BMW Vehicle Models 430i 2017-present Torque Specifications
BMW Vehicle Models 430i 2017-present

BMW Vehicle Models 430i 2017-present Torque Specifications

Complete BMW Vehicle Models 430i 2017-present torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.

Updated

Important Information

Safety guidelines and reference information for proper torque application

Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083

Common Torque Patterns

Star Pattern

Used for wheels and other circular bolt patterns

Star Pattern torque pattern diagram showing proper bolt tightening sequence
Cross Pattern

Used for gaskets and cover plates

Cross Pattern torque pattern diagram showing proper bolt tightening sequence
Sequential Pattern

Used for head bolts and other critical components

Sequential Pattern torque pattern diagram showing proper bolt tightening sequence

Common Mistakes to Avoid

Over-tightening

Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.

Prevention:

Always use a calibrated torque wrench and follow specifications exactly.

Incorrect Torque Sequence

Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.

Prevention:

Follow the manufacturer's specified torque sequence pattern.

Dirty Threads

Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.

Prevention:

Clean and inspect all threads before assembly. Use new thread locker if specified.

Reusing TTY Bolts

Torque-to-yield bolts are designed to stretch and must not be reused.

Prevention:

Always replace TTY bolts with new ones. They are single-use only.

Dry vs. Lubricated

Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.

Prevention:

Check if specs are for dry or lubricated threads. Use specified lubricant when required.

Recommended Tools

Torque Wrench (1/4" Drive)

Range: 2-25 ft-lbs
Small fasteners, delicate components

Torque Wrench (3/8" Drive)

Range: 10-100 ft-lbs
Most common automotive fasteners

Torque Wrench (1/2" Drive)

Range: 30-250 ft-lbs
Large fasteners, wheels

Angle Gauge

Torque-to-yield (TTY) bolts

Torque Wrench Care

  • Calibrate annually or after 5,000 clicks
  • Store at lowest setting
  • Keep clean and lubricated

Search Specifications

Search by component name, bolt size, or description

Torque Calculator

Convert between different torque units

2.0l Engine

Torque specifications for 2.0L Engine

Cylinder Head

1

Cylinder Head Bolts

M10 x 1.5
Torque Specification
1. 22 ft-lbs (30 N·m) 2. 90° 3. 90°
Important Notes
Tighten in specified sequence. Final torque values should be achieved through the angle method after the initial torque.
2

Cylinder Head Dowel Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
These dowel bolts are for alignment and should be tightened after the main head bolts initial torque.

Engine Block

1

Main Bearing Bolts

M12 x 1.5
Torque Specification
1. 44 ft-lbs (60 N·m) 2. 70°
Important Notes
Tighten in a specific sequence. Angle tightening is required.
2

Oil Pan Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Low torque to avoid damage to the oil pan or gasket. Tighten in a criss-cross pattern.
3

Crankshaft Position Sensor Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure proper sensor alignment.
4

Knock Sensor Bolt

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Proper torque ensures accurate knock detection.
5

Oil Filter Housing Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper seal.
6

Oil Drain Plug Bolt

M14 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Use a new crush washer for proper sealing.
7

PCV Valve Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure proper mounting and sealing.
8

Belt Tensioner Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Properly secure the tensioner to the engine block.
9

Idler Pulley Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure correct alignment and secure mounting.

Crankshaft

1

Connecting Rod Nuts

M9 x 1.25
Torque Specification
1. 22 ft-lbs (30 N·m) 2. 50°
Important Notes
Tighten in two steps, the final step requiring an angle torque.
2

Flywheel Bolts

M12 x 1.5
Torque Specification
1. 61 ft-lbs (83 N·m) 2. 60°
Important Notes
Tighten in a star pattern, use new bolts, and the final step requires an angle.
3

Crankshaft Pulley/Harmonic Balancer Bolt

M18 x 1.5
Torque Specification
1. 81 ft-lbs (110 N·m) 2. 90°
Important Notes
Tighten using two steps, the final requires an angle. Ensure proper alignment of the pulley.

Valve Train

1

Valve Cover Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten in a criss-cross pattern to avoid warping or gasket damage.
2

Timing Belt/Chain Tensioner Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper belt/chain tension is achieved after tightening.
3

Camshaft Sprocket Bolt

M10 x 1.5
Torque Specification
63 ft-lbs (85 N·m)
Important Notes
Ensure proper camshaft timing alignment.
4

Camshaft Position Sensor Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure proper sensor alignment and connection.
5

Rocker Arms/Shafts Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Tighten in a specified sequence. Proper torque ensures proper valve actuation.
6

Variable Valve Timing (VANOS) Solenoid Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure proper solenoid alignment and function.

Fuel System

1

Fuel Rail Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure proper fuel rail alignment and sealing.
2

Fuel Injector Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure injectors are properly seated in the intake manifold.
3

High Pressure Fuel Pump Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Secure the high-pressure fuel pump to the engine.

Intake Exhaust

1

Throttle Body Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure the throttle body is properly aligned.
2

Intake Manifold Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten in a specific sequence to ensure even clamping force.
3

Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Use a new gasket for proper sealing. Tighten using a criss-cross pattern
4

EGR Valve Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Proper sealing is important for emission control.
5

Intake Air Temperature Sensor Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure proper sensor function.

Cooling System

1

Water Pump Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure proper alignment to prevent leaks.
2

Water Pump Pulley Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Securely mount the pulley to the pump.
3

Thermostat Housing Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure a good seal to prevent coolant leaks.
4

Coolant Temperature Sensor Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure proper sensor alignment and sealing.

Ignition System

1

Spark Plugs

M14 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Do not over-tighten, proper torque is essential for a good seal.
2

Ignition Coil Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure a secure electrical connection.

Turbocharger System

1

Turbocharger Oil Feed Line Bolts/Banjo Bolts

M10 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use new sealing washers and ensure no leaks.
2

Turbocharger Coolant Feed/Return Line Bolts/Banjo Bolts

M10 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use new sealing washers and ensure no leaks.
3

Turbocharger Mounting Bolts to Exhaust Manifold

M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure proper turbocharger alignment and sealing.
4

Turbocharger Mounting Bolts to Engine Block

M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure proper turbocharger alignment and secure mounting.

8hp Transmission

Torque specifications for 8hp Transmission

Transmission Mounting

1

Transmission Mounting Bolts

M12 x 1.75
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Bolt size may vary. Consult vehicle-specific manual. Apply even torque across all bolts.

Transmission Oil Pan

1

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Use a criss-cross pattern for even tightening. Ensure pan gasket is properly installed. Do not over-tighten, which could cause leaks or damage.

Fluid Plugs

1

Transmission Drain/Fill Plugs

M18 x 1.5
Torque Specification
29 ft-lbs (39 N·m)
Important Notes
Always use a new crush washer. Over-tightening may damage threads or cause leaks. Clean the plug and its mating surface prior to installation

Mechatronic Unit

1

Mechatronic Unit Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Use a specific tightening sequence as specified in the service manual. Avoid over-tightening as it may cause leaks. Apply even torque across all bolts.

Valve Body

1

Valve Body Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Use a specific torque pattern to tighten the bolts. Improper torque can lead to leaks or malfunction. Apply even torque across all bolts.

Transmission Housing

1

Transmission Housing Bolts

M10 x 1.5
Torque Specification
1. 41 ft-lbs (55 N·m) 2. 90°
Important Notes
These may be torque-to-yield bolts. Always replace upon removal. Tighten in a specified sequence. Use a torque angle meter for final angle tightening. Always refer to the vehicle-specific service manual.

Output Flange

1

Transmission Output Flange Bolt

M10 x 1.5
Torque Specification
1. 33 ft-lbs (45 N·m) 2. 60°
Important Notes
Use a specific torque pattern. Use a torque angle meter for the final 60 degree turn. Always refer to the vehicle's specific service manual.

Torque Converter

1

Torque Converter to Flywheel Bolts

M10 x 1.25
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Tighten bolts evenly in a star pattern. Ensure proper converter alignment. Over-tightening may damage the converter or flywheel.

Internal Filter

1

Internal Transmission Filter Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure the filter is correctly positioned. Use a criss-cross pattern for even tightening. Apply even torque across all bolts.

Body

Torque specifications for Body

Wheel And Suspension

1

Wheel Lug Nuts

M14 x 1.25
Torque Specification
103 ft-lbs (140 N·m)
Important Notes
Tighten in a star pattern to ensure even clamping force.

Fuel System

1

Fuel Tank Strap Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the fuel tank is properly positioned before tightening.
2

Fuel Filler Neck Bolts

M6 x 1.0
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure proper seal alignment before tightening to prevent leaks

Electrical System

1

Battery Terminal Nuts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Do not overtighten to prevent damage to battery terminals. Clean terminals before connection.

Body Panels And Closures

1

Hood Hinge Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper hood alignment before fully tightening.
2

Fender Mounting Bolts/Screws

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure fender is properly aligned before tightening.
3

Door Hinge Bolts

M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Ensure correct door alignment and smooth operation after tightening.
4

Door Latch/Striker Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper latch engagement and smooth door operation.
5

Trunk/Hatch Hinge Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure proper trunk/hatch alignment and smooth operation.

Exterior Trim

1

Bumper Cover Mounting Bolts/Screws

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure bumper cover is flush and properly aligned before final tightening.
2

Headlight/Taillight Mounting Bolts/Screws

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure proper alignment and fit of the lights.
3

Side Skirt/Rocker Panel Bolts/Screws

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure the skirt/panel is flush against the body before tightening.

Interior

1

Seat Mounting Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Tighten bolts evenly to ensure proper seat alignment and stability. These bolts are critical for occupant safety.
2

Dashboard/Instrument Panel Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure the panel is flush against the body and no wires or connectors are pinched.

Brakes

Torque specifications for Brakes

Brake Calipers

1

Caliper Mounting Bolts

M12 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
These high-strength bolts secure the caliper directly to the mounting bracket. Ensure bolts are replaced if removed, as they may be stretch bolts. Torque in a crisscross pattern.
2

Caliper Guide Pin Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
These bolts secure the caliper to its sliding guide pins. Estimated value, always check the specific repair manual for your model. Do not over-tighten.
3

Brake Hose Banjo Bolt

M10 x 1.0
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Connects the brake line to the caliper. Use new crush washers. Estimated value; consult the repair manual. Do not over-tighten.

Caliper Mounting Bracket

1

Mounting Bracket Bolts

M14 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
These high-strength bolts secure the bracket to the hub/knuckle. Always replace if removed as they may be torque to yield. Torque in a crisscross pattern.

Brake Rotors

1

Rotor Retaining Bolts/Screws

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
These screws hold the rotor to the hub. Often low torque. These ensure proper rotor alignment and prevent movement before the wheel is installed. Some rotors may not have these.

Wheel Mounting

1

Wheel Lug Nuts

M14 x 1.25
Torque Specification
103 ft-lbs (140 N·m)
Important Notes
Tighten in a star pattern. Ensure proper clamping force to the rotor. Failure to torque properly can cause wheel and brake system damage or failure.

Brake Pad Sensor

1

Brake Pad Wear Sensor Screw/Bolt

M4 x 0.7
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Small screw securing the wear sensor to the pad. Estimated value, do not over tighten. Only tighten enough to hold sensor securely.

Drivetrain

Torque specifications for Drivetrain

Engine Flywheel

1

Flywheel Bolts

M12 x 1.25
Torque Specification
61 ft-lbs (83 N·m)
Important Notes
Use new bolts. Apply threadlocker. Ensure the flywheel is properly aligned before tightening.

Transmission Mounting

1

Transmission-to-Engine/Bellhousing Bolts

M12 x 1.75
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Tighten in a cross pattern to ensure even clamping pressure. Verify proper alignment before tightening.
2

Transmission Mounting Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure transmission is properly supported before tightening. These are typically smaller bolts going to chassis mounts.

Transmission Service

1

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten in a criss-cross pattern to ensure even seal. Use new gasket/seal.
2

Transmission Drain and Fill Plugs

M18 x 1.5
Torque Specification
29 ft-lbs (39 N·m)
Important Notes
Use new sealing washer. Do not over-tighten.

Driveshaft

1

Propeller/Drive Shaft Bolts

M10 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Ensure proper alignment before tightening. Use threadlocker on bolts.
2

Flex Disc (Guibo) Bolts

M12 x 1.5
Torque Specification
1. 44 ft-lbs (60 N·m) 2. 90°
Important Notes
Use new bolts. Tighten to specified torque then rotate an additional 90 degrees. Follow specific sequence if applicable.
3

Driveshaft Center Support Bearing Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Do not overtighten these bolts. Ensure bearing is properly positioned before tightening.

Axles And Cv Joints

1

Drive Axle/Half Shaft Bolts

M10 x 1.5
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Use new bolts where specified. Ensure proper seating of axle to hub/differential flange before tightening.
2

CV Joint/Axle Nut

M24 x 1.5
Torque Specification
185 ft-lbs (250 N·m)
Important Notes
Use a new nut. Tighten nut when vehicle is on the ground (under load), after initial wheel installation.

Differential

1

Differential Mounting Bolts

M12 x 1.75
Torque Specification
52 ft-lbs (70 N·m)
Important Notes
Tighten bolts in a cross pattern. Ensure proper differential alignment before tightening.
2

Differential Drain/Fill Plug

M22 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Use a new sealing washer on the plug.
3

Output Flange Nut on Differential

M20 x 1.5
Torque Specification
135 ft-lbs (183 N·m)
Important Notes
Use new nut. Ensure proper flange alignment before tightening. Estimated value.

Transfer Case

1

Transfer Case Drain/Fill Plug

M18 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Use new sealing washer. Do not over-tighten
2

Output Flange Nut on Transfer Case

M20 x 1.5
Torque Specification
135 ft-lbs (183 N·m)
Important Notes
Use new nut. Ensure proper flange alignment before tightening. Estimated value.

Electrical

Torque specifications for Electrical

Ignition System

1

Ignition Coil Mounting Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure proper coil seating before tightening. Over-tightening may damage the coil or cylinder head.

Starting System

1

Starter Motor Mounting Bolt

M10 x 1.5
Torque Specification
32 ft-lbs (43 N·m)
Important Notes
Ensure the starter motor is properly aligned before tightening. Over-tightening may damage the starter or engine block. Bolts may be different lengths, ensure correct placement.

Charging System

1

Alternator Mounting Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper belt tension is maintained during tightening. Over-tightening may cause alternator bearing or mounting bracket damage.

Battery System

1

Battery Terminal Nut

M6
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Do not over-tighten the terminals. Over-tightening can damage the terminals or battery post, causing poor connections. Check for proper terminal engagement before tightening. Always disconnect the negative terminal before the positive when removing battery cables, and reconnect positive before negative.

Engine Control Unit

1

ECU Mounting Bolt/Nut

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure proper ECU seating before tightening. Over-tightening may damage the ECU case or mounting points.

Ground Connections

1

Ground Strap Mounting Bolt/Nut (Engine Bay)

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure clean, unpainted contact surfaces for proper grounding. Over-tightening may damage the grounding point or bolt/nut. Clean grounding surfaces before installation and ensure correct strap placement.
2

Ground Strap Mounting Bolt/Nut (Chassis)

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure clean, unpainted contact surfaces for proper grounding. Over-tightening may damage the chassis or bolt/nut. Clean grounding surfaces before installation and ensure correct strap placement.
3

Ground Strap Mounting Bolt/Nut (Body)

M6 x 1.0
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure clean, unpainted contact surfaces for proper grounding. Over-tightening may damage the body panel or bolt/nut. Clean grounding surfaces before installation and ensure correct strap placement. This is an estimated value.

Sensor Mounting

1

Crankshaft Position Sensor Mounting Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Ensure proper sensor alignment and seating before tightening. Over-tightening may damage the sensor housing or mounting point. This is an estimated value.
2

Camshaft Position Sensor Mounting Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Ensure proper sensor alignment and seating before tightening. Over-tightening may damage the sensor housing or mounting point. This is an estimated value.
3

ABS Sensor Mounting Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Ensure proper sensor alignment and seating before tightening. Over-tightening may damage the sensor housing or mounting point. This is an estimated value.
4

Wheel Speed Sensor Mounting Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Ensure proper sensor alignment and seating before tightening. Over-tightening may damage the sensor housing or mounting point. This is an estimated value.

Power Distribution

1

Fuse Box/Power Distribution Box Mounting Bolt/Screw

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure proper alignment of the box before tightening. Over-tightening can damage the box housing or mounting points.

Wiring Harness

1

Wiring Harness Connector Retaining Screw/Bolt

M4 x 0.7
Torque Specification
3 ft-lbs (4 N·m)
Important Notes
Ensure proper connector engagement before tightening. Over-tightening can damage the connector or housing. Use an inch pound torque wrench for best results, or torque by hand with care. This is an estimated value.

Emissions Sensors

Torque specifications for Emissions_sensors

Exhaust System

1

Exhaust Manifold to Cylinder Head Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Tighten in a spiral pattern starting from the center.
2

Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Tighten in a spiral pattern starting from the center.
3

Exhaust Pipe to Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure proper alignment before tightening.
4

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Check for proper flange alignment before tightening.
5

Oxygen Sensor (O2 Sensor)

M18 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Use anti-seize compound on sensor threads; torque may vary slightly based on sensor size. This is an estimated value, check sensor specs for proper sizing.
6

NOx Sensor Mounting Bolts/Nuts

M6 x 1.0
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the sensor is properly seated before tightening.

Egr System

1

EGR Valve Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Use a criss-cross pattern for tightening if more than 2 bolts.

Fuel System

1

Fuel Injector Rail Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten bolts evenly to prevent leaks.
2

Fuel Injector Bolts

M5 x 0.8
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten bolts evenly to prevent leaks. Use new seals.

Intake System

1

Mass Air Flow Sensor (MAF) Mounting Screws/Bolts

M5 x 0.8
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Do not overtighten, as the MAF sensor housing is often plastic and can crack.
2

Intake Air Temperature (IAT) Sensor Mounting Bolt/Screws

M5 x 0.8
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Do not overtighten, as the IAT sensor housing is often plastic and can crack.

Exhaust

Torque specifications for Exhaust

Exhaust Manifold

1

Exhaust Manifold/Header to Cylinder Head Bolts (Initial)

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Initial torque for the manifold to cylinder head. Apply in a crisscross pattern to ensure even pressure.
2

Exhaust Manifold/Header to Cylinder Head Bolts (Final)

M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Final torque for the manifold to cylinder head. Apply in a crisscross pattern to ensure even pressure.
3

Exhaust Pipe to Exhaust Manifold/Header Flange Bolts

M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
These bolts connect the exhaust pipe to the manifold/header. Use new gaskets where required.

Catalytic Converter

1

Catalytic Converter to Exhaust Pipe Flange Bolts

M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
These bolts connect the catalytic converter to the exhaust pipe. Use new gaskets where required.

Muffler

1

Muffler to Exhaust Pipe Flange Bolts

M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
These bolts connect the muffler to the exhaust pipe. Use new gaskets where required.

Exhaust Support

1

Exhaust Hanger/Support Bracket Bolts to Chassis

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
These bolts secure the exhaust hangers/support brackets to the chassis. Proper torque ensures the exhaust system is supported correctly.

Oxygen Sensor

1

Oxygen Sensor Mounting Torque

M18 x 1.5
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the sensor is not cross threaded, and use anti-seize if required. Torque to prevent leaks or damage.

Exhaust Clamps

1

Exhaust Clamp Bolt Torque

M8 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Torque value is an estimate and may need to be adjusted based on the clamp size and manufacturer's specifications. Apply torque evenly.

Fuel

Torque specifications for Fuel

Fuel Rail

1

Fuel Rail Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Torque these bolts evenly to ensure proper sealing and prevent distortion of the fuel rail.
2

Fuel Injector Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
These bolts secure the injectors to the fuel rail. Proper torque prevents fuel leaks and ensures correct seating.
3

Fuel Injector Rail Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
These bolts secure the rail to the engine. Proper torque prevents fuel leaks and ensures correct alignment.

Fuel Pump

1

Fuel Pump Mounting Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
These bolts secure the fuel pump module to the fuel tank. Ensure even tightening to prevent damage to the tank.
2

Fuel Tank Strap Bolts

M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
These bolts secure the fuel tank to the chassis. Torque evenly to support the weight of the tank and fuel.
3

Fuel Filler Neck Bolts

M6 x 1.0
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
These bolts secure the fuel filler neck to the body. Torque evenly to prevent leaks of fumes.
4

Fuel Tank Level Sensor Mounting Bolts

M5 x 0.8
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
These bolts secure the level sensor to the tank. Proper torque ensures a leak-free seal and proper function.

Fuel Filter

1

Fuel Filter Bolt/Nut

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
These bolts/nuts secure the fuel filter and housing. Proper torque is essential for a leak-free seal.
2

Fuel Line/Hose Banjo Bolt (at Fuel Rail/Pump)

M12 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
These bolts connect fuel lines to the fuel rail or pump. Always use new crush washers. Torque values can vary; this value is estimated for an M12 bolt. Check manufacturer specifications.

High Pressure Pump

1

High-Pressure Fuel Pump Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
These bolts secure the high-pressure fuel pump to the engine. Ensure even tightening to prevent damage to the pump or block.

Sensors

1

Fuel Pressure Sensor

M10 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
These sensors are typically threaded into the fuel rail or line. Proper torque ensures a leak-free seal. Values estimated based on similar sized components.

Hvac

Torque specifications for Hvac

Ac Compressor

1

A/C Compressor Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure bolts are clean and lightly lubricated. Tighten evenly to avoid misalignment.
2

A/C Line Fittings

Varying, typical M10x1.0 or M12x1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use new O-rings or seals. Ensure fittings are properly aligned. Avoid over-tightening.

Ac Condenser

1

Condenser Mounting Bolts/Nuts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure mounting points are clean and free from debris. Do not over-tighten to avoid damaging mounting tabs.

Ac Evaporator

1

Evaporator Housing Bolts/Fasteners

M5 x 0.8
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Often involves plastic housings, be careful not to overtighten or strip threads. Torque value is estimated based on similar components.

Hvac Controls

1

HVAC Control Module Mounting Bolts/Screws

M4 x 0.7
Torque Specification
4.5 ft-lbs (6 N·m)
Important Notes
Extremely low torque required. Values estimated based on similar electronic component mounting. Use extreme care not to over-tighten.

Blower Motor

1

Blower Motor Mounting Bolts/Screws

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure that the blower motor housing is properly aligned before tightening bolts. Do not overtighten on plastic housings.

Expansion Valve

1

Expansion Valve Mounting Bolts/Screws

M5 x 0.8
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Use new O-rings or gaskets. Be careful not to over-tighten the bolts/screws to avoid leaks.

Heater Core

1

Heater Core Mounting Bolts/Fasteners

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure mounting points are clean and free from debris. Avoid over-tightening, which may cause leaks.

Suspension

Torque specifications for Suspension

Front Strut Assembly

1

Strut/Shock Absorber Mounting Bolts

M12 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Secures the strut to the steering knuckle/wheel hub carrier. Ensure proper torque for suspension integrity.
2

Strut Upper Mount Nuts

M8 x 1.25
Torque Specification
34 ft-lbs (45 N·m)
Important Notes
Fastens the upper strut mount to the chassis. Estimated value, verify with your service manual.

Front Control Arms

1

Control Arm Bolts

M14 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Secures the control arms to the chassis/subframe. Ensure proper torque to maintain alignment and prevent movement.
2

Ball Joint Nut

M12 x 1.5
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Secures the ball joint to the control arm or steering knuckle. Proper torque ensures proper function of the joint.
3

Camber Adjustment Bolt/Nut

M12 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Fastens the camber adjustment bolt. Proper torque is crucial for maintaining alignment.

Steering

1

Tie Rod End Nut

M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Fastens the tie rod end to the steering knuckle. Ensure proper torque for safe and responsive steering.

Sway Bar

1

Sway Bar Link Nut

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Secures the sway bar link to the sway bar and strut/control arm. Ensure proper torque to maintain correct sway bar function.

Wheel Hub And Bearing

1

Wheel Hub/Bearing Bolts

M14 x 1.5
Torque Specification
1. 74 ft-lbs (100 N·m) 2. 90°
Important Notes
Secures the wheel hub/bearing to the steering knuckle. Proper torque is crucial for wheel security and bearing function. These are torque to yield bolts and MUST be replaced when removed.

Subframe

1

Subframe Mounting Bolts

M14 x 1.5
Torque Specification
1. 103 ft-lbs (140 N·m) 2. 90°
Important Notes
Secures the subframe to the chassis. Proper torque is critical for suspension integrity and handling. These are torque to yield bolts and MUST be replaced when removed.

Rear Trailing Arm

1

Rear Trailing Arm Bolts

M14 x 1.5
Torque Specification
89 ft-lbs (120 N·m)
Important Notes
Secures the rear trailing arm to the vehicle chassis. Proper torque is crucial for rear suspension control and function.

Troubleshooting Guide

Common issues, diagnostic steps, and prevention guidelines

Common Issues

Bolt stretching, stripped threads, uneven torque patterns

Loose Components

Symptoms:
  • Rattling or vibration noises
  • Visible movement in components
  • Uneven panel gaps
Solutions:
  • Clean threads and mounting surfaces
  • Replace damaged fasteners
  • Apply proper torque in sequence
  • Use thread locker if specified

Stripped Fasteners

Symptoms:
  • Unable to achieve proper torque
  • Fastener spins freely
  • Visible thread damage
Solutions:
  • Use thread repair kit if appropriate
  • Install thread insert (HeliCoil)
  • Replace component if threaded hole is damaged
  • Upgrade to higher grade fastener if recommended

Overtightened Components

Symptoms:
  • Cracked or deformed parts
  • Broken fasteners
  • Compressed gaskets or seals
Solutions:
  • Replace damaged components
  • Use new fasteners
  • Follow proper torque sequence
  • Verify correct torque specifications

Diagnostic Steps

Visual inspection, torque verification, thread assessment

1

Visual Inspection

Inspect the affected area for any visible signs of damage or wear

  • Check for cracks or deformation
  • Look for signs of excessive wear
  • Verify proper fastener installation
2

Torque Verification

Verify the torque applied to the fasteners

  • Check the torque wrench calibration
  • Verify the torque specification
  • Compare the applied torque to the specification
3

Thread Assessment

Assess the condition of the threads

  • Check for signs of thread damage
  • Verify the thread type and size
  • Check for proper thread engagement

Prevention Guidelines

Best practices, maintenance tips, tool care

Best Practices

  • Always follow the recommended torque specification
  • Use the correct type and size of fasteners
  • Verify the torque wrench calibration regularly

Maintenance Tips

  • Regularly inspect the affected area for signs of wear or damage
  • Replace damaged or worn-out components promptly
  • Keep the work area clean and organized

Tool Care

  • Regularly clean and maintain the torque wrench
  • Store the torque wrench in a dry and secure location
  • Verify the torque wrench calibration before each use

Frequently Asked Questions

Find answers to common questions about torque specifications

Q1

What IS the recommended torque for the lug nuts on a 2017-Present BMW 430i?

The recommended torque for the lug nuts IS 110 Nm (81 lb-ft).

Q2

What IS the correct torque for the oil filter housing bolts on a 2017-Present BMW 430i?

The correct torque for the oil filter housing bolts IS 25 Nm (18 lb-ft).

Q3

What torque wrench should I use to ensure accuracy when tightening bolts on my 2017-Present BMW 430i?

BMW recommends using a torque wrench with a range of 20-200 Nm (15-150 lb-ft) and an accuracy of at least ±4%.

Q4

Are there any specific torque sequences I should follow when tightening bolts on my 2017-Present BMW 430i?

Yes, BMW provides specific torque sequences for various components. Refer to the vehicle's service manual for detailed instructions.

Q5

What are the consequences of over- or under-tightening bolts on my 2017-Present BMW 430i?

Over-tightening can damage threads and components, while under-tightening can result in loose or insecure connections. Both can compromise the safety and reliability of the vehicle.

Q6

Can I use a regular wrench to tighten bolts on my 2017-Present BMW 430i?

While it IS possible to use a regular wrench in some cases, it IS not recommended as it can be difficult to achieve the precise torque required. A torque wrench IS the recommended tool for accurate and safe bolt tightening.

Environmental Considerations

Temperature, humidity, and seasonal effects on torque specifications

Temperature Effects

Includes: High Heat, Cold Weather, Thermal Cycling

Temperature can significantly impact torque values and fastener behavior

Cold Weather

Effects:
  • Increased material brittleness
  • Higher torque required due to thread contraction
  • Reduced thread lubricant effectiveness
Recommendations:
  • Allow components to warm to room temperature when possible
  • Consider using winter-grade thread lubricants
  • Check torque values more frequently during winter months

Hot Weather

Effects:
  • Thermal expansion of components
  • Decreased friction in threads
  • Accelerated lubricant breakdown
Recommendations:
  • Check torque when components are at normal operating temperature
  • Use temperature-resistant thread lockers
  • Consider re-torquing after heat cycles

Humidity and Corrosion

Covers: Rust Prevention, Salt Exposure, Moisture Control

Moisture and corrosion can affect fastener integrity and torque values

High Humidity

Effects:
  • Accelerated corrosion formation
  • Reduced friction coefficient
  • Potential thread seizing
Prevention:
  • Use corrosion-resistant fasteners
  • Apply appropriate anti-seize compounds
  • Maintain proper protective coatings

Salt Exposure

Effects:
  • Rapid corrosion development
  • Thread damage
  • Seized fasteners
Prevention:
  • Regular underbody washing
  • Use of sacrificial anodes where appropriate
  • Application of protective coatings

Seasonal Maintenance

Spring, Summer, Fall, and Winter maintenance schedules

Spring

  • Inspect for winter damage
  • Clean and protect exposed fasteners
  • Check torque on critical components

Summer

  • Monitor heat-affected components
  • Check expansion-related loosening
  • Inspect cooling system mounts

Fall

  • Prepare for winter conditions
  • Apply corrosion protection
  • Verify all fasteners are properly torqued

Winter

  • More frequent inspection of critical fasteners
  • Check for salt damage
  • Monitor suspension component torque

Related Resources

Tools, service procedures, and technical bulletins

Recommended Tools

Digital Torque Wrench (10-100 Nm)

Essential for tightening fasteners to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the 430i.

  • Digital display for accurate readings
  • Audible alarm when target torque IS reached
  • Multiple units (Nm, ft-lb, in-lb)
  • Reversible ratcheting mechanism
Learn more
Service Procedures
Technical Service Bulletins

Legal Disclaimer

Important information about using this content

Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.

General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability

The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.

We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.

Technical Information
  • All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
  • Vehicle specifications and procedures may vary by model year, trim level, and region.
  • Always follow the manufacturer's recommended procedures and safety precautions.
  • Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
  • If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.

About the Author

Expert automotive knowledge and experience

Alan Montanye - Automotive Technical Specialist
ASE

Alan Montanye

Automotive Technical Specialist

ASE Master Certified Technician with over a decade of hands-on experience in automotive repair and diagnostics.

Facebook Contact
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions

Diagnostic

Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.

Repair

Expert in both traditional mechanical repairs and modern vehicle systems.

Additional Expertise

Documentation

Created over 500 detailed repair guides and technical documents.

Training

Conducted technical training sessions and contributed to repair databases.

Certifications & Research

Certifications

  • ASE Master Technician Certification
  • Advanced Diagnostic Specialist
  • Hybrid/Electric Vehicle Systems
  • Performance Tuning Expert

Research & Community

Actively researches emerging technologies and contributes to automotive forums.

© 2025 BMW Specs. All rights reserved.

Privacy Policy Terms of Service