevention Guidelines

Best practices, maintenance tips, tool care

Best Practices

  • Always follow the recommended torque specification
  • Use the correct type and size of fasteners
  • Verify the torque wrench calibration regularly

Maintenance Tips

  • Regularly inspect the affected area for signs of wear or damage
  • Replace damaged or worn-out components promptly
  • Keep the work area clean and organized

Tool Care

  • Regularly clean and maintain the torque wrench
  • Store the torque wrench in a dry and secure location
  • Verify the torque wrench calibration before each use

Frequently Asked Questions

Find answers to common questions about torque specifications

Q1

What are the recommended torque specifications for the cylinder head bolts on a 2012 BMW 750i?

The cylinder head bolts on a 2012 BMW 750i require a torque of 40 Nm (29.5 ft-lb) for the first stage and 90° ± 5° for the second stage.

Q2

What IS the proper torque for the oil pan drain plug on a 2015 BMW 750i?

The oil pan drain plug on a 2015 BMW 750i should be torqued to 30 Nm (22.1 ft-lb).

Q3

What type of torque wrench IS recommended for critical engine components like the cylinder head?

A dial or digital torque wrench with an accuracy of ±3% or better should be used for critical engine components. Ensure it IS properly calibrated.

Q4

Can I use a regular wrench to tighten bolts instead of a torque wrench?

No. Using a regular wrench can result in over-tightening or under-tightening bolts, potentially causing damage. Always use a calibrated torque wrench to achieve the specified torque.

Q5

What IS the significance of proper torque application?

Proper torque ensures that bolts are tightened sufficiently to maintain proper component operation, prevent leaks, and avoid damage caused by over- or under-tightening.

Q6

Where can I find additional torque specifications for my BMW 750i?

Refer to the official BMW repair manual for your specific vehicle year and model for comprehensive torque specifications.

Environmental Considerations

Temperature, humidity, and seasonal effects on torque specifications

Temperature Effects

Includes: High Heat, Cold Weather, Thermal Cycling

Temperature can significantly impact torque values and fastener behavior

Cold Weather

Effects:
  • Increased material brittleness
  • Higher torque required due to thread contraction
  • Reduced thread lubricant effectiveness
Recommendations:
  • Allow components to warm to room temperature when possible
  • Consider using winter-grade thread lubricants
  • Check torque values more frequently during winter months

Hot Weather

Effects:
  • Thermal expansion of components
  • Decreased friction in threads
  • Accelerated lubricant breakdown
Recommendations:
  • Check torque when components are at normal operating temperature
  • Use temperature-resistant thread lockers
  • Consider re-torquing after heat cycles

Humidity and Corrosion

Covers: Rust Prevention, Salt Exposure, Moisture Control

Moisture and corrosion can affect fastener integrity and torque values

High Humidity

Effects:
  • Accelerated corrosion formation
  • Reduced friction coefficient
  • Potential thread seizing
Prevention:
  • Use corrosion-resistant fasteners
  • Apply appropriate anti-seize compounds
  • Maintain proper protective coatings

Salt Exposure

Effects:
  • Rapid corrosion development
  • Thread damage
  • Seized fasteners
Prevention:
  • Regular underbody washing
  • Use of sacrificial anodes where appropriate
  • Application of protective coatings

Seasonal Maintenance

Spring, Summer, Fall, and Winter maintenance schedules

Spring

  • Inspect for winter damage
  • Clean and protect exposed fasteners
  • Check torque on critical components

Summer

  • Monitor heat-affected components
  • Check expansion-related loosening
  • Inspect cooling system mounts

Fall

  • Prepare for winter conditions
  • Apply corrosion protection
  • Verify all fasteners are properly torqued

Winter

  • More frequent inspection of critical fasteners
  • Check for salt damage
  • Monitor suspension component torque

Related Resources

Tools, service procedures, and technical bulletins

Recommended Tools

BMW Bolt Torque Specifications for 750i (2008-2015)

A comprehensive document with all torque values for the BMW 750i (2008-2015) from 30 Nm to 200 Nm.

  • Official BMW document
Learn more
Service Procedures
Technical Service Bulletins

Legal Disclaimer

Important information about using this content

Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.

General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability

The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.

We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.

Technical Information
  • All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
  • Vehicle specifications and procedures may vary by model year, trim level, and region.
  • Always follow the manufacturer's recommended procedures and safety precautions.
  • Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
  • If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.

About the Author

Expert automotive knowledge and experience

Alan Montanye - Automotive Technical Specialist
ASE

Alan Montanye

Automotive Technical Specialist

ASE Master Certified Technician with over a decade of hands-on experience in automotive repair and diagnostics.

Facebook Contact
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions

Diagnostic

Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.

Repair

Expert in both traditional mechanical repairs and modern vehicle systems.

Additional Expertise

Documentation

Created over 500 detailed repair guides and technical documents.

Training

Conducted technical training sessions and contributed to repair databases.

Certifications & Research

Certifications

  • ASE Master Technician Certification
  • Advanced Diagnostic Specialist
  • Hybrid/Electric Vehicle Systems
  • Performance Tuning Expert

Research & Community

Actively researches emerging technologies and contributes to automotive forums.

© 2025 BMW Specs. All rights reserved.

Privacy Policy Terms of Service