BMW Vehicle Models 750i 2001-2008 Torque Specifications
BMW Vehicle Models 750i 2001-2008

BMW Vehicle Models 750i 2001-2008 Torque Specifications

Complete BMW Vehicle Models 750i 2001-2008 torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.

Updated

Important Information

Safety guidelines and reference information for proper torque application

Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083

Common Torque Patterns

Star Pattern

Used for wheels and other circular bolt patterns

Star Pattern torque pattern diagram showing proper bolt tightening sequence
Cross Pattern

Used for gaskets and cover plates

Cross Pattern torque pattern diagram showing proper bolt tightening sequence
Sequential Pattern

Used for head bolts and other critical components

Sequential Pattern torque pattern diagram showing proper bolt tightening sequence

Common Mistakes to Avoid

Over-tightening

Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.

Prevention:

Always use a calibrated torque wrench and follow specifications exactly.

Incorrect Torque Sequence

Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.

Prevention:

Follow the manufacturer's specified torque sequence pattern.

Dirty Threads

Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.

Prevention:

Clean and inspect all threads before assembly. Use new thread locker if specified.

Reusing TTY Bolts

Torque-to-yield bolts are designed to stretch and must not be reused.

Prevention:

Always replace TTY bolts with new ones. They are single-use only.

Dry vs. Lubricated

Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.

Prevention:

Check if specs are for dry or lubricated threads. Use specified lubricant when required.

Recommended Tools

Torque Wrench (1/4" Drive)

Range: 2-25 ft-lbs
Small fasteners, delicate components

Torque Wrench (3/8" Drive)

Range: 10-100 ft-lbs
Most common automotive fasteners

Torque Wrench (1/2" Drive)

Range: 30-250 ft-lbs
Large fasteners, wheels

Angle Gauge

Torque-to-yield (TTY) bolts

Torque Wrench Care

  • Calibrate annually or after 5,000 clicks
  • Store at lowest setting
  • Keep clean and lubricated

Search Specifications

Search by component name, bolt size, or description

Torque Calculator

Convert between different torque units

4.8l Engine

Torque specifications for 4.8L Engine

Cylinder Head

1

Cylinder Head Bolts

M12 x 1.5
Torque Specification
1. 23 ft-lbs (31 N·m)
Important Notes
First stage torque. Additional angular torque steps may be required. Refer to the official repair manual for complete procedure.
2

Valve Cover Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten bolts evenly. Do not overtighten to avoid damaging the valve cover.
3

Rocker Arms/Shafts Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure rocker arms are properly positioned before tightening.
4

Camshaft Position Sensor Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure sensor is correctly positioned before tightening. These bolts are very small, and easy to damage.
5

VANOS Solenoid Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the solenoids are properly seated. These bolts are very small, and easy to damage.
6

Ignition Coil Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure the ignition coils are properly seated. These bolts are very small, and easy to damage.
7

Spark Plugs

M14 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure proper seating of the spark plug. Do not overtighten.
8

Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Tighten bolts evenly to prevent exhaust leaks. Use a proper tightening sequence.

Engine Block

1

Main Bearing Bolts

M12 x 1.5
Torque Specification
1. 58 ft-lbs (78 N·m)
Important Notes
First stage torque. Additional angular torque steps may be required. Refer to the official repair manual for complete procedure.
2

Connecting Rod Nuts

M10 x 1.25
Torque Specification
1. 22 ft-lbs (30 N·m)
Important Notes
First stage torque. Additional angular torque steps may be required. Refer to the official repair manual for complete procedure.
3

Oil Pan Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure oil pan is properly seated against the block. These bolts are very small, and easy to damage.
4

Oil Drain Plug Bolt

M14 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Use a new crush washer. Do not overtighten.
5

Oil Filter Housing Bolt

M16 x 1.5
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure proper seating and sealing of the filter housing. Do not overtighten.
6

Oil Filter Cap

N/A
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Tighten by hand until snug. Do not overtighten. Estimate based on similar components.
7

Knock Sensor Bolt

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the sensor is properly seated against the block.
8

Coolant Drain Plug on Engine Block

M12 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Use a new crush washer. Do not overtighten.
9

Rear Main Seal Housing Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure the housing is properly seated against the block. Use a proper tightening sequence.

Intake System

1

Intake Manifold Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure proper seating and alignment. Tighten in a crisscross pattern.
2

Throttle Body Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure the throttle body is properly aligned and seated.
3

EGR Valve Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure EGR valve is properly seated. These bolts are very small, and easy to damage.
4

Fuel Rail Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure proper sealing of fuel rail to the intake. These bolts are very small, and easy to damage.
5

Fuel Injector Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure injectors are correctly installed. These bolts are very small, and easy to damage.
6

Fuel Injector Rail Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure the fuel rail is correctly positioned. These bolts are very small, and easy to damage.

Cooling System

1

Water Pump Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure the water pump is properly seated with a new gasket. These bolts are very small, and easy to damage.
2

Water Pump Pulley Bolts

M8 x 1.25
Torque Specification
89 ft-lbs (120 N·m)
Important Notes
Ensure pulley is correctly seated on the water pump. This is a high torque application.
3

Thermostat Housing Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure proper seating of the housing with a new gasket. These bolts are very small, and easy to damage.
4

Coolant Temperature Sensor

N/A
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Ensure proper seating and sealing of the sensor. Do not overtighten. Estimate based on similar components.

Timing System

1

Timing Belt/Chain Tensioner Bolt

M10 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the tensioner is correctly positioned. This is a critical bolt.
2

Camshaft Sprocket Bolt

M10 x 1.25
Torque Specification
66 ft-lbs (90 N·m)
Important Notes
Ensure sprockets are properly aligned before tightening. This is a high torque application.
3

Upper Timing Cover Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure cover is seated correctly. These bolts are very small, and easy to damage.

Crankshaft Components

1

Flywheel Bolts

M12 x 1.5
Torque Specification
88 ft-lbs (120 N·m)
Important Notes
Use new bolts for installation. Tighten in a star pattern.
2

Crankshaft Pulley/Harmonic Balancer Bolt

M16 x 1.5
Torque Specification
184 ft-lbs (250 N·m)
Important Notes
Ensure the pulley is correctly seated. This is a high torque application.

6hp Transmission

Torque specifications for 6hp Transmission

Transmission Mounting

1

Transmission Mounting Bolts

M12 x 1.75
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
These bolts secure the transmission to the chassis or subframe. Ensure proper alignment before tightening.

Transmission Case

1

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure a new gasket is used and torque bolts in a criss-cross pattern to avoid leaks. This is estimated.
2

Transmission Drain and Fill Plugs

M22 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure a new sealing washer is used. Avoid over-tightening to prevent damage to the transmission case.

Mechatronics

1

Mechatronics Unit Mounting Bolts (Valve Body)

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten in a criss-cross pattern. This torque value is estimated. Ensure a new gasket is used.
2

Transmission Control Module (TCM) Mounting Bolts

M5 x 0.8
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensure proper alignment of the TCM when tightening. This torque value is estimated.
3

Transmission Solenoid Mounting Bolts

M4 x 0.7
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Be very careful not to over-tighten these small bolts. This torque value is estimated.

Fluid Lines

1

Transmission Fluid Cooler Line Fittings

M12 x 1.5
Torque Specification
19 ft-lbs (26 N·m)
Important Notes
Use new crush washers when installing. Do not over-torque. Value is estimated for banjo bolts.

Shaft Flanges

1

Transmission Input Shaft Flange Bolts

M12 x 1.75
Torque Specification
88 ft-lbs (120 N·m)
Important Notes
Ensure the flange is properly aligned before tightening.
2

Transmission Output Shaft Flange Bolts

M12 x 1.75
Torque Specification
88 ft-lbs (120 N·m)
Important Notes
Ensure the flange is properly aligned before tightening.

Torque Converter

1

Torque Converter to Flywheel Bolts

M10 x 1.5
Torque Specification
1. 44 ft-lbs (60 N·m) 2. 90°
Important Notes
These bolts are torque-to-yield. Follow the torque sequence precisely. Always use new bolts.

Driveshaft

1

Propeller/Drive Shaft Bolts

M12 x 1.75
Torque Specification
89 ft-lbs (120 N·m)
Important Notes
Ensure proper alignment of the driveshaft before tightening the bolts.

Body

Torque specifications for Body

Fuel System

1

Fuel Tank Strap Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure straps are positioned correctly before tightening. Use a crisscross pattern.
2

Fuel Filler Neck Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Be careful not to overtighten and potentially damage the filler neck or body panel.

Electrical System

1

Battery Terminal Nuts

M6 x 1.0
Torque Specification
4 ft-lbs (5 N·m)
Important Notes
Do not overtighten as this can damage the terminal or the battery.

Body Panels

1

Hood Hinge Bolts to Body

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
If aluminum, use 13 ft-lbs (18 N·m). Ensure proper hood alignment before final tightening.
2

Fender Bolts to Body

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten bolts in a sequence working from the center outwards.
3

Door Hinge Bolts to Body

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure door alignment is correct before final torque application.
4

Door Latch/Striker Bolts to Body

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Adjust striker position for proper door latching before tightening fully.
5

Bumper Mounting Bolts to Body

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use a star pattern when tightening if multiple bolts are present. Torque values may vary slightly based on mounting location.
6

Headlight Mounting Bolts to Body

M5 x 0.8
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Be careful not to over-tighten as the mounting points can easily be damaged.
7

Taillight Mounting Bolts to Body

M5 x 0.8
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Be careful not to over-tighten as the mounting points can easily be damaged.
8

Grille Mounting Bolts to Body

M5 x 0.8
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Be careful not to over-tighten as the mounting points are often plastic.

Trim Panels

1

Trim Panel Mounting Screws

N/A
Torque Specification
0.33 ft-lbs (0.5 N·m)
Important Notes
Use a hand driver and do not overtighten these screws, which could easily damage the plastic mounting points.

Brakes

Torque specifications for Brakes

Front Brake Caliper

1

Front Caliper Mounting Bolts

M12 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
These bolts secure the caliper to the caliper mounting bracket.
2

Front Brake Pad Retaining Pin/Bolt

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
These pins or small bolts secure the brake pads within the caliper. Ensure proper pad seating.
3

Front Brake Line Banjo Bolt

M10 x 1.0
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Secures the brake line to the caliper. Use new crush washers. Estimated value.

Front Caliper Bracket

1

Front Caliper Bracket Mounting Bolts

M14 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
These bolts attach the bracket to the steering knuckle. Ensure both surfaces are clean.

Front Brake Rotor

1

Front Brake Rotor Retaining Bolt/Set Screw

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Small screw that holds the rotor against the hub during assembly. Estimated Value.

Rear Brake Caliper

1

Rear Caliper Mounting Bolts

M12 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
These bolts secure the rear caliper to the caliper mounting bracket.
2

Rear Brake Pad Retaining Pin/Bolt

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
These pins or small bolts secure the brake pads within the caliper. Ensure proper pad seating.
3

Rear Brake Line Banjo Bolt

M10 x 1.0
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Secures the brake line to the caliper. Use new crush washers. Estimated Value.

Rear Caliper Bracket

1

Rear Caliper Bracket Mounting Bolts

M14 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
These bolts attach the bracket to the wheel hub carrier. Ensure both surfaces are clean.

Rear Brake Rotor

1

Rear Brake Rotor Retaining Bolt/Set Screw

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Small screw that holds the rotor against the hub during assembly. Estimated value.

Drivetrain

Torque specifications for Drivetrain

Engine Interface

1

Flywheel Bolts

M10 x 1.25
Torque Specification
88 ft-lbs (120 N·m)
Important Notes
Apply threadlocker to bolts. Ensure flywheel is properly seated before tightening.
2

Torque Converter Bolts

M10 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Estimated value. Ensure proper torque converter alignment before tightening. Use threadlocker.

Transmission Mounting

1

Transmission Mounting Bolts

M12 x 1.75
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure transmission is properly aligned before torquing.
2

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten evenly to avoid leaks. Use a new gasket or sealant.
3

Transmission Drain Plug

M18 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Use a new sealing washer or O-ring. Do not over-tighten.
4

Transmission Fill Plug

M18 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Use a new sealing washer or O-ring. Do not over-tighten.

Driveshaft Axle

1

Drive Axle/Half Shaft Bolts

M10 x 1.25
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Tighten bolts evenly in a cross pattern.
2

CV Joint/Axle Nut

M24 x 1.5
Torque Specification
214 ft-lbs (290 N·m)
Important Notes
Use a new nut if required. Check wheel bearing play after torquing.
3

Propeller/Drive Shaft Bolts

M12 x 1.25
Torque Specification
89 ft-lbs (120 N·m)
Important Notes
Apply threadlocker. Tighten bolts evenly in a cross pattern.
4

Output Shaft Flange Bolts

M10 x 1.25
Torque Specification
58 ft-lbs (78 N·m)
Important Notes
Estimated value. Check for proper flange alignment. Use threadlocker.

Differential

1

Differential Mounting Bolts

M14 x 2.0
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Estimated value. Tighten bolts evenly. Ensure proper alignment.
2

Differential Drain Plug

M20 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Use a new sealing washer or O-ring. Do not over-tighten.
3

Differential Fill Plug

M20 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Use a new sealing washer or O-ring. Do not over-tighten.

Transfer Case

1

Transfer Case Mounting Bolts

M12 x 1.75
Torque Specification
48 ft-lbs (65 N·m)
Important Notes
Estimated value. Ensure proper alignment before tightening.

Electrical

Torque specifications for Electrical

Ignition System

1

Ignition Coil Mounting Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure coils are seated properly before tightening. Over-tightening can damage the coil or mounting surface.

Starting System

1

Starter Motor Mounting Bolt

M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the starter motor is flush against the engine block before tightening. Over-tightening can damage the starter housing or the engine block.

Charging System

1

Alternator Mounting Bolt

M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the alternator is flush against the engine mount before tightening. Over-tightening can damage the alternator housing or mount.

Battery System

1

Battery Terminal Nut

M6 x 1.0
Torque Specification
4 ft-lbs (5 N·m)
Important Notes
Ensure terminals are clean and free of corrosion before tightening. Do not over-tighten as it can damage the battery terminal.

Engine Control Unit

1

ECU Mounting Bolt

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Ensure the ECU is flush with mounting surface before tightening. Over-tightening can damage the ECU or its mounting points. Estimated Value.

Ground Connections

1

Ground Strap/Cable Bolt (Engine, Chassis, Body)

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure ground straps are clean and make good contact with the mounting surface before tightening. Over-tightening can damage the strap or mounting point.

Fuse And Relay Boxes

1

Fuse Box/Relay Box Mounting Bolt

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Ensure the box is flush with mounting surface before tightening. Over-tightening can damage the box or its mounting points. Estimated Value.

Sensor Mounting

1

Crankshaft/Camshaft Position Sensor Mounting Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure sensor is seated properly before tightening. Over-tightening can damage the sensor or mounting surface.
2

Oxygen Sensor Mounting Bolt

M8 x 1.25
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure sensor is seated properly before tightening. Over-tightening can damage the sensor or mounting surface. Estimated Value.

Lighting System

1

Headlight Mounting Bolt

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Ensure the headlight housing is flush with the body panel before tightening. Over-tightening can damage the headlight housing or mounting points. Estimated Value.
2

Tail Light Mounting Bolt

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Ensure the tail light housing is flush with the body panel before tightening. Over-tightening can damage the tail light housing or mounting points. Estimated Value.

Wiper System

1

Wiper Motor Mounting Bolt

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the wiper motor is mounted flush and aligned correctly before tightening. Over-tightening can damage the motor housing or mounting points.

Abs System

1

ABS Module Mounting Bolt

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Ensure the ABS module is mounted flush and aligned correctly before tightening. Over-tightening can damage the module. Estimated Value.

Emissions Sensors

Torque specifications for Emissions_sensors

Exhaust System

1

Exhaust Manifold to Cylinder Head Bolts

M8 x 1.25
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Ensure even tightening to prevent warping. Use new gaskets.
2

Exhaust Pipe to Exhaust Manifold/Headers Bolts

M10 x 1.5
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Use new gaskets. Ensure proper alignment before tightening.
3

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Use new gaskets and ensure a proper seal to prevent leaks.
4

Oxygen (O2) Sensor

M18 x 1.5
Torque Specification
32 ft-lbs (43 N·m)
Important Notes
Torque value is an estimate for typical M18x1.5 O2 sensors. Verify with the sensor manufacturer's specifications.

Intake System

1

Intake Manifold Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten bolts in a crisscross pattern to ensure even sealing. Use new gaskets.
2

Throttle Body Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure proper sealing to prevent vacuum leaks. Use new gaskets.
3

Mass Air Flow (MAF) Sensor Mounting Bolts

M5 x 0.8
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Do not overtighten as the sensor housing can be fragile. Estimated value, verify with service manual.
4

Manifold Absolute Pressure (MAP) Sensor Mounting Bolts or Screws

M5 x 0.8
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure a proper seal to prevent vacuum leaks. Estimated value, verify with service manual.

Fuel System

1

Fuel Injector Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Use new O-rings on injectors. Do not overtighten.
2

Fuel Injector Rail Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure proper alignment and seating. Do not overtighten.

Egr And Air Injection

1

EGR Valve Bolts

M8 x 1.25
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Use new gaskets and ensure a leak-free seal.
2

Secondary Air Injection Pump Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated torque value, verify with BMW specific service manual. Do not overtighten.

Exhaust

Torque specifications for Exhaust

Exhaust Manifold

1

Exhaust Manifold/Header to Cylinder Head Bolt

M8 x 1.25
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Tighten in a criss-cross pattern. Ensure proper gasket is used. Bolt size may vary - check before installation.
2

Exhaust Manifold/Header to Cylinder Head Bolt

M10 x 1.5
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Tighten in a criss-cross pattern. Ensure proper gasket is used. Bolt size may vary - check before installation.

Exhaust Piping

1

Exhaust Pipe to Exhaust Manifold/Header Bolt

M8 x 1.25
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Tighten evenly to ensure a proper seal. Check for exhaust leaks after installation. Bolt size may vary - check before installation.
2

Exhaust Pipe to Exhaust Manifold/Header Bolt

M10 x 1.5
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Tighten evenly to ensure a proper seal. Check for exhaust leaks after installation. Bolt size may vary - check before installation.
3

Catalytic Converter to Exhaust Pipe Bolt

M8 x 1.25
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Tighten evenly to ensure a proper seal. Check for exhaust leaks after installation. Bolt size may vary - check before installation.
4

Catalytic Converter to Exhaust Pipe Bolt

M10 x 1.5
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Tighten evenly to ensure a proper seal. Check for exhaust leaks after installation. Bolt size may vary - check before installation.
5

Muffler to Exhaust Pipe Bolt

M8 x 1.25
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Tighten evenly to ensure a proper seal. Check for exhaust leaks after installation. Bolt size may vary - check before installation.
6

Muffler to Exhaust Pipe Bolt

M10 x 1.5
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Tighten evenly to ensure a proper seal. Check for exhaust leaks after installation. Bolt size may vary - check before installation.

Exhaust Sensors

1

O2 Sensor Mounting Bolt

M10 x 1.5
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure proper sensor seating and sealing. Use anti-seize on sensor threads (if applicable). Bolt size may vary - check before installation.
2

O2 Sensor Mounting Bolt

M12 x 1.75
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure proper sensor seating and sealing. Use anti-seize on sensor threads (if applicable). Bolt size may vary - check before installation.

Exhaust Mounts

1

Exhaust Hanger Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Do not overtighten, which may cause damage to the rubber isolators. Check the condition of rubber isolators. Bolt size may vary - check before installation.
2

Exhaust Hanger Bolt

M10 x 1.5
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Do not overtighten, which may cause damage to the rubber isolators. Check the condition of rubber isolators. Bolt size may vary - check before installation.
3

Exhaust Clamp Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Tighten evenly to ensure a proper seal, usually in an alternating pattern. Check for exhaust leaks after installation. Bolt size may vary - check before installation.

Fuel

Torque specifications for Fuel

Fuel Rail

1

Fuel Rail Mounting Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Applies to bolts securing the fuel rail to the intake manifold or cylinder head. Ensure threads are clean and lightly lubricated with engine oil. This is a general specification and may be lower or higher depending on the specific component.
2

Fuel Injector Mounting Bolts/Screws

M5 x 0.8
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Secures each fuel injector to the fuel rail or intake manifold. Over-tightening can damage the injector or cause leaks. Use a criss-cross pattern.
3

Fuel Pressure Regulator Mounting Bolts/Screws

M5 x 0.8
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Secures the fuel pressure regulator to the fuel rail. Consult the specific component's service manual for exact torque if available. This is a general estimation and may differ based on the component.

Fuel Pump

1

Fuel Pump Mounting Bolts

M8 x 1.25
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Secures the fuel pump assembly to the fuel tank or mounting bracket. Ensure the fuel pump is properly seated against its mounting surface prior to tightening.
2

Fuel Filler Neck Bolts/Screws

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Secures the fuel filler neck to the vehicle body or fuel tank. Over-tightening can damage the filler neck or its mounting flange. Confirm proper alignment of components before tightening.
3

Fuel Tank Sending Unit Retaining Bolts

M6 x 1.0
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Secures the fuel tank sending unit. Apply torque evenly to avoid leaks. This is an estimated value and should be verified against the vehicle's service manual. Note, this may be a lock ring instead.
4

Fuel Tank Vent/Purge Valve Mounting Bolts

M5 x 0.8
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Secures the fuel tank vent/purge valve. Verify correct seating of the valve on its mounting surface prior to tightening. This is a general estimation, and may differ based on the valve itself.

Fuel Lines

1

Fuel Line Banjo Bolts

M12 x 1.5
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Tighten banjo bolts to the specified torque. Always use new sealing washers and confirm the banjo bolt is properly aligned with the fuel line and component to which it is being tightened. Refer to the component's specification if available. Torque value may vary with banjo bolt size and material.
2

Fuel Filter Mounting Bolts/Nuts

M8 x 1.25
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
These bolts or nuts secure the fuel filter assembly to its mounting location, usually a bracket on the chassis. Make sure filter is seated properly and that any mounting surfaces are clean and corrosion free.

Hvac

Torque specifications for Hvac

Ac Compressor

1

A/C Compressor Mounting Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure bolts are tightened evenly to prevent compressor misalignment. Always use a calibrated torque wrench.
2

A/C Line Fittings

N/A (Fitting - Hand Tight)
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
These are typically flare or O-ring type fittings. Over-tightening can damage the fittings or O-rings. Tighten with proper tools. Estimated value.

Hvac Core Components

1

Evaporator Core Housing Bolts

M5 x 0.8
Torque Specification
6.5 ft-lbs (9 N·m)
Important Notes
Estimated value. Use care when tightening into plastic housings. Do not over-tighten.
2

Expansion Valve Mounting Bolts

M5 x 0.8
Torque Specification
6.5 ft-lbs (9 N·m)
Important Notes
Estimated value. Use care when tightening into plastic housings. Do not over-tighten.
3

Heater Core Inlet/Outlet Pipe Retaining Bolts/Clamp Bolts

M5 x 0.8 (or clamp)
Torque Specification
6.5 ft-lbs (9 N·m)
Important Notes
Estimated value. Do not over-tighten as damage can occur to the plastic housing or hose connections.

Hvac Blower And Control

1

HVAC Blower Motor Mounting Bolts

M5 x 0.8
Torque Specification
6.5 ft-lbs (9 N·m)
Important Notes
Estimated value. Do not over-tighten, as it may crack the plastic housing of the blower motor.
2

HVAC Control Module Mounting Bolts

M4 x 0.7
Torque Specification
6.5 ft-lbs (9 N·m)
Important Notes
Estimated value. Do not over-tighten, as it may crack the plastic housing or damage the circuit board.
3

Blend Door Actuator Mounting Bolts

M4 x 0.7
Torque Specification
6.5 ft-lbs (9 N·m)
Important Notes
Estimated value. Do not over-tighten as this may crack the plastic housing. Multiple actuators may exist.

Ac Condenser And Drier

1

Condenser Mounting Bolts/Screws

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure proper alignment before tightening. Always use a calibrated torque wrench.
2

Receiver Drier Mounting Bolts/Screws

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure proper alignment before tightening. Always use a calibrated torque wrench.

Dashboard Related

1

Dashboard Mounting Bolts Near HVAC Housing

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
These bolts are often accessed during HVAC repairs. Ensure proper tightening.

Suspension

Torque specifications for Suspension

Front Suspension

1

Strut/Shock Absorber Mounting Bolts

M12 x 1.75
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Secures the strut to the steering knuckle and/or chassis. Ensure proper alignment before tightening. These are typical high tensile strength bolts.
2

Front Upper Strut Mount Bolts (Strut to Mount)

M10 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
These bolts secure the strut to the upper mount. Ensure that the strut is correctly positioned in the mount before tightening.
3

Front Upper Strut Mount Bolts (Mount to Body)

M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Secures the upper strut mount to the vehicle body. Do not over tighten these bolts as this may damage the mount.
4

Control Arm Mounting Bolts

M14 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Bolts connect the control arm to the vehicle's frame or subframe. It's essential to torque these with the suspension at ride height to ensure proper bushing preload.
5

Ball Joint Nut

M12 x 1.75
Torque Specification
66 ft-lbs (90 N·m)
Important Notes
Secures the ball joint stud to the steering knuckle or control arm. Ensure the cotter pin is installed if equipped. Note that some applications use a torque to angle procedure.
6

Tie Rod End Nut

M12 x 1.75
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Secures the tie rod end to the steering knuckle. Ensure the cotter pin is installed if equipped.
7

Sway Bar Link Nut

M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Connects the sway bar link to the sway bar and strut or control arm. Do not overtighten.
8

Stabilizer Bar Mounting Bracket Bolts/Clamps

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
These bolts secure the sway bar mounting brackets to the chassis. Ensure the sway bar bushings are correctly positioned and not pinched.

Steering System

1

Steering Gear/Rack Bolts

M12 x 1.75
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Mounting bolts for securing the steering rack to the subframe or chassis. These are typically high tensile strength bolts.

Rear Suspension

1

Rear Upper Shock Mount Bolts (Shock to Mount)

M10 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
These bolts secure the shock to the upper mount. Ensure that the shock is correctly positioned in the mount before tightening.
2

Rear Upper Shock Mount Bolts (Mount to Body)

M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Secures the upper shock mount to the vehicle body. Do not over tighten these bolts as this may damage the mount.
3

Rear Lower Control Arm Mounting Bolts

M12 x 1.75
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
These bolts attach the lower control arm to the subframe or body. Ensure that the vehicle is at ride height before tightening.
4

Rear Upper Control Arm Mounting Bolts

M12 x 1.75
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
These bolts attach the upper control arm to the subframe or body. Ensure that the vehicle is at ride height before tightening.
5

Axle Carrier (Trailing Arm) Mounting Bolts

M14 x 1.5
Torque Specification
1. 88 ft-lbs (120 N·m) 2. 90°
Important Notes
Secures the trailing arm to the chassis/subframe. These are typically torque to yield bolts and must be replaced when removed. Torque to specification, then further tighten by the specified angle.

Subframe

1

Subframe Mounting Bolts

M14 x 2.0
Torque Specification
1. 88 ft-lbs (120 N·m) 2. 90°
Important Notes
These are typically torque to yield bolts and must be replaced when removed. Torque to specification, then further tighten by the specified angle.

Sensors

1

Ride Height Sensor Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Secures the ride height sensor to the suspension components. Do not overtighten as this could damage the sensor.
2

Wheel Speed Sensor Mounting Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Mounting bolts for securing the wheel speed sensor to the hub or knuckle. Do not over tighten as this could damage the sensor.

Troubleshooting Guide

Common issues, diagnostic steps, and prevention guidelines

Common Issues

Bolt stretching, stripped threads, uneven torque patterns

Loose Components

Symptoms:
  • Rattling or vibration noises
  • Visible movement in components
  • Uneven panel gaps
Solutions:
  • Clean threads and mounting surfaces
  • Replace damaged fasteners
  • Apply proper torque in sequence
  • Use thread locker if specified

Stripped Fasteners

Symptoms:
  • Unable to achieve proper torque
  • Fastener spins freely
  • Visible thread damage
Solutions:
  • Use thread repair kit if appropriate
  • Install thread insert (HeliCoil)
  • Replace component if threaded hole is damaged
  • Upgrade to higher grade fastener if recommended

Overtightened Components

Symptoms:
  • Cracked or deformed parts
  • Broken fasteners
  • Compressed gaskets or seals
Solutions:
  • Replace damaged components
  • Use new fasteners
  • Follow proper torque sequence
  • Verify correct torque specifications

Diagnostic Steps

Visual inspection, torque verification, thread assessment

1

Visual Inspection

Inspect the affected area for any visible signs of damage or wear

  • Check for cracks or deformation
  • Look for signs of excessive wear
  • Verify proper fastener installation
2

Torque Verification

Verify the torque applied to the fasteners

  • Check the torque wrench calibration
  • Verify the torque specification
  • Compare the applied torque to the specification
3

Thread Assessment

Assess the condition of the threads

  • Check for signs of thread damage
  • Verify the thread type and size
  • Check for proper thread engagement

Prevention Guidelines

Best practices, maintenance tips, tool care

Best Practices

  • Always follow the recommended torque specification
  • Use the correct type and size of fasteners
  • Verify the torque wrench calibration regularly

Maintenance Tips

  • Regularly inspect the affected area for signs of wear or damage
  • Replace damaged or worn-out components promptly
  • Keep the work area clean and organized

Tool Care

  • Regularly clean and maintain the torque wrench
  • Store the torque wrench in a dry and secure location
  • Verify the torque wrench calibration before each use

Frequently Asked Questions

Find answers to common questions about torque specifications

Q1

What IS the torque specification for the cylinder head bolts on a 2001-2008 BMW 750i?

40 lb-ft (54 Nm) in three stages: 20 lb-ft (27 Nm), 30 lb-ft (41 Nm), then 40 lb-ft (54 Nm) using an angle torque wrench.

Q2

What IS the recommended torque for the crankshaft pulley bolt?

280 lb-ft (380 Nm) with the engine at TDC, using a new bolt.

Q3

Can I use a regular torque wrench for engine component bolts?

No, an angle torque wrench IS required to ensure accurate torque application and prevent over-tightening.

Q4

What IS the torque specification for the spark plugs?

18 lb-ft (24 Nm) for the 2001-2003 models and 22 lb-ft (30 Nm) for the 2004-2008 models.

Q5

How do I torque the lug nuts on the wheels?

Tighten the lug nuts to 89 lb-ft (120 Nm) in a star pattern using a torque wrench. Double-check the torque after 50 miles.

Environmental Considerations

Temperature, humidity, and seasonal effects on torque specifications

Temperature Effects

Includes: High Heat, Cold Weather, Thermal Cycling

Temperature can significantly impact torque values and fastener behavior

Cold Weather

Effects:
  • Increased material brittleness
  • Higher torque required due to thread contraction
  • Reduced thread lubricant effectiveness
Recommendations:
  • Allow components to warm to room temperature when possible
  • Consider using winter-grade thread lubricants
  • Check torque values more frequently during winter months

Hot Weather

Effects:
  • Thermal expansion of components
  • Decreased friction in threads
  • Accelerated lubricant breakdown
Recommendations:
  • Check torque when components are at normal operating temperature
  • Use temperature-resistant thread lockers
  • Consider re-torquing after heat cycles

Humidity and Corrosion

Covers: Rust Prevention, Salt Exposure, Moisture Control

Moisture and corrosion can affect fastener integrity and torque values

High Humidity

Effects:
  • Accelerated corrosion formation
  • Reduced friction coefficient
  • Potential thread seizing
Prevention:
  • Use corrosion-resistant fasteners
  • Apply appropriate anti-seize compounds
  • Maintain proper protective coatings

Salt Exposure

Effects:
  • Rapid corrosion development
  • Thread damage
  • Seized fasteners
Prevention:
  • Regular underbody washing
  • Use of sacrificial anodes where appropriate
  • Application of protective coatings

Seasonal Maintenance

Spring, Summer, Fall, and Winter maintenance schedules

Spring

  • Inspect for winter damage
  • Clean and protect exposed fasteners
  • Check torque on critical components

Summer

  • Monitor heat-affected components
  • Check expansion-related loosening
  • Inspect cooling system mounts

Fall

  • Prepare for winter conditions
  • Apply corrosion protection
  • Verify all fasteners are properly torqued

Winter

  • More frequent inspection of critical fasteners
  • Check for salt damage
  • Monitor suspension component torque

Related Resources

Tools, service procedures, and technical bulletins

Recommended Tools

Digital Torque Wrench (10-100 Nm)

Essential for tightening fasteners to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the 750i.

  • Digital display for accurate readings
  • Audible alarm when target torque IS reached
  • Multiple units (Nm, ft-lb, in-lb)
  • Reversible ratcheting mechanism
Learn more
Service Procedures

Cylinder Head Bolt Torque Procedure

Technical procedure for tightening cylinder head bolts to specified torque values for the BMW 750i.

  • Clean all bolt threads and threads in cylinder head.
  • Use new bolts and apply BMW M10 engine oil to threads.
  • Tighten bolts in the correct sequence to 30 Nm (22 ft-lb).
  • Wait 120 seconds.
  • Tighten bolts in the same sequence to 60 Nm (44 ft-lb).
  • Wait 120 seconds.
  • Tighten bolts in the same sequence to 80 Nm (59 ft-lb).
  • Wait 120 seconds.
  • Tighten bolts in the same sequence to 90 Nm (66 ft-lb).
  • Wait 120 seconds.
  • Tighten bolts in the same sequence to 90 degrees.
  • Wait 120 seconds.
  • Tighten bolts in the same sequence to 90 degrees.
View full procedure

Connecting Rod Bolt Torque Procedure

Technical procedure for tightening connecting rod bolts to specified torque values for the BMW 750i.

  • Clean all bolt threads and threads in connecting rod.
  • Use new bolts.
  • Apply BMW Assembly Paste to threads.
  • Tighten bolts to 40 Nm (30 ft-lb).
  • Wait 120 seconds.
  • Tighten bolts to 60 Nm (44 ft-lb).
  • Wait 120 seconds.
  • Tighten bolts to 80 Nm (59 ft-lb).
  • Wait 120 seconds.
  • Tighten bolts to 90 degrees.
  • Wait 120 seconds.
  • Tighten bolts to 90 degrees.
View full procedure

Main Bearing Cap Bolt Torque Procedure

Technical procedure for tightening main bearing cap bolts to specified torque values for the BMW 750i.

  • Clean all bolt threads and threads in main bearing cap.
  • Use new bolts.
  • Apply BMW Assembly Paste to threads.
  • Tighten bolts to 30 Nm (22 ft-lb).
  • Wait 120 seconds.
  • Tighten bolts to 60 Nm (44 ft-lb).
  • Wait 120 seconds.
  • Tighten bolts to 90 degrees.
  • Wait 120 seconds.
  • Tighten bolts to 90 degrees.
View full procedure
Technical Service Bulletins

Cylinder Head Bolt Torque Specification Update

2004-03-01

Revised torque specifications for cylinder head bolts issued by BMW due to reported failures.

2001-2004 750i

Resolution: Replace cylinder head bolts with new bolts.Tighten bolts to updated torque specifications (see service procedure above).Replace cylinder head gasket.

Connecting Rod Bearing Clearance Specification Update

2006-07-15

Revised connecting rod bearing clearance specifications issued by BMW due to premature bearing wear.

2005-2008 750i

Resolution: Inspect connecting rod bearings for excessive wear.Replace bearings as necessary.Adjust bearing clearance to updated specification.

Legal Disclaimer

Important information about using this content

Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.

General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability

The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.

We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.

Technical Information
  • All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
  • Vehicle specifications and procedures may vary by model year, trim level, and region.
  • Always follow the manufacturer's recommended procedures and safety precautions.
  • Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
  • If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.

About the Author

Expert automotive knowledge and experience

Alan Montanye - Automotive Technical Specialist
ASE

Alan Montanye

Automotive Technical Specialist

ASE Master Certified Technician with over a decade of hands-on experience in automotive repair and diagnostics.

Facebook Contact
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions

Diagnostic

Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.

Repair

Expert in both traditional mechanical repairs and modern vehicle systems.

Additional Expertise

Documentation

Created over 500 detailed repair guides and technical documents.

Training

Conducted technical training sessions and contributed to repair databases.

Certifications & Research

Certifications

  • ASE Master Technician Certification
  • Advanced Diagnostic Specialist
  • Hybrid/Electric Vehicle Systems
  • Performance Tuning Expert

Research & Community

Actively researches emerging technologies and contributes to automotive forums.

© 2025 BMW Specs. All rights reserved.

Privacy Policy Terms of Service