BMW Vehicle Models 530i 2017-present Torque Specifications
BMW Vehicle Models 530i 2017-present

BMW Vehicle Models 530i 2017-present Torque Specifications

Complete BMW Vehicle Models 530i 2017-present torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.

Updated

Important Information

Safety guidelines and reference information for proper torque application

Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083

Common Torque Patterns

Star Pattern

Used for wheels and other circular bolt patterns

Star Pattern torque pattern diagram showing proper bolt tightening sequence
Cross Pattern

Used for gaskets and cover plates

Cross Pattern torque pattern diagram showing proper bolt tightening sequence
Sequential Pattern

Used for head bolts and other critical components

Sequential Pattern torque pattern diagram showing proper bolt tightening sequence

Common Mistakes to Avoid

Over-tightening

Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.

Prevention:

Always use a calibrated torque wrench and follow specifications exactly.

Incorrect Torque Sequence

Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.

Prevention:

Follow the manufacturer's specified torque sequence pattern.

Dirty Threads

Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.

Prevention:

Clean and inspect all threads before assembly. Use new thread locker if specified.

Reusing TTY Bolts

Torque-to-yield bolts are designed to stretch and must not be reused.

Prevention:

Always replace TTY bolts with new ones. They are single-use only.

Dry vs. Lubricated

Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.

Prevention:

Check if specs are for dry or lubricated threads. Use specified lubricant when required.

Recommended Tools

Torque Wrench (1/4" Drive)

Range: 2-25 ft-lbs
Small fasteners, delicate components

Torque Wrench (3/8" Drive)

Range: 10-100 ft-lbs
Most common automotive fasteners

Torque Wrench (1/2" Drive)

Range: 30-250 ft-lbs
Large fasteners, wheels

Angle Gauge

Torque-to-yield (TTY) bolts

Torque Wrench Care

  • Calibrate annually or after 5,000 clicks
  • Store at lowest setting
  • Keep clean and lubricated

Search Specifications

Search by component name, bolt size, or description

Torque Calculator

Convert between different torque units

2.0l Engine

Torque specifications for 2.0L Engine

Cylinder Head

1

Cylinder Head Bolts

M12 x 1.5
Torque Specification
1. 22 ft-lbs (30 N·m) 2. 90° 3. 90°
Important Notes
Use a three-step torque sequence, first to 22ft-lbs (30nm) then followed by 90 degree angle twice. Always replace cylinder head bolts. Follow specific tightening sequence as detailed in service manual.
2

Valve Cover Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Tighten in a criss-cross pattern. Overtightening can crack the valve cover. Use a new gasket.

Crankshaft

1

Main Bearing Bolts

M10 x 1.5
Torque Specification
1. 22 ft-lbs (30 N·m) 2. 70°
Important Notes
These bolts require a two-step torque sequence. Ensure proper lubrication and follow specified torque sequence.
2

Connecting Rod Nuts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure proper bearing alignment. Tighten in sequence.
3

Flywheel Bolts

M12 x 1.5
Torque Specification
78 ft-lbs (106 N·m)
Important Notes
Use new bolts and a thread locking compound.
4

Crankshaft Pulley/Harmonic Balancer Bolt

M18 x 1.5
Torque Specification
1. 74 ft-lbs (100 N·m) 2. 90°
Important Notes
Use a new bolt and always use an angle meter to achieve final torque. This is a one-time use bolt and must be replaced.

Oil System

1

Oil Pan Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Tighten in a criss-cross pattern. Use a new gasket or sealant as specified.
2

Oil Filter Cap

N/A
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Use new o-ring.
3

Oil Filter Housing Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Tighten evenly. Use a new gasket.
4

Oil Drain Plug

M14 x 1.5
Torque Specification
27 ft-lbs (37 N·m)
Important Notes
Use new crush washer.

Timing System

1

Timing Belt/Chain Tensioner Bolt

M8 x 1.25
Torque Specification
27 ft-lbs (37 N·m)
Important Notes
Ensure proper tensioner function after torquing.
2

Camshaft Sprocket Bolt

M10 x 1.5
Torque Specification
42 ft-lbs (57 N·m)
Important Notes
Ensure proper alignment before tightening. Use new bolts.

Intake Exhaust

1

Throttle Body Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Use new gasket.
2

Intake Manifold Bolts

M8 x 1.25
Torque Specification
14 ft-lbs (19 N·m)
Important Notes
Tighten in a criss-cross pattern to prevent vacuum leaks.
3

Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
27 ft-lbs (37 N·m)
Important Notes
Tighten in a sequence starting from center outwards.
4

EGR Valve Bolts

M6 x 1.0
Torque Specification
14 ft-lbs (19 N·m)
Important Notes
Use new gasket.

Fuel System

1

Fuel Rail Bolts

M6 x 1.0
Torque Specification
14 ft-lbs (19 N·m)
Important Notes
Ensure proper alignment to prevent fuel leaks.
2

Fuel Injector Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Tighten evenly to avoid leaks.

Ignition System

1

Spark Plugs

N/A
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Do not overtighten to avoid damaging cylinder head threads.
2

Ignition Coil Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Do not overtighten to avoid damaging the coils.

Valve Train

1

Rocker Arms/Shafts Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure proper rocker arm/shaft alignment before torquing.

Cooling System

1

Water Pump Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Tighten evenly to ensure proper sealing.
2

Water Pump Pulley Bolts

M6 x 1.0
Torque Specification
14 ft-lbs (19 N·m)
Important Notes
Tighten evenly.
3

Thermostat Housing Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Use new gasket. Tighten in a criss-cross pattern.

Accessory Drive

1

Serpentine/Accessory Drive Belt Tensioner Bolt

M10 x 1.5
Torque Specification
27 ft-lbs (37 N·m)
Important Notes
Ensure proper tensioner function after torquing.
2

Drive Belt Idler Pulley Bolt

M10 x 1.5
Torque Specification
27 ft-lbs (37 N·m)
Important Notes
Ensure proper idler pulley alignment.

Sensors

1

Camshaft Position Sensor Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Do not overtighten to avoid damaging sensor.
2

Crankshaft Position Sensor Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Do not overtighten to avoid damaging sensor.
3

Knock Sensor Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Do not overtighten to avoid damaging sensor.
4

Coolant Temperature Sensor

N/A
Torque Specification
14 ft-lbs (19 N·m)
Important Notes
Ensure proper seating to prevent leaks. Sensor is likely brass or similar requiring specific torque.
5

Valve Timing Solenoid (VANOS) Bolt

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Do not overtighten to avoid damaging solenoid and threads.

3.0l Engine

Torque specifications for 3.0L Engine

Cylinder Head

1

Cylinder Head Bolts

M12 x 1.75
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Torque in specified sequence. These bolts may be torque-to-yield; always replace with new bolts when disassembling.
2

Valve Cover Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Tighten in a criss-cross pattern to ensure even pressure on the gasket.
3

Rocker Arm/Shaft Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure proper rocker arm alignment before tightening. Torque evenly to prevent binding or damage.
4

Camshaft Position Sensor Bolt

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Do not overtighten; sensor housing is often fragile.

Engine Block

1

Main Bearing Bolts

M12 x 1.75
Torque Specification
1. 30 ft-lbs (41 N·m) 2. 60 ft-lbs (81 N·m)
Important Notes
Torque in specified sequence, may require an additional angle torque, refer to the service manual. Lubricate bolt threads with engine oil.
2

Oil Pan Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Tighten in a criss-cross pattern to evenly compress the gasket.
3

Crankshaft Position Sensor Bolt

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure sensor is properly seated before tightening, avoid over-tightening.
4

Water Pump Bolts

M8 x 1.25
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Tighten evenly to avoid warping the water pump housing.
5

Oil Drain Plug Bolt

M14 x 1.5
Torque Specification
27 ft-lbs (37 N·m)
Important Notes
Use a new sealing washer with each installation, Do not over-tighten.
6

Knock Sensor Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Torque sensor to the specified torque, avoid over-tightening.

Rotating Assembly

1

Connecting Rod Nuts

M10 x 1.5
Torque Specification
1. 15 ft-lbs (20 N·m) 2. 25 ft-lbs (34 N·m)
Important Notes
Torque in multiple steps, lubricate nuts and threads with engine oil.
2

Flywheel Bolts

M10 x 1.5
Torque Specification
78 ft-lbs (106 N·m)
Important Notes
These bolts are often torque-to-yield and may require replacement. Lubricate threads with oil. Torque in a star pattern.
3

Crankshaft Pulley/Harmonic Balancer Bolt

M16 x 2.0
Torque Specification
125 ft-lbs (169 N·m)
Important Notes
This bolt is typically a torque-to-yield and must be replaced. Lubricate threads and under head with engine oil, torque to spec.

Timing System

1

Timing Belt/Chain Tensioner Bolt

M8 x 1.25
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Ensure proper tensioner alignment. Torque to spec and confirm tension.
2

Camshaft Sprocket Bolt

M10 x 1.5
Torque Specification
43 ft-lbs (58 N·m)
Important Notes
Ensure correct camshaft timing before tightening. Torque to spec.

Intake System

1

Intake Manifold Bolts

M8 x 1.25
Torque Specification
14 ft-lbs (19 N·m)
Important Notes
Tighten in a criss-cross pattern to avoid air leaks. Confirm gasket seal.
2

Throttle Body Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Tighten evenly to ensure no vacuum leaks.
3

Fuel Injector Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Ensure injectors are properly seated. Torque bolts to spec.

Exhaust System

1

Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Tighten evenly to ensure a good seal, may require multiple passes. Use new gasket, torque to spec.

Cooling System

1

Water Pump Pulley Bolts

M6 x 1.0
Torque Specification
13 ft-lbs (18 N·m)
Important Notes
Torque evenly to avoid stressing the water pump.
2

Thermostat Housing Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Ensure the thermostat and gasket are properly seated. Torque evenly to prevent leaks.
3

Engine Coolant Temperature Sensor Bolt/Fitting

M10 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Ensure proper sealing, avoid over-tightening.

Accessory Drive

1

Serpentine/Accessory Drive Belt Tensioner Bolt

M10 x 1.5
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Ensure proper tensioner alignment before tightening. Torque to spec.
2

Drive Belt Idler Pulley Bolt

M10 x 1.5
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Ensure the pulley is properly aligned. Torque to spec.

Lubrication System

1

Oil Filter Cap Torque

N/A
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure o-ring seal is correctly installed. Torque to spec, do not over-tighten.

8hp Transmission

Torque specifications for 8hp Transmission

Transmission Mounting

1

Transmission Mounting Bolts (Bellhousing)

M12 x 1.75
Torque Specification
42 ft-lbs (57 N·m)
Important Notes
Torque in a star pattern. May require an additional angle torque, refer to the vehicle-specific manual. Always replace these bolts when removed.
2

Transmission Mounting Bolts (Chassis)

M10 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
These bolts are typically for mounting the transmission to the chassis crossmember or frame rails. Torque value is estimated, verify with the vehicle-specific service manual.

Oil Pan

1

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Torque in a criss-cross pattern. Overtightening may cause leaks.

Fluid Plugs

1

Transmission Drain Plug

M18 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Always replace sealing washer or O-ring. Overtightening could damage threads and cause leaks.
2

Transmission Fill Plug

M18 x 1.5
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Always replace sealing washer or O-ring. Overtightening could damage threads and cause leaks.

Mechatronic Unit

1

Mechatronic Unit Bolts (Valve Body)

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Torque in a criss-cross pattern. Overtightening can damage delicate components.

Torque Converter

1

Torque Converter Bolts

M10 x 1.25
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Torque in a star pattern. Always replace these bolts when removed.

Oil Cooler Lines

1

Oil Cooler Line Fitting (Inverted Flare)

Varies by Size (Estimate M16 x 1.5)
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Torque value is estimated, verify with vehicle-specific manual. Ensure proper alignment and sealing before tightening. Use a backup wrench when necessary. Can vary depending on the size of the fitting.
2

Oil Cooler Line Fitting (Banjo Bolt)

Varies by Size (Estimate M12 x 1.5)
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Torque value is estimated, verify with vehicle-specific manual. Ensure proper alignment and sealing before tightening. Replace sealing washers.

Output Flange

1

Transmission Output Flange Bolt

M12 x 1.75
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Torque value is an average, verify with vehicle specific manual. May vary depending on 2WD or 4WD application.

Body

Torque specifications for Body

Exterior Panels

1

Front Fender Mounting Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure even tightening to prevent panel distortion. Estimated value.
2

Rear Fender Mounting Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure even tightening to prevent panel distortion. Estimated value.
3

Hood Hinge Bolts (To Body)

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Proper torque is crucial for hood alignment and safe operation. Estimated value.
4

Hood Latch Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Incorrect torque can cause latching issues. Estimated value.
5

Door Hinge Bolts (To Body)

M10 x 1.5
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Proper torque ensures doors are securely mounted and operate correctly. Estimated value.
6

Door Latch Striker Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Proper torque is important for correct door closure and alignment. Estimated value.
7

Bumper Cover Bolts/Screws

M5 x 0.8
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Lower torque is necessary to avoid stripping plastic. Estimated value.
8

Headlight Assembly Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Proper torque ensures correct headlight alignment. Estimated value.
9

Taillight Assembly Mounting Bolts

M5 x 0.8
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Lower torque is required to avoid damage to plastic housings. Estimated value.
10

Grille Mounting Bolts/Screws

M5 x 0.8
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Low torque is important to avoid damage to plastic. Estimated value.
11

Side Mirror Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Proper torque is necessary for secure mounting without damaging door. Estimated value.
12

Rocker Panel Fasteners

M5 x 0.8
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Low torque is necessary to avoid damage to plastic. Estimated value.
13

Body Panel Mounts

M8 x 1.25
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Ensure proper mounting and body panel protection. Estimated value.

Roof And Glass

1

Sunroof Assembly Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Critical for secure sunroof operation. Estimated value.
2

Windshield Wiper Motor Mount Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
Proper torque ensures proper wiper operation. Estimated value.

Rear Hatch Trunk

1

Rear Hatch/Trunk Hinge Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Crucial for alignment and smooth operation. Estimated value.
2

Rear Hatch/Trunk Latch Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Vital for proper latching and alignment of the hatch/trunk. Estimated value.

Interior

1

Dashboard Mounting Bolts

M5 x 0.8
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Do not overtighten. Estimated value.
2

Seat Mounting Bolts

M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Critical for passenger safety. Estimated value.

Brakes

Torque specifications for Brakes

Brake Calipers

1

Brake Caliper Mounting Bolts

M12 x 1.5
Torque Specification
90 ft-lbs (122 N·m)
Important Notes
These bolts secure the caliper to the mounting bracket. Some models may use one-time-use bolts; always refer to the service manual.
2

Brake Caliper Mounting Bracket Bolts

M14 x 1.5
Torque Specification
100 ft-lbs (136 N·m)
Important Notes
These bolts secure the caliper mounting bracket to the wheel hub or suspension knuckle. Ensure proper seating of the bracket.
3

Brake Pad Retaining Pin/Bolt

M6 x 1.0
Torque Specification
12 ft-lbs (16 N·m)
Important Notes
Secures brake pads within the caliper. Torque value may vary; consult your specific service manual. Estimated value.
4

Brake Line Banjo Bolt

M10 x 1.0
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Secures the brake line to the caliper; use new crush washers. Estimated Value.
5

Brake Caliper Bleeder Screw

M7 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Used to bleed the brake system, avoid over-tightening. Estimated value.

Brake Discs

1

Brake Disc/Drum Retaining Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
These bolts secure the rotor to the wheel hub, Ensure the rotor is flush against the hub before tightening. Estimated Value

Wheel Mounting

1

Wheel Lug Nuts

M14 x 1.5
Torque Specification
95 ft-lbs (129 N·m)
Important Notes
Tighten in a star pattern to ensure even clamping force. Verify torque with a calibrated torque wrench.

Abs System

1

ABS Sensor Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Secures the ABS sensor to the suspension knuckle; avoid over-tightening. Estimated Value.

Drivetrain

Torque specifications for Drivetrain

Engine To Transmission

1

Flywheel Bolts

M12 x 1.5
Torque Specification
77.5 ft-lbs (105 N·m)
Important Notes
Ensure flywheel and crankshaft mating surfaces are clean and free of debris. Use new bolts if recommended by manufacturer.
2

Torque Converter Bolts/Nuts (Automatic Transmission)

M10 x 1.25
Torque Specification
1. 35 ft-lbs (47 N·m) 2. 90°
Important Notes
These bolts often require a torque and angle procedure. Ensure the torque converter is properly seated on transmission input shaft. If these are studs and nuts, torque the nuts to spec.
3

Clutch Pressure Plate Bolts (Manual Transmission)

M8 x 1.25
Torque Specification
1. 15 ft-lbs (20 N·m) 2. 25 ft-lbs (34 N·m) 3. 60°
Important Notes
These bolts often require multiple stages of torque, including a final angle measurement. Ensure the clutch disc and pressure plate are properly aligned. Install bolts finger tight in a star pattern.

Transmission Mounting

1

Transmission Mounting Bolts

M12 x 1.75
Torque Specification
42.5 ft-lbs (58 N·m)
Important Notes
Ensure the transmission is properly aligned with the engine block before tightening bolts. Use new bolts if recommended by manufacturer.
2

Input Shaft Seal Retainer Plate Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Tighten these bolts evenly to prevent damage to the seal. Over-tightening may cause leaks, while under-tightening can cause looseness.

Transmission Case

1

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Use a new gasket and tighten bolts in a crisscross pattern to ensure even pressure and prevent leaks. Check for leaks after refilling.
2

Transmission Drain and Fill Plugs

M18 x 1.5
Torque Specification
22.5 ft-lbs (30.5 N·m)
Important Notes
Use a new crush washer and avoid over-tightening. Check for leaks after refilling.

Driveshaft And Axles

1

Drive Axle/Half Shaft Bolts

M10 x 1.5
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Ensure the axle is fully seated on both the transmission/differential flange and wheel hub before tightening. Check that the axle is not binding before proceeding.
2

CV Joint/Axle Nut

M24 x 1.5
Torque Specification
190 ft-lbs (258 N·m)
Important Notes
This nut is high torque, it is very critical for proper connection and retaining the hub bearings. Use a new nut if recommended by manufacturer. Ensure the nut is tightened against the hub.
3

Propeller/Drive Shaft Bolts

M10 x 1.5
Torque Specification
52.5 ft-lbs (71 N·m)
Important Notes
Ensure the driveshaft is correctly aligned and centered before tightening. Some vehicles may require a driveshaft alignment procedure for vibrations.
4

Center Support Bearing Bolts (if applicable)

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
These bolts secure the center bearing support to the chassis. Ensure correct alignment before tightening.
5

Output Flange Nut

M27 x 1.5
Torque Specification
175 ft-lbs (237 N·m)
Important Notes
This nut retains the output flange and is critical to retain seals and bearings in place. It is a high torque fastener. Use new nut if recommended by manufacturer.

Differential

1

Differential Cover Bolts

M8 x 1.25
Torque Specification
22.5 ft-lbs (30.5 N·m)
Important Notes
Use a new gasket or sealant. Tighten bolts in a crisscross pattern to ensure even sealing and prevent leaks.
2

Differential Mounting Bolts

M12 x 1.75
Torque Specification
57.5 ft-lbs (78 N·m)
Important Notes
Ensure the differential is properly aligned with the chassis before tightening these bolts.
3

Differential Drain/Fill Plug

M18 x 1.5
Torque Specification
27.5 ft-lbs (37 N·m)
Important Notes
Use a new crush washer and avoid over-tightening. Check for leaks after refilling.

Transfer Case

1

Transfer Case Drain/Fill Plug

M18 x 1.5
Torque Specification
27.5 ft-lbs (37 N·m)
Important Notes
Use a new crush washer and avoid over-tightening. Check for leaks after refilling.

Electrical

Torque specifications for Electrical

Ignition System

1

Ignition Coil Mounting Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Ensure proper coil seating before tightening bolts. Torque to spec to ensure coil ground and proper function.

Starting System

1

Starter Motor Mounting Bolt

M10 x 1.5
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Tighten bolts evenly. Ensure the starter motor is properly aligned before tightening.

Charging System

1

Alternator Mounting Bolt

M8 x 1.25
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Ensure proper alternator alignment with the engine and belt is correctly installed before tightening. Tighten bolts evenly to prevent any stress.

Battery System

1

Battery Terminal Nut

M6
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Ensure terminals are clean before tightening. Do not over tighten, as this will damage the battery terminal or battery post.

Engine Control Unit

1

ECU Mounting Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Tighten evenly to ensure that the ECU is secure and making good contact with the vehicle chassis for grounding.

Ground Connections

1

Engine Ground Strap Bolt

M8 x 1.25
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure the ground strap makes good contact with both the engine and the body/chassis before tightening. Use proper star washers or serrated washers to maintain contact.
2

Chassis Ground Strap Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Ensure good contact and clean surfaces before tightening. Use proper star washers or serrated washers to maintain contact.
3

Wiring Harness Connector Ground Bolt

M5 x 0.8
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Ensure the ground connection is properly seated before tightening. Do not over tighten as these are small fasteners and are easily stripped.

Fuse Box

1

Fuse Box Mounting Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Tighten all fuse box mounting bolts evenly to prevent damage to the fuse box or its mounting points.

Sensors

1

Crankshaft Position Sensor Mounting Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Tighten to specified torque to ensure proper sensor seating and operation. Over tightening can damage the sensor.
2

Camshaft Position Sensor Mounting Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Tighten to specified torque to ensure proper sensor seating and operation. Over tightening can damage the sensor.
3

ABS Sensor Mounting Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Tighten to specified torque to ensure proper sensor seating and operation. Over tightening can damage the sensor.

Lighting

1

Headlight Mounting Bolt

M5 x 0.8
Torque Specification
5 ft-lbs (6.8 N·m)
Important Notes
Ensure proper alignment of the headlight before tightening the bolts. Do not over tighten the small fasteners as they are easily damaged.
2

Taillight Mounting Bolt

M5 x 0.8
Torque Specification
5 ft-lbs (6.8 N·m)
Important Notes
Ensure proper alignment of the taillight before tightening the bolts. Do not over tighten the small fasteners as they are easily damaged.

Emissions Sensors

Torque specifications for Emissions_sensors

Egr System

1

EGR Valve Mounting Bolts

M8 x 1.25
Torque Specification
13.5 ft-lbs (18.3 N·m)
Important Notes
Estimated value, check specific service manual for your exact model. Ensure a new gasket is used and that mounting surfaces are free of debris.

Exhaust System

1

Exhaust Manifold to Cylinder Head Bolts

M10 x 1.5
Torque Specification
22.5 ft-lbs (30.5 N·m)
Important Notes
Estimated value, torque in a sequence recommended by the manufacturer to ensure even pressure distribution. Always use new gaskets.
2

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
27.5 ft-lbs (37.3 N·m)
Important Notes
Ensure mounting surfaces are free of debris. Use new gaskets or sealant as appropriate. Estimated value.
3

Muffler to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
27.5 ft-lbs (37.3 N·m)
Important Notes
Use new gaskets or sealant as appropriate, estimated value. Ensure mating surfaces are clean and not damaged.

Oxygen Sensors

1

Pre-Catalytic Converter Oxygen Sensor Mounting

M18 x 1.5
Torque Specification
17.5 ft-lbs (23.7 N·m)
Important Notes
Estimated value. Do not overtighten. Ensure sensor threads are clean, and use anti-seize compound on threads if necessary.
2

Pre-Catalytic Converter Oxygen Sensor Mounting

M12 x 1.25
Torque Specification
11 ft-lbs (14.9 N·m)
Important Notes
Estimated value. Do not overtighten. Ensure sensor threads are clean, and use anti-seize compound on threads if necessary.
3

Post-Catalytic Converter Oxygen Sensor Mounting

M18 x 1.5
Torque Specification
17.5 ft-lbs (23.7 N·m)
Important Notes
Estimated value. Do not overtighten. Ensure sensor threads are clean, and use anti-seize compound on threads if necessary.
4

Post-Catalytic Converter Oxygen Sensor Mounting

M12 x 1.25
Torque Specification
11 ft-lbs (14.9 N·m)
Important Notes
Estimated value. Do not overtighten. Ensure sensor threads are clean, and use anti-seize compound on threads if necessary.

Intake System Sensors

1

Mass Air Flow (MAF) Sensor Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Estimated value, do not overtighten. Ensure mounting surfaces are clean and free from obstructions. Use a new o-ring or seal if applicable.
2

Intake Air Temperature (IAT) Sensor Mounting Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Estimated value. Do not overtighten the IAT sensor. Inspect sensor and mounting location for damage. Ensure a new o-ring or seal if applicable.

Nox Sensor

1

Nitrogen Oxide (NOx) Sensor Mounting Bolts/Studs/Nuts

M6 x 1.0
Torque Specification
11 ft-lbs (14.9 N·m)
Important Notes
Estimated value. Ensure all mating surfaces are clean and free of debris. Use new gaskets or sealing surfaces when available.

Egt Sensor

1

Exhaust Gas Temperature (EGT) Sensor Mounting Bolts/Studs/Nuts

M6 x 1.0
Torque Specification
11 ft-lbs (14.9 N·m)
Important Notes
Estimated value. Ensure all mating surfaces are clean and free of debris. Use new gaskets or sealing surfaces when available.

Evap System

1

Vapor Canister Purge Valve Mounting Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12.2 N·m)
Important Notes
Estimated value. Do not overtighten. Ensure mounting surfaces are clean, and that the purge valve is fitted with a proper seal. Overtightening can damage the purge valve.
2

Vapor Canister Mounting Bolts

M8 x 1.25
Torque Specification
11 ft-lbs (14.9 N·m)
Important Notes
Estimated value. Ensure canister mounting points are not damaged. Do not overtighten.
3

EVAP Line Fittings

N/A
Torque Specification
13.5 ft-lbs (18.3 N·m)
Important Notes
Estimated value for threaded fittings. Do not overtighten. Ensure fittings are properly aligned before tightening. Use backup wrenches when tightening lines.

Exhaust

Torque specifications for Exhaust

Exhaust Manifold

1

Exhaust Manifold to Cylinder Head Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Tighten bolts in a criss-cross pattern to ensure even clamping pressure. Estimated value based on typical M8 bolt torque.
2

Exhaust Pipe to Exhaust Manifold/Header Bolts/Studs

M10 x 1.5
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Ensure proper alignment before tightening. Estimated value based on typical M10 bolt torque.

Catalytic Converter

1

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Ensure a new gasket is used to prevent leaks. Estimated value based on typical M10 bolt torque.

Muffler

1

Muffler to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Ensure proper alignment and use new fasteners (bolts/nuts). Estimated value based on typical M10 bolt torque.

Exhaust Hangers

1

Exhaust Hanger/Bracket Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
These bolts secure the exhaust hangers to the chassis; ensure proper alignment to support the exhaust system. Estimated value based on typical M8 bolt torque.

Exhaust Clamps

1

Exhaust Clamp Bolts (Small Diameter)

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
For smaller exhaust pipe connections. Be careful not to over-tighten to prevent crushing the pipes. Estimated value based on typical M8 bolt torque.
2

Exhaust Clamp Bolts (Large Diameter)

M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
For larger exhaust pipe connections; ensure a secure seal without pipe deformation. Estimated value based on typical M10 bolt torque.

Oxygen Sensor

1

Oxygen Sensor

M18 x 1.5
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Apply anti-seize compound to the threads. Do not overtighten to avoid damage to the sensor or threads. Estimated value based on typical O2 sensor torque.

Fuel

Torque specifications for Fuel

Fuel Rail

1

Fuel Rail Mounting Bolts

M8 x 1.25
Torque Specification
13 ft-lbs (18 N·m)
Important Notes
Ensure fuel rail O-rings are properly seated. Torque value is an estimate; consult manufacturer service manual for specific values.
2

Fuel Pressure Sensor Mounting Bolt

M5 x 0.8
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Small bolt; do not overtighten. Torque value is an estimate.

Fuel Injectors

1

Fuel Injector Mounting Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Ensure proper seating of injector O-rings. Torque value is an estimate.

Fuel Pump

1

Fuel Pump Mounting Bolts

M8 x 1.25
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Ensure proper pump seal seating. Torque value is an estimate.

Fuel Tank

1

Fuel Tank Strap Bolts

M12 x 1.75
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Tighten evenly to prevent tank movement. Torque value is an estimate.
2

Fuel Filler Neck Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Ensure proper sealing of the filler neck. Torque value is an estimate.
3

Fuel Tank Access Panel Bolts

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Do not overtighten, as panel can be damaged. Torque value is an estimate.

Fuel Filter

1

Fuel Filter Mounting Bolts/Nuts

M8 x 1.25
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Ensure filter is held securely to vehicle frame. Torque value is an estimate.

Fuel Lines

1

Fuel Line Fittings (Banjo Bolts)

M12 x 1.5
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Torque value is an estimate, may vary depending on fitting type and size. Use new sealing washers.

Hvac

Torque specifications for Hvac

Ac Compressor

1

A/C Compressor Mounting Bolts

M8 x 1.25
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Tighten bolts evenly to specified torque. Ensure all bolts are fully engaged before tightening. Use a criss-cross pattern to evenly distribute pressure.

Ac Lines And Fittings

1

A/C Line Fittings (Threaded)

M8 x 1.0
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Ensure O-rings are properly lubricated and in good condition before assembly. Over-tightening can damage fittings and O-rings.
2

A/C Line Fittings (Flange)

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten bolts evenly to specified torque. Ensure all bolts are fully engaged before tightening. Use a criss-cross pattern to evenly distribute pressure.

Ac Condenser

1

A/C Condenser Mounting Bolts/Nuts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Condenser is typically mounted using rubber bushings. Avoid over-tightening to prevent damage to the condenser or bushings. Use a criss-cross pattern when tightening multiple fasteners.

Ac Evaporator

1

A/C Evaporator Core Housing Bolts

M5 x 0.8
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
The housing is typically plastic; over-tightening can crack or distort the housing. Apply torque evenly to prevent leaks.

Blower Motor

1

HVAC Blower Motor Mounting Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (9 N·m)
Important Notes
The blower motor housing is typically plastic, avoid overtightening which could damage the housing or cause vibration. Tighten bolts evenly to specified torque. Ensure all bolts are fully engaged before tightening. Use a criss-cross pattern to evenly distribute pressure.

Heater Core

1

Heater Core Mounting Bolts/Clamps

M5 x 0.8
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Heater core is often made of delicate aluminum or brass, be careful not to damage the core. Over-tightening can lead to leaks or damage.

Control Module Actuators

1

HVAC Control Module/Actuator Mounting Screws

M4 x 0.7
Torque Specification
3 ft-lbs (4 N·m)
Important Notes
Components are typically plastic; over-tightening can crack or damage the plastic housing. Ensure proper electrical connections before full tightening.

Ductwork

1

HVAC Ductwork Mounting Screws/Bolts

M4 x 0.7
Torque Specification
3 ft-lbs (4 N·m)
Important Notes
Ductwork components are typically plastic. Over-tightening can cause cracking and air leaks. Ensure proper fitment to prevent air gaps.

Suspension

Torque specifications for Suspension

Front Suspension

1

Strut/Shock Absorber Mounting Bolts

M14 x 1.5
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Secures the strut assembly to the chassis or knuckle. Tighten bolts evenly in a star pattern.
2

Front Lower Control Arm to Subframe Bolt

M14 x 2.0
Torque Specification
130 ft-lbs (176 N·m)
Important Notes
High-load bolt; ensure proper torque to prevent control arm movement. Estimated value.
3

Upper Strut Mount Bolts (to Body)

M8 x 1.25
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Secures the upper strut mount to the vehicle chassis. Estimated value.
4

Ball Joint Nut

M12 x 1.5
Torque Specification
53 ft-lbs (72 N·m)
Important Notes
Secures the ball joint stud to the control arm or knuckle.
5

Strut Pinch Bolt(s)

M12 x 1.75
Torque Specification
58 ft-lbs (79 N·m)
Important Notes
Secures the strut to the steering knuckle. Tighten evenly.

Rear Suspension

1

Rear Lower Control Arm to Subframe Bolt

M14 x 2.0
Torque Specification
110 ft-lbs (149 N·m)
Important Notes
High-load bolt; ensure proper torque to prevent control arm movement. Estimated value.

Steering

1

Tie Rod End Nut

M12 x 1.25
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Secures the tie rod end to the steering knuckle.

Stabilizer

1

Sway Bar Link Nut

M10 x 1.5
Torque Specification
38 ft-lbs (51 N·m)
Important Notes
Secures the sway bar link to the sway bar and strut or control arm.

Wheel Mounting

1

Wheel Lug Nuts

M14 x 1.25
Torque Specification
95 ft-lbs (129 N·m)
Important Notes
Tighten lug nuts in a star pattern.

Drivetrain

1

Axle Shaft to Wheel Hub Bolt

M10 x 1.25
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Secures the axle shaft to the wheel hub. Estimated value.

Troubleshooting Guide

Common issues, diagnostic steps, and prevention guidelines

Common Issues

Bolt stretching, stripped threads, uneven torque patterns

Loose Components

Symptoms:
  • Rattling or vibration noises
  • Visible movement in components
  • Uneven panel gaps
Solutions:
  • Clean threads and mounting surfaces
  • Replace damaged fasteners
  • Apply proper torque in sequence
  • Use thread locker if specified

Stripped Fasteners

Symptoms:
  • Unable to achieve proper torque
  • Fastener spins freely
  • Visible thread damage
Solutions:
  • Use thread repair kit if appropriate
  • Install thread insert (HeliCoil)
  • Replace component if threaded hole is damaged
  • Upgrade to higher grade fastener if recommended

Overtightened Components

Symptoms:
  • Cracked or deformed parts
  • Broken fasteners
  • Compressed gaskets or seals
Solutions:
  • Replace damaged components
  • Use new fasteners
  • Follow proper torque sequence
  • Verify correct torque specifications

Diagnostic Steps

Visual inspection, torque verification, thread assessment

1

Visual Inspection

Inspect the affected area for any visible signs of damage or wear

  • Check for cracks or deformation
  • Look for signs of excessive wear
  • Verify proper fastener installation
2

Torque Verification

Verify the torque applied to the fasteners

  • Check the torque wrench calibration
  • Verify the torque specification
  • Compare the applied torque to the specification
3

Thread Assessment

Assess the condition of the threads

  • Check for signs of thread damage
  • Verify the thread type and size
  • Check for proper thread engagement

Prevention Guidelines

Best practices, maintenance tips, tool care

Best Practices

  • Always follow the recommended torque specification
  • Use the correct type and size of fasteners
  • Verify the torque wrench calibration regularly

Maintenance Tips

  • Regularly inspect the affected area for signs of wear or damage
  • Replace damaged or worn-out components promptly
  • Keep the work area clean and organized

Tool Care

  • Regularly clean and maintain the torque wrench
  • Store the torque wrench in a dry and secure location
  • Verify the torque wrench calibration before each use

Frequently Asked Questions

Find answers to common questions about torque specifications

Q1

What IS the recommended torque specification for the cylinder head bolts on a 2017 BMW 530i?

The cylinder head bolts on a 2017 BMW 530i require a torque of 20 Nm (15 ft-lb) for the first step, followed by 70 Nm (52 ft-lb) plus an additional 90 degrees for the final step.

Q2

What IS the proper tightening sequence for the lug nuts on a BMW 530i?

BMW recommends tightening the lug nuts in a star pattern, starting with the nut that IS directly opposite the valve stem. Tighten the lug nuts to 140 Nm (103 ft-lb) using a calibrated torque wrench.

Q3

What type of torque wrench should I use for critical components on my BMW 530i?

BMW recommends using a calibrated, click-type torque wrench for critical components such as cylinder head bolts, connecting rod bolts, and crankshaft bolts. Ensure that the torque wrench IS within its specified calibration range.

Q4

IS it safe to use an impact wrench for tightening bolts on my BMW 530i?

BMW generally advises against using an impact wrench for tightening bolts, as it can lead to overtightening and potential damage to the components. Use a calibrated torque wrench instead for precise torque application.

Q5

What are the consequences of overtightening or undertightening bolts on my BMW 530i?

Overtightening can cause thread damage, bolt failure, or component distortion. Undertightening can result in loose bolts, compromised joint integrity, and potential safety hazards.

Environmental Considerations

Temperature, humidity, and seasonal effects on torque specifications

Temperature Effects

Includes: High Heat, Cold Weather, Thermal Cycling

Temperature can significantly impact torque values and fastener behavior

Cold Weather

Effects:
  • Increased material brittleness
  • Higher torque required due to thread contraction
  • Reduced thread lubricant effectiveness
Recommendations:
  • Allow components to warm to room temperature when possible
  • Consider using winter-grade thread lubricants
  • Check torque values more frequently during winter months

Hot Weather

Effects:
  • Thermal expansion of components
  • Decreased friction in threads
  • Accelerated lubricant breakdown
Recommendations:
  • Check torque when components are at normal operating temperature
  • Use temperature-resistant thread lockers
  • Consider re-torquing after heat cycles

Humidity and Corrosion

Covers: Rust Prevention, Salt Exposure, Moisture Control

Moisture and corrosion can affect fastener integrity and torque values

High Humidity

Effects:
  • Accelerated corrosion formation
  • Reduced friction coefficient
  • Potential thread seizing
Prevention:
  • Use corrosion-resistant fasteners
  • Apply appropriate anti-seize compounds
  • Maintain proper protective coatings

Salt Exposure

Effects:
  • Rapid corrosion development
  • Thread damage
  • Seized fasteners
Prevention:
  • Regular underbody washing
  • Use of sacrificial anodes where appropriate
  • Application of protective coatings

Seasonal Maintenance

Spring, Summer, Fall, and Winter maintenance schedules

Spring

  • Inspect for winter damage
  • Clean and protect exposed fasteners
  • Check torque on critical components

Summer

  • Monitor heat-affected components
  • Check expansion-related loosening
  • Inspect cooling system mounts

Fall

  • Prepare for winter conditions
  • Apply corrosion protection
  • Verify all fasteners are properly torqued

Winter

  • More frequent inspection of critical fasteners
  • Check for salt damage
  • Monitor suspension component torque

Related Resources

Tools, service procedures, and technical bulletins

Recommended Tools

Digital Torque Wrench (10-100 Nm)

Essential for tightening fasteners to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the 530i.

  • Digital display for accurate readings
  • Audible alarm when target torque IS reached
  • Multiple units (Nm, ft-lb, in-lb)
  • Reversible ratcheting mechanism
Learn more
Service Procedures

Engine Oil Filter Housing Bolt Replacement

Procedure for replacing the 32 Nm oil filter housing bolt on the BMW 530i.

  • Locate the oil filter housing on the top of the engine.
  • Use a 32 Nm torque wrench to loosen the oil filter housing bolt.
  • Replace the oil filter cartridge and tighten the bolt to 25 Nm.
  • Start the engine and check for oil leaks.
View full procedure

Suspension Control Arm Bolt Tightening

How to tighten the suspension control arm bolts to 120 Nm plus 90 degrees on the BMW 530i.

  • Raise the vehicle and remove the wheel.
  • Locate the suspension control arm bolts and loosen them.
  • Tighten the bolts to 120 Nm using a torque wrench.
  • Rotate the bolts an additional 90 degrees using an angle gauge.
View full procedure

Spark Plug Replacement

Guide to replacing the spark plugs and tightening them to 25 Nm on the BMW 530i.

  • Remove the ignition coils and unscrew the old spark plugs.
  • Apply anti-seize to the threads of the new spark plugs.
  • Tighten the new spark plugs to 25 Nm using a torque wrench.
  • Reinstall the ignition coils and start the engine.
View full procedure
Technical Service Bulletins

Service Bulletin: Incorrect Engine Oil Filter Housing Bolt Torque

2018-10-01

Service bulletin addressing the incorrect 25 Nm torque specification for the oil filter housing bolt on 2017-2018 530i models, leading to potential oil leaks. The correct torque IS 32 Nm.

2017-2018 530i

Resolution: Dealers are instructed to retorque the oil filter housing bolt to 32 Nm on affected vehicles.

Service Bulletin: Steering Gear Mounting Bolt Recall

2021-06-22

Recall notice regarding a loose steering gear mounting bolt on certain 2017-2019 530i models. The loose bolt can lead to reduced steering control and increased risk of accidents.

2017-2019 530i (specific production dates)

Resolution: Owners are advised to bring their vehicles to an authorized BMW dealership to have the steering gear mounting bolts inspected and tightened to the correct torque specification.

Legal Disclaimer

Important information about using this content

Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.

General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability

The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.

We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.

Technical Information
  • All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
  • Vehicle specifications and procedures may vary by model year, trim level, and region.
  • Always follow the manufacturer's recommended procedures and safety precautions.
  • Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
  • If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.

About the Author

Expert automotive knowledge and experience

Alan Montanye - Automotive Technical Specialist
ASE

Alan Montanye

Automotive Technical Specialist

ASE Master Certified Technician with over a decade of hands-on experience in automotive repair and diagnostics.

Facebook Contact
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions

Diagnostic

Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.

Repair

Expert in both traditional mechanical repairs and modern vehicle systems.

Additional Expertise

Documentation

Created over 500 detailed repair guides and technical documents.

Training

Conducted technical training sessions and contributed to repair databases.

Certifications & Research

Certifications

  • ASE Master Technician Certification
  • Advanced Diagnostic Specialist
  • Hybrid/Electric Vehicle Systems
  • Performance Tuning Expert

Research & Community

Actively researches emerging technologies and contributes to automotive forums.

© 2025 BMW Specs. All rights reserved.

Privacy Policy Terms of Service